Integrates Mike Carper's transmission-reliability work (direct retries with
SNR-adaptive backoff and CR, flood retry controls, alt-path replies, flood
channel gates) plus its upstream/dev base (as of 2026-07-06) on top of the
observer stack. The flex branch is untouched; this branch is the experimental
integration line.
Conflict-resolution decisions, for future re-syncs (git rerere is enabled and
has recorded these):
- NodePrefs adopts keymind/upstream member order + retry/flood tail. Member
order is in-memory only: /com_prefs stays field-by-field with the same
canonical file order both sides already share through offset 294; keymind
appends the retry tail at 295+ (new canonical size 676). Flex fleet files
load unchanged; retry fields default via direct_retry_prefs_magic.
- loadPrefsInt keeps the fork's legacy MQTT-gap recovery but moves its
detection boundary from 'extra > 5' to 'extra > LEGACY_MQTT_GAP_3SLOT (864)'
so keymind-size tails take the normal read path. COM_PREFS_TAIL_BYTES
retired.
- Dispatcher/RadioLibWrappers: fork watchdog additions + keymind TX overrides
and CAD busy counter are unioned; RxReservePacketManager::queueOutbound
follows upstream's new bool return (false when shedding).
- CommonCLI: fork observer dispatch + versioned /mqtt_prefs machinery kept;
keymind CLI (retry/flood/radioat) taken; duplicate CAD/FEM handlers and
sanitise lines deduped (kept keymind placements to minimize future diff).
- MyMesh (repeater/room): fork alerter/OTA/observer wiring kept; keymind
scheduled-radio system replaces the old pending_* temp-radio members;
applySavedRadioParams() replaces raw setParams at startup.
- ESP32Board: fork manifest-OTA + keymind powerOff/deepSleep and stopOTAUpdate
unioned; startOTAUpdate keeps fork's STA-aware IP with keymind's idempotency
guard.
- build.sh taken wholesale from keymind (fleet builds use GH Actions).
Verified: Heltec_v3_repeater_observer_mqtt, Heltec_v3_repeater,
heltec_v4_repeater_observer_mqtt, Heltec_v3_room_server_observer_mqtt build;
host migration harness (13 MQTT + non-MQTT scenarios) passes with updated
expectations (676-byte /com_prefs; odd-size files normalize on save, not
load); native unit tests 13/13.
GPS support was implemented incorrectly for the ThinkNode M3. The reset
pin was being driven when it should be left floating for this unit. The
enable pin also wasn't being picked up by `MicroNMEALocationProvider`
because of a mismatch in constant naming conventions. I did a general
cleanup of the GPS and ThinkNode M3 bring-up code so that constant names
line up and "*_ACTIVE" constants are used consistently vs hardcoding
`HIGH`/`LOW`. After making these changes, serial data immediately starts
streaming in from the NMEA on boot and GPS detection just works.
LED handling was also not quite right for the ThinkNode M3. The LoRa TX
LED was being driven high to turn it on when it should actually be
driven low. I changed the code to use the `LED_STATE_ON` constant and
also added a little code to the shutdown path to properly make sure that
all LEDs are turned off.
Tested and confirmed working on real hardware.
Resolves both #1864 and #2879.
Switch these existing variants from `nrf52_base` to `rak4631_hw` (which adds
ENABLE_OTA + the in-place flash store + the EndF post-build hook), so they get
OTA-over-LoRa. Scope is limited to variants already covered by the
Adafruit_nRF52_Bootloader_OTAFIX in-place apply — no new variants are added.
OtaTargets.h is regenerated to include their target ids.
Enable GPS time synchronization across all variants by passing
&rtc_clock to MicroNMEALocationProvider. When GPS gets a valid
fix, the RTC clock is now updated automatically every 30 minutes.
Updated 16 variants: rak4631, lilygo_tbeam_SX1262, rak_wismesh_tag,
lilygo_tbeam_supreme_SX1262, thinknode_m3, heltec_v4, thinknode_m1,
lilygo_tbeam_SX1276, meshadventurer, nano_g2_ultra, heltec_v3,
promicro, xiao_c3, heltec_tracker_v2, keepteen_lt1, heltec_mesh_solar.
mikecarper