Replace the sparse Heltec V4 R8 observer home screen with a padded dark
analytics dashboard, add manual display control, and make blanking a runtime
setting.
Dashboard (DISPLAY_ACTIVITY_DASHBOARD, the four R8 TFT observer envs):
- RadioActivityWindow: 20 one-minute buckets of valid RX packets, no heap.
The caller's 32-bit millis() is extended to a monotonic 64-bit clock, so
nothing downstream has a rollover case; an always-on node passes 2^32 ms
after ~49.7 days, which would otherwise re-enter warm-up and divide 20
minutes of traffic by seconds. Rates use 19 whole minutes plus the elapsed
part of the current one rather than a fixed 1200 s.
- ObserverDashboard: header, radio strip, headline totals, a 20-bar
packets-per-minute graph and RF/status footers, with separate portrait and
landscape layouts. A text row is a fixed 16 px, which is 3.2 logical units
in portrait but 4.27 in landscape, so one shared grid would overlap.
Text is trimmed by character budget, not measured width: getTextWidth()
reports an over-long string at the portrait driver's fallback scale, so
DisplayDriver::drawTextEllipsized() under-trims and the row renders at half
height.
- Six per-row signatures computed from what is actually drawn, so only the
rows whose pixels changed repaint. No startFrame(), no whole-screen clear.
Link state moved out of the full-frame signature, so a DHCP renewal or WiFi
flap repaints one footer row instead of the panel.
- Dark theme by retuning the UIColor statics at runtime, which needs no
display-driver edit and carries boot, setup, reboot and power-off with it.
Touch and button (DISPLAY_TOUCH_TOGGLE):
- CHSC6X at I2C 0x2E, polled; TP_INT is unusable (optional R13, and GPIO 43
is U0TXD). The point-count byte is tested against a valid count, never
against non-zero: an idle read returns 0xFF, which reads as a finger held
down forever and latches the tap detector after one event.
- turnOff() no longer parks PIN_TFT_RST low on this board. GPIO 21 is a
shared LCD_RST/TP_RST net, so doing that held the touch controller in
reset for as long as the display was off. Verified against Heltec's
expansion-board and mainboard schematics and the V4-R8 datasheet pinout,
which also correct the pin comment in HeltecV4R8Board.cpp.
- The USER button click now toggles the display too; it previously did
nothing whenever the display was already on.
display.timeout:
- `set display.timeout <secs>` / `get display.timeout`, 0 = stay on, 60 s
default, 3600 max. Read live, so a change applies without a reboot and
restarts the countdown rather than firing on the old deadline.
- Stored in MQTTPrefs (/mqtt.json), keeping NodePrefs aligned with upstream.
Runtime-only: LegacyV1MQTTPrefs and the four frozen binary payload sizes
are unchanged. No JSON format-version bump - the loader skips keys no
def() claims, so older firmware reads newer files and this firmware reads
older ones with the default applied. Both directions are covered by tests.
- Joins the observer atomic-setter contract, so a failed save rolls the live
value back instead of only claiming to.
New periodic work uses a wrap-safe deadline check; `millis() >= deadline`
fires every loop for a whole interval before each rollover.
Adds test_radio_activity_window, test_observer_dashboard (driving the real
renderer against a recording DisplayDriver in both orientation profiles) and
test_touch_tap_detector. 440 native cases pass.
Framework for upcoming variant-specific PRs that add LED feedback during boot. The hook gives users visual cues that the device is busy and
shouldn't be interacted with until startup completes.
The Ethernet retry loop in repeater and room server checked
hardwareStatus() and linkStatus() before calling Ethernet.begin(),
which always returned EthernetNoHardware since hardware detection
only happens during begin(). Extract shared Ethernet CLI code into
EthernetCLI.h to prevent future divergence. Also fix time_t type
mismatch in companion radio Ethernet init.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Rename eth command to eth.status for consistency with other commands
- Rename generateDeviceMac to generateEthernetMac for clarity
- Refactor ethernet_handle_command to return false by default
- Allow new TCP clients to replace existing connections (repeater, room server, SerialEthernetInterface)
- Boot companion radio without Ethernet on init failure (LoRa-only recovery mode)
- Remove > prompt from ethernet CLI for consistency with serial interface
- Fix variable redeclaration compile error in SerialEthernetInterface when ETHERNET_STATIC_IP is defined
- Fix TCP socket leak when duplicate client detection fires
- Remove dead recv_queue and adv_restart_time members from SerialEthernetInterface
- Fix port numbers in docs (port 23 for repeater/room server CLI, port 5000 for companion radio)
- Clarify eth.status command is only available in repeater and room server firmware
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add W5100S Ethernet adapter support for RAK4631-based firmware, enabling
TCP CLI access on port 23 as an alternative to BLE/Serial connections.
- New SerialEthernetInterface for nRF52 with DHCP, reconnection handling,
and shared WB_IO2 power pin management with GPS module
- Ethernet build targets for repeater, room server, and companion firmware
- Prevent GPS from toggling WB_IO2 when Ethernet module is active
- CI build check for all three ETH firmware targets
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* Sensor, anon_req now just for admin login (guest password now unused)
* special CLI command, "setperm {pubkey-hex} {permissions-int16}" for admin(s) to manage user access (permissions 0 = remove)
agessaman