mirror of
https://github.com/mikecarper/MeshCore.git
synced 2026-09-16 19:22:54 +00:00
88 lines
2.2 KiB
C++
88 lines
2.2 KiB
C++
#include "HeltecRC32Board.h"
|
|
|
|
void HeltecRC32Board::begin() {
|
|
ESP32Board::begin();
|
|
|
|
pinMode(PIN_ADC_CTRL, OUTPUT);
|
|
digitalWrite(PIN_ADC_CTRL, !ADC_CTRL_ENABLED);
|
|
|
|
#ifdef SENSOR_RST_PIN
|
|
pinMode(SENSOR_RST_PIN, OUTPUT);
|
|
digitalWrite(SENSOR_RST_PIN, HIGH);
|
|
#endif
|
|
|
|
#ifdef LED_POWER
|
|
pinMode(LED_POWER, OUTPUT);
|
|
digitalWrite(LED_POWER, LOW);
|
|
#endif
|
|
|
|
periph_power.begin();
|
|
periph_power.claim();
|
|
#ifdef RC32_PERIPHERAL_WARMUP_MS
|
|
delay(RC32_PERIPHERAL_WARMUP_MS);
|
|
#endif
|
|
|
|
esp_reset_reason_t reason = esp_reset_reason();
|
|
if (reason == ESP_RST_DEEPSLEEP) {
|
|
long wakeup_source = esp_sleep_get_ext1_wakeup_status();
|
|
if (wakeup_source & (1L << P_LORA_DIO_1)) {
|
|
startup_reason = BD_STARTUP_RX_PACKET;
|
|
}
|
|
|
|
rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS);
|
|
rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1);
|
|
}
|
|
}
|
|
|
|
void HeltecRC32Board::onBootComplete() {
|
|
#ifdef ESP32_POST_BOOT_CPU_FREQ
|
|
const uint32_t current_mhz = getCpuFrequencyMhz();
|
|
if (current_mhz > ESP32_POST_BOOT_CPU_FREQ) {
|
|
if (setCpuFrequencyMhz(ESP32_POST_BOOT_CPU_FREQ)) {
|
|
MESH_DEBUG_PRINTLN("RC32 startup complete; CPU reduced from %lu to %u MHz",
|
|
(unsigned long)current_mhz,
|
|
(unsigned)ESP32_POST_BOOT_CPU_FREQ);
|
|
} else {
|
|
MESH_DEBUG_PRINTLN("RC32 could not set post-boot CPU frequency to %u MHz",
|
|
(unsigned)ESP32_POST_BOOT_CPU_FREQ);
|
|
}
|
|
}
|
|
#endif
|
|
}
|
|
|
|
void HeltecRC32Board::powerOff() {
|
|
enterDeepSleep(0);
|
|
}
|
|
|
|
void HeltecRC32Board::onBeforeTransmit() {
|
|
digitalWrite(P_LORA_TX_LED, HIGH);
|
|
}
|
|
|
|
void HeltecRC32Board::onAfterTransmit() {
|
|
digitalWrite(P_LORA_TX_LED, LOW);
|
|
}
|
|
|
|
uint16_t HeltecRC32Board::getBattMilliVolts() {
|
|
analogReadResolution(12);
|
|
analogSetAttenuation(ADC_2_5db);
|
|
digitalWrite(PIN_ADC_CTRL, ADC_CTRL_ENABLED);
|
|
delay(10);
|
|
uint32_t raw = 0;
|
|
for (int i = 0; i < 8; i++) {
|
|
raw += analogReadMilliVolts(PIN_VBAT_READ);
|
|
}
|
|
raw = raw / 8;
|
|
digitalWrite(PIN_ADC_CTRL, !ADC_CTRL_ENABLED);
|
|
|
|
return (adc_mult * raw);
|
|
}
|
|
|
|
bool HeltecRC32Board::setAdcMultiplier(float multiplier) {
|
|
adc_mult = multiplier == 0.0f ? ADC_MULTIPLIER : multiplier;
|
|
return true;
|
|
}
|
|
|
|
const char* HeltecRC32Board::getManufacturerName() const {
|
|
return "Heltec RC32";
|
|
}
|