The major rev from 19.x to 20.x breaks Radiolab, so pin it for now. This should fix the failing wio-e5-mini_repeater builds.
ltoa is removed upstream, so it was replaced with snprintf. The p[] buffer is always 16 bytes. Copy/paste for why claude thinks this is fine below, but also if this is broken it wouldn't be new.
```
exp2 in [23, 30] (int_part = mantissa << (exp2 - 23)): this is where int_part can reach its true max, up to 2,147,483,520 — 10 digits. That's what the snprintf bound of 11 (10 digits + NUL) is sized for. But in this branch frac_part is never assigned anything other than its initial 0, so only *p++ = '0' runs for the fraction — 1 char, not 7.
exp2 in [0, 22] (int_part = mantissa >> (23 - exp2)): this is the only branch where frac_part can also be nonzero and enter the 7-digit loop. Here int_part < 2^23 by construction, so it's capped at 7 digits, never 10.
```
One nRF52840 variant shared across both radios, picked per env: Duo runs
the LR1121, Uno the SX1262. Same PCB, only the radio and its DIO1 pin
change.
SuperIO adds the SH1107 OLED, GPS, buzzer and joystick. GPS is driven by
the 3-position mode switch (Mode 2 = on), polled live the way thinknode_m1
does it.
Five quick user-button presses power the unit off; a press wakes it back
on (arms the button as an nRF52 GPIO SENSE source before SYSTEMOFF).
Consolidates #2054 and andyshinn's shared-base/uno work, rebased on dev.
Co-authored-by: lbibass <ewdries02@gmail.com>
Co-authored-by: Andy Shinn <andys@andyshinn.as>
'custom:{}' (a DynamicConfigSerializer with nothing set) hits EXPECT_KEY
with a '}' and returns TOK_ERROR, so loadSerial stops there and silently
drops every property after it. Nothing follows 'custom' in NodePrefs
today, so it goes unnoticed until you add one.
Also include stdlib.h, which Arduino.h was providing on-device but not
in the native test build.
SerialWifiInterface has no ESP32-specific code, so move it to
helpers/wifi and reuse it on RP2040. Guard the ESP32-only WiFi
event/auto-reconnect calls and poll link state on RP2040 instead.
Lets applications know whether a GPS was actually detected
(EnvironmentSensorManager reports its gps_detected state), e.g. to
hide GPS-dependent UI when no receiver is attached.
An unconfigured slot has an all-zero secret, so it matches null-key group traffic (a sender with an unset PSK). The zero-key MAC validates against the empty slot and the foreign message is delivered as if it belonged to that channel — every node with a free slot is a null-key sink. Skip empty slots.
thinknode_m8: initial support
adds some functionalities to ui_task and epddisplay:
epd display,
- supports screen off, and clear screen
- supports forcing full refresh every N partial refreshes (off by default, configured to 60 for M8)
ui_task
- UI_SHOW_CLOCK flag to display clock on first screen
- rotary button can act like joystick (with regards to Enter key), defaults to old config for existing nodes
- screen off on long press when using rotary button (very handy for the watch)
Grove and other Bosch modules strap SDO high, so the 0x76-only table
never initialized them. Add an alternate-address entry per Bosch sensor;
the bus scan still gates every probe, and all four drivers verify a chip
ID before claiming an address.
Each sensor type has a single static driver instance, so skip an entry
whose query is already active: the alternate address is a fallback, not
a second device.
ripplebiz