Picks up upstream MeshCore 1.17.1.
Notable upstream content:
- 1.17.1 version/build-date bump in the example MyMesh headers.
- nRF52: combine radio entropy with CC310 RNG.
- Companion FEM prefs: load/save of fem_ properties commented out until they
can be set from the client.
- Scoped reply routing: replies no longer dropped when flood.max.unscoped is
low (RoutingPolicy + unit tests).
- nRF52 unused-pin sweep (T1, T-Echo Lite, MeshPocket).
No conflicts.
Brings in the external FEM gain preferences (fem_txgain, PR #3137 plus the
companion-side port), the AGC reset rxgain fix, the LR2021 preamble/IRQ
timeout logic, and assorted variant fixes (T096, T-Echo Card TCXO, promicro
pinmap, minewsemi, R1 Neo).
Conflict resolutions:
- SH1106Display: both sides fixed T-Beam Supreme startup independently. Kept
our _initialized guard and DISPLAY_ADDRESS_ALT override, took upstream's
SA0-pair fallback and its unconditional display.begin() so the frame buffer
is allocated even when no panel answers.
- MyMesh/SensorMesh/CommonCLI: took upstream's fem_txgain default and wiring,
kept our comments and the observer-side prefs layout.
Also fixes CustomLLCC68Wrapper, which upstream missed when sx126xResetAGC
gained its rx_boost_gain parameter. No variant builds that wrapper today, so
neither tree failed to compile.
Picks up upstream MeshCore 1.17.0 and the dev commits that followed it.
Notable upstream content:
- 1.17.0 version/build-date bump in the example MyMesh headers.
- anon_req hardening: reply_path_len is now uint8_t with an isValidPathLen()
bounds check and a 0xFF sentinel; reply_path_hash_size is gone.
- LR2021 support (Meshnology W12, Seeed MeshTracker X1) incl. side detectors,
multi-SF and the new `extra.sf` get/set CLI.
- CustomLFS 0.2.2 -> 0.2.3 (GD25Q64C support).
- kiss_modem envs for several nRF52 variants; ThinkNode M6 GPS/flash fixes.
Conflicts resolved:
- platformio.ini: took upstream's CustomLFS 0.2.3, kept our lib_ignore for
the vendored PsychicMqttClient.
- CommonCLI.h: kept both upstream's USE_LR2021 configSideDetectors() hook and
our fault-alert callbacks.
NodePrefs gains upstream's extra_sf[4], which is not registered with
ConfigSerializer, so /prefs.json layout is unchanged.
Verified: 275/275 native host tests pass; Heltec_v3_repeater_observer_mqtt,
Heltec_v3_repeater and heltec_v4_repeater_observer_mqtt all build.
Adding build_date to the WebConfigServer constructor broke every
*_room_server_observer_mqtt target: simple_room_server constructs the portal as
well, and only simple_repeater was updated. Nothing caught it because every
build run to that point had been a repeater target.
Neighbors publication was gated on BOARD_HAS_PSRAM. Removing that gate alone
was not enough: the feature built but was inert without PSRAM, because three
allocation sites asked for MALLOC_CAP_SPIRAM (which returns null with no
PSRAM), the bridge's persistent buffer was allocated inside a BOARD_HAS_PSRAM
block, and neighborDiscoverReady() rejected every pass at runtime on
psramFound(). The entry table also did not fit: finishNeighborDiscover put
pubkey_hex[50][65] plus entries[50] on the stack, a 4752-byte frame against
the mesh loop task's 8 KB.
- Gate on MAX_NEIGHBOURS plus PSRAM or an explicit per-variant
MQTT_NEIGHBORS_WITHOUT_PSRAM opt-in.
- Move the entry table and its hex strings into one heap block sized to the
pass; the frame drops from 4752 to 304 bytes.
- Prefer PSRAM and fall back to internal DRAM in the mesh-side allocations
and the ArduinoJson pool; hoist the bridge's persistent buffer out of the
BOARD_HAS_PSRAM block (psram_malloc already falls back).
- Keep the runtime psramFound() check only where the buffers are sized for
PSRAM, so a board whose PSRAM failed to init still refuses.
- Size for internal DRAM without PSRAM: 4 KB text buffer and 20 entries per
publish, keeping the pool to a single block and the peak near 13 KB rather
than ~35 KB. Oversized tables truncate and report total_neighbors as before.
Enabled on the ESP32-S3 observer envs (Heltec V3/WSL3, RAK3112, Heltec
Tracker v1.1/v2). Left off for the classic ESP32 T-LoRa V2.1-1.6, which is
already limited to one active TLS slot.
Costs ~7.4 KB static DRAM on repeaters and ~9.6 KB on room servers. The
prefs layout is unchanged, so this is neutral for existing devices.
ArduinoJson v7 hands out document-pool blocks in fixed 4096-byte chunks, so
the pool is not bounded by the size of the text it serialises to. Budgeting
it at NEIGHBORS_JSON_BUFFER_SIZE starved it once the table grew: a 50-entry
table needs 12541 B of pool against the 10240 B cap, and a starved allocator
sets doc.overflowed(), which makes buildNeighborsMessage return 0 and drop
the entire publish rather than truncating the tail.
Repeaters with roughly 40 or more neighbours therefore published no neighbors
message at all, silently, while smaller tables published normally.
Give the pool its own NEIGHBORS_DOC_POOL_BUDGET and add an explicit
NEIGHBORS_MAX_PUBLISH_ENTRIES cap alongside the existing text-size check.
A neighbour heard before the clock is set carries the firmware's unset-clock
default (1715770351, 15 May 2024). Subtracting that from an NTP-synced clock
published ages of ~806 days for neighbours that had just answered a live scope
query, and a backwards clock step reported 0, i.e. "heard just now".
- finishNeighborDiscover() reports the age as unknown ("heard_secs_ago": null)
when the stored stamp and the current clock come from different epochs, or
when the clock has stepped backwards
- handleNeighborDiscoverResponse() re-stamps heard_timestamp on a zero-hop scope
reply, in both the snapshot and the live table, so entries heal once per
discovery cycle instead of waiting for the neighbour's next advert
- publish ordering places usable ages ahead of unknown ones so a poisoned stamp
cannot displace fresh entries when the JSON buffer truncates
- document the null case, and the always-present total_neighbors /
queried_neighbors / truncated fields the payload sample omitted
- add UPSTREAM_BUGS.md, tracking the monotonic-uptime fix to propose upstream
plus the unclamped subtraction in the companion and CLI readouts
Containment only: upstream still stamps neighbours from the wall clock at
packet-reception time, which on a cold boot always precedes NTP.
Absorbs 106 upstream commits. Seven files conflicted; the substantive one
was upstream's new JSON ConfigSerializer (PR #2982), which replaces the
binary /com_prefs layout with /prefs.json and makes NodePrefs a
ConfigSerializer subclass.
Prefs migration
- Adopt upstream's ConfigSerializer. writeCommonPrefsImage() and its
documented offsets (0-294) are deleted, along with the now-unreachable
saveCommonPrefsImageAtomically()/CommonPrefsFileStore atomic rename path.
- Load order is /prefs.json, then /com_prefs, then /node_prefs. Upstream
dropped the /node_prefs fallback; it is restored here so devices that
never advanced past that filename keep their config.
- Legacy files are never removed, so migration cannot destroy its own
source and a deferred or failed save simply retries next boot.
- /com_prefs is treated as a format migration only, not an "upgrade", so
it does not trip the bridge.source tx->rx flip on existing nodes.
- The MQTTPrefsAtomicStore legacy gate is retained: the observer tail
recovered from an old-format file still commits to /mqtt_prefs before
/prefs.json is written.
- MQTTPrefs and /mqtt_prefs are untouched; savePrefs keeps its save_mqtt
parameter and now returns upstream's bool.
Fixes to upstream code
- RadioPrefs::structure() bound both "rxgain" and "fem_rxgain" to
rx_boosted_gain, so radio_fem_rxgain was never persisted. Bound to the
correct field.
- discovery_mod_timestamp was dropped from structure(); it gates
'since'-filtered DISCOVER replies and is set on every config change, so
losing it would silently stop discovery responses after a reboot. Added
as "disc_mod".
Merge artifacts repaired
- Restored bblanchon/ArduinoJson to the native test env; a clean but wrong
auto-merge at the lib_deps block boundary dropped it and broke all 19
host test suites.
- Migrated the fork's WebConfig UITask screens off the removed
DisplayDriver::Color enum to upstream's UIColor element types.
- Removed duplicate getCADEnabled() definitions in companion MyMesh.cpp
and simple_sensor SensorMesh.cpp that both sides had added.
- Dropped memset(&_prefs, 0, ...) in the four example meshes; NodePrefs now
has a vtable. guard gains an initializer that memset used to provide.
Other resolutions
- simple_room_server keeps both the fork's discover.* commands and
upstream's new room.post.
- docs/payloads.md taken from upstream, undoing content earlier merges had
reverted (Control data section, split login tables).
Verified: 273/273 host tests pass across native and native_kiss_modem;
Heltec v3 repeater, repeater_observer_mqtt, room_server_observer_mqtt,
sensor, and companion_radio_ble all build clean.
Enhance the neighbor discovery JSON structure by introducing a
default_scope field, which indicates the region name this node
floods to by default. This change improves clarity in the
neighbor discovery process and aligns with the unscoped flood
behavior when no default region is set. Updates include
modifications to the MyMesh class and related message building
functions to accommodate the new field.
Add support for named packet types in per-slot filters, allowing users
to specify packet types using descriptive names alongside numeric values.
This improves usability and clarity in configuring MQTT slot filters.
Updates include modifications to the parsing logic, WebConfig interface,
and related documentation to reflect the new naming conventions.
Introduce new methods to manage neighbor discovery JSON budget and
entries in MyMesh. This includes tracking the number of queried and
published neighbors, measuring JSON sizes, and handling truncation
when the buffer limit is reached. These improvements optimize the
neighbor discovery process and ensure efficient JSON message
construction for MQTT communications.
Add functionality to manage neighbor discovery requests in MyMesh.
This includes handling the status of requests, updating the state
upon transmission success or failure, and implementing a timeout
mechanism for neighbor discovery queries. The changes improve the
efficiency and reliability of neighbor discovery operations in
MQTT-enabled environments.
The room server never supported RX boosted gain, while the repeater
does. Three consequences on SX1262/SX1268 boards:
- boosted gain was never applied to the radio at boot, so a room server
ran in power-saving RX mode while an identical repeater ran boosted -
a real receive-sensitivity difference with nothing pointing at it
- _prefs.rx_boosted_gain was never initialised (the prefs are memset to
0 before defaults are set), so it defaulted to off
- 'set radio.rxgain on' replied "Error: unsupported" but CommonCLI had
already written the value to prefs and saved them, so a stale setting
survived reboot and was never applied
Mirror the repeater's implementation: initialise the pref default under
the same USE_SX1262/USE_SX1268 and SX126X_RX_BOOSTED_GAIN guards, apply
it during radio init, and override setRxBoostedGain() so the CLI reports
success and takes effect.
Built Heltec_v3_room_server (SX1262) and LilyGo_T3S3_sx1276_room_server
(guards compile out cleanly).
Implement SNMP functionality in MyMesh to provide radio diagnostics
and statistics updates. This includes a new method for formatting
radio diagnostic replies and periodic updates to the SNMP agent
with radio stats, enhancing monitoring capabilities for users
with SNMP enabled.
Add functionality to schedule deferred OTA updates in the MyMesh class.
This includes a new member variable to track the update time and a method
to initiate the update process, allowing for a smoother OTA experience
by managing timing and state transitions effectively.
Cherry-picked from observer-firmware (76f44d7d). Resolved a conflict in
loop() where the WITH_WEBCONFIG block occupies the same anchor and shares
an identical closing tail; both blocks retained.
Add support for neighbor discovery and management in the MyMesh class.
This includes structures for neighbor information, methods for handling
neighbor advertisements, and control data reception. The new features
allow for dynamic neighbor management, enhancing the mesh network's
capabilities. Additionally, the maximum number of neighbors is set to
50 across various platform configurations.
The 2026-07-19 upstream merge auto-merged two additions into the same class
bodies without conflicting, producing duplicate declarations:
examples/simple_room_server/MyMesh.h - getCADEnabled()
variants/heltec_v4/HeltecV4Board.h - setLoRaFemLnaEnabled(),
canControlLoRaFemLna(),
isLoRaFemLnaEnabled()
Same class of breakage as the RadioLibWrapper::_cad_enabled and
MyMesh::getCADEnabled() duplicates already fixed in the merge commit. These
survived because the merge was validated with the two prescribed MQTT smoke
builds, and neither of them compiles simple_room_server or the heltec_v4
variant - so CI was the first thing to touch the broken files.
Now verified across ALL 32 observer envs locally, not a sample: 32/32 build.
First upstream merge since the 2026-06-06 base (191 upstream commits). 14 files
conflicted; resolutions below.
Fleet-critical check (Constraint 1): upstream reordered NodePrefs members
(rx_boosted_gain / path_hash_mode moved to the struct tail) but did NOT change
/com_prefs. Persistence is written field-by-field at explicit offsets, so member
order is in-memory only. Verified the fork's writeCommonPrefsImage() is
byte-identical to upstream's inline writer at every offset (79 pad, 121, 122,
290-294). No migration needed.
Resolutions:
- CommonCLI.h: kept the fork's NodePrefs (superset) and adopted upstream's
setRxBoostedGain(bool)->bool signature change, which CommonCLI.cpp now uses to
report unsupported. Corrected a stale comment claiming rx_boosted_gain lives at
offset 79 (it is a pad; the field is at 290).
- CommonCLI.cpp: kept the fork's legacy /com_prefs migration and the extracted
writeCommonPrefsImage() call.
- UITask.cpp: three-way merge - upstream's drawTextCentered + powering-off
screen, plus the fork's WITH_WEBCONFIG portal/reboot screens.
- ESP32Board.cpp, MeshCore.h, platformio.ini: kept both sides (fork OTA additions
alongside upstream powerOff/enterDeepSleep and Packet.cpp).
- MicroNMEALocationProvider.h: took upstream's claim/release and added the
_claims member they depend on.
- MyMesh.cpp/.h (repeater + room server): kept the fork's superset defaults.
- Removed duplicate declarations auto-merge produced: RadioLibWrapper::_cad_enabled
and MyMesh::getCADEnabled().
Verification: native suite 15/15 (incl. upstream's new test_mesh_tables), both
MQTT smoke builds green, ArduinoJson pin check passes. Hardware validation next.
Introduce a web configuration portal for easier node management and
provisioning without serial CLI. Enhance MQTT functionality with
improved IATA code validation, dynamic slot management, and
background NTP synchronization. Update web UI elements for better
user experience and security notes regarding open AP usage.
Load-testing the restored token bucket at 'set dutycycle 1' showed MQTT
capture dropping to exactly the TX rate. Queued retransmissions hold static-
pool packets with no expiry, so throttling parks the whole pool in the send
queue; Dispatcher::checkRecv() then discards received packets before logRx()
ever feeds the bridge — each completed TX frees exactly one packet for
exactly one more RX.
Observer builds now use RxReservePacketManager (fork-owned header): once the
free pool drops below a quarter of the pool, outbound packets are refused and
freed, so RX allocation and MQTT capture continue at full rate while the node
sheds repeat load it has no TX budget for anyway. Non-observer builds keep
upstream pool behavior via the same factory; StaticPoolPacketManager stays
byte-identical to upstream.
Completes the FEM RX-gain restoration begun in the CAD/prefs change, which
persisted radio_fem_rxgain but didn't yet drive the hardware. Also dropped
by the 22eb9b87 revert; restored to match upstream.
- MainBoard: setLoRaFemLnaEnabled()/canControlLoRaFemLna()/isLoRaFemLnaEnabled()
virtuals (default: can't control — non-FEM boards report unsupported)
- heltec_v4: board overrides driving loRaFEMControl; LoRaFEMControl gains the
isLNAEnabled() getter (it already tracked lna_enabled and drove the FEM)
- CLI: `set radio.fem.rxgain on/off` / `get radio.fem.rxgain` (guarded by
canControlLoRaFemLna, so it reports "unsupported" on non-FEM boards)
- app startup applies the persisted pref: board.setLoRaFemLnaEnabled(
_prefs.radio_fem_rxgain), beside setRxBoostedGainMode
Default is ON (upstream), so on FEM boards the LNA is enabled after upgrade —
a real reception behavior change to confirm on hardware. The other FEM
variants (heltec_t096/tower_v2/tracker_v2) need the same small board-override
addition; until then `radio.fem.rxgain` reports unsupported there (no
regression — status quo).
Builds: heltec_v4 repeater-observer + room-observer (FEM board), Heltec_v3
repeater (non-FEM, base virtuals no-op). NEEDS on-device validation on a
Heltec V4.
Continues restoring features dropped by the 22eb9b87 revert. Both were
upstream-tested code, not intentional fork removals.
CAD (hardware Channel Activity Detection / listen-before-talk before TX),
fully restored and functional:
- NodePrefs.cad_enabled + `set cad on/off` / `get cad` CLI (default off)
- RadioLibWrapper: _cad_enabled + setCADEnabled() + the scanChannel()/CAD
branch in isChannelActive() (Phase 1 already restored the Dispatcher hook)
- getCADEnabled() overrides in the repeater/room/sensor apps (return the
pref) and companion (always on, matching upstream)
radio_fem_rxgain: the NodePrefs field + /com_prefs persistence are restored
here at upstream's exact offsets (293 fem, 294 cad), which makes /com_prefs
byte-identical to upstream through the tail. The field is persisted and
defaults on (upstream default), but the per-board LNA *driving* + the
`radio.fem.rxgain` CLI are deferred to the FEM-hardware change (they depend
on board methods and want per-board bench testing).
The new-format /com_prefs tail grows from 3 to 5 bytes; the old-format
detection threshold and the host migration harness are updated accordingly
(all scenarios pass, incl. the non-MQTT-build variant).
Builds: Heltec_v3 repeater, repeater-observer, room-observer. (sensor /
plain-room / companion fail only on the pre-existing Timezone.h include
issue, unrelated to these changes.)
The `recv_pkt_region` is set when processing a flood packet in `filterRecvFloodPacket`
but direct/non-flood packets would never pass through that function, so the pointer was
not cleared for them.
`sendFloodReply` would then later use it blindly, which meant that the response would
either inherit the region from the last flood packet, or refer to a non-initialised pointer
if no region floods had been received yet.
Refactored the handling of observer-related settings by moving them from
NodePrefs to a new MQTTPrefs structure. This change centralizes MQTT,
WiFi, timezone, SNMP, and alert configurations, improving code organization
and maintainability. The new structure allows for better separation of
concerns and prepares the codebase for future enhancements.
Implemented new commands for configuring and diagnosing NTP server
settings in the MQTT bridge. Users can now set a custom NTP server
and probe connectivity to configured servers. This enhancement
improves time synchronization reliability for JWT authentication
and provides better diagnostics for NTP connectivity issues.
agessaman