- Wio Tracker L1 1W no longer advertises TX gain control: its setter
drives LORA_PWR_EN, the shared LDO for the SX1262 and the PA, so
"gain off" would power down the radio.
- A SetFemState that arrives mid-TX is now applied after TxDone is
queued, so its reply follows TxDone.
- SetFemState replies (immediate or deferred) are retained until they
fit in the host output queue instead of being dropped, so a change
that took effect is always acknowledged.
- GetFemState replies queue behind an outstanding SetFemState reply;
a further SetFemState returns TxBusy until it clears.
Add SetHardware sub-commands so a host can probe and configure
per-board RF front-end settings:
- GetCapabilities (0x1B): uint32 feature bits (AGC, FEM RX, FEM TX)
- Set/GetAgcResetInterval (0x1C/0x1D): 0-1020 s, 4 s resolution,
0 disables; default stays 30 s
- Set/GetFemState (0x1E/0x1F): apply/value masks for FEM RX (LNA)
and TX (PA) gain; all-or-nothing, Unsupported (0x08) if any
requested bit is not controllable on this board
The AGC scheduler moves from main.cpp into KissModem so it is
configurable and unit-tested. FEM changes that arrive mid-TX are
deferred until the packet ends, since board setters drive FEM pins
directly.
MainBoard gains virtual FEM hooks (canControl/set/is for LNA and PA
gain). Boards that already implemented these methods privately now
expose them as overrides: Heltec V4, V4 R8, T096, Tracker V2,
Station G3 and Wio Tracker L1 1W.
KISS_FIRMWARE_VERSION bumped to 2.
Today if a user builds firmware with an incorrect WiFi SSID or password,
they get a generic `WiFi disconnected.` error message.
Extend logging to descirbe the reason that WiFi was disconnected.
I gathered the updated logs for the 3 scenarios below.
```
WiFi: Attempting manual WiFi reconnect...
WiFi: WiFi disconnected (reason=ASSOC_LEAVE). Flagging for reconnect...
WiFi: WiFi disconnected (reason=4WAY_HANDSHAKE_TIMEOUT). Flagging for reconnect...
WiFi: WiFi disconnected (reason=4WAY_HANDSHAKE_TIMEOUT). Flagging for reconnect...
WiFi: WiFi disconnected (reason=4WAY_HANDSHAKE_TIMEOUT). Flagging for reconnect...
```
```
WiFi: WiFi disconnected (reason=NO_AP_FOUND). Flagging for reconnect...
```
```
WiFi: WiFi connected successfully!
WiFi: Got connection
```
Payloads of 166 or 167 bytes previously passed the frame-sized bound
(MAX_CHANNEL_DATA_LENGTH = 167) but were rejected by sendGroupData
against MAX_GROUP_DATA_LENGTH (165), causing ERR_CODE_TABLE_FULL (retry
later) to be returned instead of ERR_CODE_ILLEGAL_ARG.
Fixes#3345
- scope the serial config CLI to RP2040; it was exposing the rescue CLI
(cat/rm/erase) on every ESP32 WiFi build, which gates it behind a
physical long-press
- bound and space out RP2040 rejoins: the core's join busy-waits, so cap
it at 5s and retry every 30s instead of every 10s
- stamp the reconnect timer in setup(), so the first loop() doesn't tear
down an association that is still finishing DHCP
- treat stored credentials as a pair, and pass NULL (not "") for an open
network
- teach build_as_lib.py where SerialWifiInterface moved
arduino-pico's WiFi.begin() blocks for up to 2x its 15s timeout, which
stalled the mesh loop on every reconnect attempt; use beginNoBlock().
Log the IP when the link comes up, and the status code when retrying.
Store ssid/pwd in NodePrefs and set them with 'set wifi.ssid' /
'set wifi.pwd' over USB serial; build-time WIFI_SSID/WIFI_PWD stay as
the fallback. Headless WiFi builds get the config CLI on Serial, which
is otherwise unused there.
SerialWifiInterface has no ESP32-specific code, so move it to
helpers/wifi and reuse it on RP2040. Guard the ESP32-only WiFi
event/auto-reconnect calls and poll link state on RP2040 instead.