HaloKeymind/docs/espnow_bridge_setup.md

ESP-NOW bridge: simple setup

Use two ESP32 LoRa boards to join two MeshCore networks with different radio settings. Each board repeats on its own LoRa network, and the boards exchange packets directly over 2.4 GHz ESP-NOW. No router, internet connection, or manual peer pairing is needed.

LoRa network A <--> Repeater A <-- ESP-NOW --> Repeater B <--> LoRa network B

1. Choose the firmware

Install the exact board's Full ESP-NOW bridge repeater image on each board. The target name ends in _repeater_bridge_espnow; a standard Heltec V4 uses heltec_v4_repeater_bridge_espnow. Full/MQTT and Full Companion images are different choices. See the firmware picker guide.

Open each board's USB console at 115200 baud and run:

get bridge.type

The answer must be espnow. mqtt, rs232, or none means that image does not provide the ESP-NOW bridge described here.

2. Set each board's LoRa network

Configure one board at a time over USB. Replace the placeholders below with the radio settings used by the network on that board's side. Use Bridge-A for the first board and Bridge-B for the second, or choose your own names.

set bridge.enabled off
set name Bridge-A
set radio <freq>,<bw>,<sf>,<cr>
reboot

Do not type the angle-bracket placeholders literally.

Radio option	Meaning
freq	LoRa frequency in MHz. Match the local network on this side.
bw	LoRa bandwidth in kHz. Match that network's bandwidth.
sf	Spreading factor, 5-12. Match that network's setting.
cr	Coding-rate value, 5-8. Match that network's setting.
name	A label to tell the two repeaters apart. It does not pair them.

set radio requires a reboot to apply. After reconnecting, get radio shows the saved settings. Use permanent radio settings for this setup; tempradio sessions expire.

3. Configure the ESP-NOW link on both boards

Run this block on both boards. Replace YourSharedKey with the same case-sensitive secret on each board, using 1-15 characters. Channel 6 is an example; both boards must use the same channel.

set bridge.enabled off
set bridge.channel 6
set bridge.format wrapped
set bridge.secret YourSharedKey
set bridge.source tx
set bridge.delay 500
set repeat on
set bridge.enabled on

These settings are saved across reboot. Bridge changes apply immediately; changing an enabled bridge's channel, format, or secret restarts the bridge. Stopping it first lets you finish configuring both sides before connecting them.

What each bridge option does

Option	Choices and purpose
bridge.enabled	on starts the bridge; off stops it and keeps its saved settings.
bridge.channel	The 2.4 GHz channel, 1-13. Match it on both boards. This is separate from the LoRa frequency in set radio.
bridge.format	wrapped is the default for this two-repeater setup and uses the shared secret. raw connects to primary-ESP-NOW nodes such as Generic_ESPNOW or SenseCapIndicator-ESPNow; it ignores the secret. Both peers must use compatible formats.
bridge.secret	A matching, case-sensitive value of 1-15 characters for wrapped mode. It separates bridge groups; it is not strong encryption. MeshCore's own message encryption remains in place.
bridge.source	tx crosses packets this repeater transmits on LoRa, after its forwarding decisions; use this for the setup above. rx crosses received packets before those decisions and can pass traffic the local repeater would not forward.
bridge.delay	Wait before processing a packet received from the other bridge, in milliseconds. Range: 0-10000. Start with the default 500.
repeat	on enables normal LoRa forwarding; off disables forwarding. Keep it on on both bridge repeaters. Normal routing, scope, and packet-filter rules still apply.
bridge.type	Read-only firmware capability. It must report espnow for this guide.
bridge.running	Read-only runtime state. on means the local bridge started; it does not prove the other board is reachable.

This fork uses set bridge.source tx or rx. Some upstream guides use logTx and logRx; those are not the command values used here.

For a LoRa gateway connected to primary-ESP-NOW Companions instead of another LoRa repeater, see raw ESP-NOW compatibility.

4. Check the link

Run on both boards:

get bridge.enabled
get bridge.running
get bridge.channel
get bridge.format
get bridge.secret
get bridge.source
get bridge.delay
get repeat
get radio

Expected: enabled and running on, matching channel/format/secret, source tx, delay 500, repeat on, and the intended LoRa settings on each side.

Send a message from a Companion on network A to one on network B, then reply from B to A. Check both directions; configuration readback alone does not test delivery.

If it does not work:

• Commands are unavailable: check get bridge.type and the firmware choice.
• Enabled is on but running is off: initialization failed. Reboot and check again; ensure another WiFi service is not occupying the radio.
• Both are running but traffic does not cross: compare channel, format, and secret; confirm each board's LoRa settings were applied with a reboot, and check the networks' forwarding and scope rules.

A running bridge keeps the device awake, even with device power saving enabled. For every command's full details, see the bridge CLI reference.

For a broader comparison with a Linux-based bridge, see the MeshCore Nexus bridging guide.