Commit Graph
16 Commits
Author SHA1 Message Date
agessaman 9235d761da kiss_modem: keep FEM replies ordered and deliverable; drop Wio FEM control
- Wio Tracker L1 1W no longer advertises TX gain control: its setter
  drives LORA_PWR_EN, the shared LDO for the SX1262 and the PA, so
  "gain off" would power down the radio.
- A SetFemState that arrives mid-TX is now applied after TxDone is
  queued, so its reply follows TxDone.
- SetFemState replies (immediate or deferred) are retained until they
  fit in the host output queue instead of being dropped, so a change
  that took effect is always acknowledged.
- GetFemState replies queue behind an outstanding SetFemState reply;
  a further SetFemState returns TxBusy until it clears.
2026-09-23 16:11:29 -07:00
agessaman 5527a26f9a kiss_modem: add AGC reset interval and FEM gain control (protocol v2)
Add SetHardware sub-commands so a host can probe and configure
per-board RF front-end settings:

- GetCapabilities (0x1B): uint32 feature bits (AGC, FEM RX, FEM TX)
- Set/GetAgcResetInterval (0x1C/0x1D): 0-1020 s, 4 s resolution,
  0 disables; default stays 30 s
- Set/GetFemState (0x1E/0x1F): apply/value masks for FEM RX (LNA)
  and TX (PA) gain; all-or-nothing, Unsupported (0x08) if any
  requested bit is not controllable on this board

The AGC scheduler moves from main.cpp into KissModem so it is
configurable and unit-tested. FEM changes that arrive mid-TX are
deferred until the packet ends, since board setters drive FEM pins
directly.

MainBoard gains virtual FEM hooks (canControl/set/is for LNA and PA
gain). Boards that already implemented these methods privately now
expose them as overrides: Heltec V4, V4 R8, T096, Tracker V2,
Station G3 and Wio Tracker L1 1W.

KISS_FIRMWARE_VERSION bumped to 2.
2026-09-23 15:43:01 -07:00
Michael Graff d33fb4e9a7 Fix config parser aborting on an empty object
'custom:{}' (a DynamicConfigSerializer with nothing set) hits EXPECT_KEY
with a '}' and returns TOK_ERROR, so loadSerial stops there and silently
drops every property after it. Nothing follows 'custom' in NodePrefs
today, so it goes unnoticed until you add one.

Also include stdlib.h, which Arduino.h was providing on-device but not
in the native test build.
2026-09-05 23:15:13 -05:00
Scott Powell 8ccc9928a8 * DynamicConfigSerializer fixes, and unit tests 2026-08-24 19:42:55 +10:00
Scott Powell e78bff0041 * unit test no longer valid 2026-08-14 16:42:54 +10:00
ripplebiz b09cb27a1f Merge pull request #3106 from ViezeVingertjes/fix/scoped-reply-routing
Fix replies dropped when flood.max.unscoped is low
2026-08-13 15:00:37 +10:00
agessaman e2aa7b98f9 feat(companion_radio): add external FEM gain preferences for RX and TX for companions
Introduced consistent preferences for external LoRa FEM RX and TX gain settings in NodePrefs. Updated companion MyMesh to apply these settings during initialization and transmission. Added unit tests to verify the round-trip serialization of these new preferences.
2026-08-10 11:59:26 -07:00
ViezeVingertjes fad11c90f3 Fix replies dropped when flood.max.unscoped is low 2026-08-03 22:57:12 +02:00
ripplebiz 57ddada3ba Merge pull request #3004 from axhoff/agent/preserve-utf8-advert-names
Preserve UTF-8 boundaries in advert names
2026-07-30 12:59:59 +10:00
Scott Powell ee79df4c4f Merge branch 'dev' into config-serializer
# Conflicts:
#	test/mocks/Arduino.h
#	test/mocks/Stream.h
2026-07-24 15:06:48 +10:00
Alexander Hoffer 79dc1de6fc fix: preserve UTF-8 advert names 2026-07-20 15:47:03 +01:00
ViezeVingertjes fb2c61f862 fix: prevent ESP32 KISS modem stalls under USB backpressure
Switch ESP32-S3 KISS modem environments to HWCDC and move outbound KISS writes to a non-blocking queued frame path so loop() and TX completion keep progressing when the host reads slowly. Add native backpressure regression tests and correct the native_kiss_modem test filter so this suite runs directly with pio test.
2026-07-18 22:43:55 +02:00
Scott Powell d9f1e12b21 * loadSerial(), support for \n and \r 2026-07-17 21:23:40 +10:00
Scott Powell ae2667ee9e * added unit tests for ConfigSerializer 2026-07-17 20:55:30 +10:00
Christoph Koehler 4f701b7aec refactor: split MeshTables::hasSeen into pure query + markSeen
hasSeen() was simultaneously a predicate and a mutator — it inserted the
packet hash on every miss, making five call sites that only wanted to mark
a packet as sent call it with the return value discarded.

Split into:
- wasSeen()   — pure predicate, no side effects
- markSeen()  — explicit insert

All query sites now call markSeen() immediately after wasSeen() returns
false, preserving identical runtime behaviour. The five mark-only send
sites (sendFlood, sendDirect, sendZeroHop x2) now call markSeen directly.

Also fixes three bridge sites (BridgeBase, ESPNowBridge, RS232Bridge)
that had the same query+implicit-insert pattern.

Tests: add test/test_mesh_tables/ covering wasSeen purity, markSeen,
dup stats, and clear. Update SHA256 mock to produce deterministic output
(previously finalize() was a no-op). Add Packet.cpp to native build filter.
2026-07-01 21:51:38 -06:00
Michael Lynch 5e03c00397 Add unit tests for Utils::toHex 2026-04-24 19:37:21 +00:00