mirror of
https://github.com/mikecarper/MeshCore.git
synced 2026-09-16 14:42:39 +00:00
84 lines
2.5 KiB
C++
84 lines
2.5 KiB
C++
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
#include "nrf_gpio.h"
|
|
#include "nrf_sdm.h"
|
|
#include "nrf_soc.h"
|
|
|
|
#include "RAK4631Board.h"
|
|
|
|
#ifdef ETHERNET_ENABLED
|
|
// Drive WB_IO2 HIGH as early as possible using direct register access.
|
|
// WB_IO2 (P1.02, Arduino pin 34) controls the WisBlock slot power switch.
|
|
// With POE through RAK13800, this must be enabled before the framework
|
|
// initializes or the board will brownout from insufficient power delivery.
|
|
// Priority 102 runs just after SystemInit.
|
|
static void __attribute__((constructor(102))) rak4631_early_poe_power() {
|
|
nrf_gpio_cfg_output(NRF_GPIO_PIN_MAP(1, 2)); // WB_IO2 = P1.02
|
|
nrf_gpio_pin_set(NRF_GPIO_PIN_MAP(1, 2));
|
|
}
|
|
#endif
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Static configuration for power management
|
|
// Values set in variant.h defines
|
|
const PowerMgtConfig power_config = {
|
|
.lpcomp_ain_channel = PWRMGT_LPCOMP_AIN,
|
|
.lpcomp_refsel = PWRMGT_LPCOMP_REFSEL,
|
|
.voltage_bootlock = PWRMGT_VOLTAGE_BOOTLOCK
|
|
};
|
|
|
|
void RAK4631Board::initiateShutdown(uint8_t reason) {
|
|
// Disable LoRa module power before shutdown
|
|
digitalWrite(SX126X_POWER_EN, LOW);
|
|
|
|
if (reason == SHUTDOWN_REASON_LOW_VOLTAGE ||
|
|
reason == SHUTDOWN_REASON_BOOT_PROTECT) {
|
|
configureVoltageWake(power_config.lpcomp_ain_channel, power_config.lpcomp_refsel);
|
|
}
|
|
|
|
enterSystemOff(reason);
|
|
}
|
|
#endif // NRF52_POWER_MANAGEMENT
|
|
|
|
void RAK4631Board::begin() {
|
|
#ifdef RAK4631_COMPANION_FORCE_LDO
|
|
// Some RAK4631 battery/board combinations have proved unstable with the
|
|
// nRF52 DC/DC enabled. Explicitly select the LDO for companion firmware;
|
|
// merely skipping NRF52BoardDCDC::begin() would inherit any prior state.
|
|
NRF52Board::begin();
|
|
uint8_t sd_enabled = 0;
|
|
sd_softdevice_is_enabled(&sd_enabled);
|
|
if (sd_enabled) {
|
|
sd_power_dcdc_mode_set(NRF_POWER_DCDC_DISABLE);
|
|
} else {
|
|
NRF_POWER->DCDCEN = 0;
|
|
}
|
|
#else
|
|
NRF52BoardDCDC::begin();
|
|
#endif
|
|
pinMode(PIN_VBAT_READ, INPUT);
|
|
#ifdef PIN_USER_BTN
|
|
pinMode(PIN_USER_BTN, INPUT_PULLUP);
|
|
#endif
|
|
|
|
#ifdef PIN_USER_BTN_ANA
|
|
pinMode(PIN_USER_BTN_ANA, INPUT_PULLUP);
|
|
#endif
|
|
|
|
|
|
#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
|
|
Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
|
|
#endif
|
|
|
|
Wire.begin();
|
|
|
|
pinMode(SX126X_POWER_EN, OUTPUT);
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Boot voltage protection check (may not return if voltage too low)
|
|
// We need to call this after we configure SX126X_POWER_EN as output but before we pull high
|
|
checkBootVoltage(&power_config);
|
|
#endif
|
|
digitalWrite(SX126X_POWER_EN, HIGH);
|
|
delay(10); // give sx1262 some time to power up
|
|
}
|