thinknode_m6: initial port

variants/thinknode_m6/ThinkNodeM6Board.cpp

@@ -0,0 +1,95 @@
+#include "ThinkNodeM6Board.h"
+#include <Arduino.h>
+
+#ifdef THINKNODE_M6
+
+#include <Wire.h>
+#include <bluefruit.h>
+
+static BLEDfu bledfu;
+
+static void connect_callback(uint16_t conn_handle) {
+  (void)conn_handle;
+  MESH_DEBUG_PRINTLN("BLE client connected");
+}
+
+static void disconnect_callback(uint16_t conn_handle, uint8_t reason) {
+  (void)conn_handle;
+  (void)reason;
+
+  MESH_DEBUG_PRINTLN("BLE client disconnected");
+}
+
+void ThinkNodeM6Board::begin() {
+  // for future use, sub-classes SHOULD call this from their begin()
+  startup_reason = BD_STARTUP_NORMAL;
+
+  Wire.begin();
+
+#ifdef P_LORA_TX_LED
+  pinMode(P_LORA_TX_LED, OUTPUT);
+  digitalWrite(P_LORA_TX_LED, LOW);
+#endif
+
+  delay(10); // give sx1262 some time to power up
+}
+
+uint16_t ThinkNodeM6Board::getBattMilliVolts() {
+  int adcvalue = 0;
+
+  digitalWrite(PIN_ADC_CTRL, HIGH);
+  analogReference(AR_INTERNAL_3_0);
+  analogReadResolution(12);
+  delay(10);
+
+  // ADC range is 0..3000mV and resolution is 12-bit (0..4095)
+  adcvalue = analogRead(PIN_VBAT_READ);
+  digitalWrite(PIN_ADC_CTRL, LOW);
+  // Convert the raw value to compensated mv, taking the resistor-
+  // divider into account (providing the actual LIPO voltage)
+  return (uint16_t)((float)adcvalue * REAL_VBAT_MV_PER_LSB);
+}
+
+bool ThinkNodeM6Board::startOTAUpdate(const char *id, char reply[]) {
+  // Config the peripheral connection with maximum bandwidth
+  // more SRAM required by SoftDevice
+  // Note: All config***() function must be called before begin()
+  Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
+  Bluefruit.configPrphConn(92, BLE_GAP_EVENT_LENGTH_MIN, 16, 16);
+
+  Bluefruit.begin(1, 0);
+  // Set max power. Accepted values are: -40, -30, -20, -16, -12, -8, -4, 0, 4
+  Bluefruit.setTxPower(4);
+  // Set the BLE device name
+  Bluefruit.setName("THINKNODE_M1_OTA");
+
+  Bluefruit.Periph.setConnectCallback(connect_callback);
+  Bluefruit.Periph.setDisconnectCallback(disconnect_callback);
+
+  // To be consistent OTA DFU should be added first if it exists
+  bledfu.begin();
+
+  // Set up and start advertising
+  // Advertising packet
+  Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
+  Bluefruit.Advertising.addTxPower();
+  Bluefruit.Advertising.addName();
+
+  /* Start Advertising
+    - Enable auto advertising if disconnected
+    - Interval:  fast mode = 20 ms, slow mode = 152.5 ms
+    - Timeout for fast mode is 30 seconds
+    - Start(timeout) with timeout = 0 will advertise forever (until connected)
+
+    For recommended advertising interval
+    https://developer.apple.com/library/content/qa/qa1931/_index.html
+  */
+  Bluefruit.Advertising.restartOnDisconnect(true);
+  Bluefruit.Advertising.setInterval(32, 244); // in unit of 0.625 ms
+  Bluefruit.Advertising.setFastTimeout(30);   // number of seconds in fast mode
+  Bluefruit.Advertising.start(0);             // 0 = Don't stop advertising after n seconds
+
+  strcpy(reply, "OK - started");
+  return true;
+}
+#endif