Olexandr Tyshchenko
cbfa66df9d
NmeaGpsDriver: baud rates to probe come from the board, not a build flag
2026-11-09 22:59:47 +02:00
Martin Boissonneault
666949fae4
rak4631: let the serial GPS switch the WB_IO2 rail (opt-in)
...
On a RAK19007 the RAK12501's supply is 3V3_S, switched by WB_IO2, so
gps off, periodic mode and shutdown left it powered. Pass WB_IO2 to the
NMEA driver as peripheralPower under GPS_RAIL_POWER_CONTROL, set by the
new RAK_4631_repeater_gps_power env. It is opt-in because the rail feeds
every slot module, and refused with ETHERNET_ENABLED (RAK13800).
The RAK12500 (I2C) driver keeps switching its own power pin, so this
only applies on the NMEA path.
RefCountedDigitalPin now sets OUTPUT on claim and release: WB_IO2 left
as an input (as probeRak12500() leaves it after a failed probe) keeps
3V3_S in its last state, so writing the latch alone did not cut it.
Measured with a KM003C, battery and panel out: gps off 40.5 -> 12.4 mA,
shutdown 29.7 -> 1.30 mA.
2026-11-08 08:47:35 -04:00
Florent
d71a418748
gps: serial pin and configuration fixes (nrf52, meshadventurer, tracker_v1, heltec_tracker)
2026-11-08 08:47:34 -04:00
Níckolas Goline
22ce208e68
muzi_base: fix GPS UART pins and re-enable ATGM336H NMEA output
...
The refactor no longer calls Serial1.setPins() on nRF52, so Serial1 uses
PIN_SERIAL1_RX/TX directly. Those were swapped (the GPS transmits on
P0.20), so no data was received. Fix them and define PIN_GPS_TX/RX by the
gps module's side, as other variants do.
The ATGM336H keeps its NMEA output config across power cycles, and other
firmware may leave every sentence disabled. Re-enable GGA + RMC after each
power-up.
2026-11-08 08:47:34 -04:00
Florent
3fd36e7ac6
gps: adapt ui-new and the sensor managers
2026-11-08 08:47:34 -04:00
Florent
fa7ca3f418
rak_gps: simplify the rak driver, which now only handles i2c, for nmea use nmea driver directly
2026-11-08 08:47:34 -04:00
Florent
fe6a47d0c9
gps: move the gps CLI to GpsPrefs and convert all targets
2026-11-08 08:47:34 -04:00
Florent
df5a768c5d
gps: add GpsDriver, handle the hardware and software switches in the drivers
2026-11-08 08:47:34 -04:00
fdlamotte
04d72b1049
Merge pull request #3687 from fdlamotte/display_prefs
...
ui: add some parameters to the cli (mostly regarding eink behaviour)
2026-10-29 08:35:36 -04:00
Florent
5d7100ae7d
ui: add some parameters to the cli (mostly regarding eink behaviour)
2026-10-29 08:34:41 -04:00
Florent
cedb8050a5
Remove unused buttonStateChanged from some variants
2026-10-27 15:52:36 -04:00
akalinin-softvelum
492814bbef
T-Echo: use GxEPD2_154_D67 e-ink driver
...
T-Echo used the fallback GxEPD2_150_BN; on my unit every refresh hit the
10 s busy timeout. Switch to GxEPD2_154_D67 like Meshtastic.
2026-10-27 18:20:36 +00:00
fdlamotte
afa4b87c6c
Merge pull request #3509 from marcelverdult/fix/thinknode-m8-sensors
...
Fix ThinkNode M8 repeater/room server build: compile sensor helpers for all envs
2026-10-27 09:31:51 -04:00
Florent
2cad4eecb4
ThinknodeM5: enable wifi in usb companion
2026-10-25 17:49:16 -04:00
fdlamotte
ea8e95447f
Merge pull request #3659 from fdlamotte/elecrow_eink_refactor
...
Elecrow eink refactor
2026-10-24 19:50:03 -04:00
Florent
b2106ea7ee
ThinknodeM1: update eink driver
2026-10-24 13:26:06 -04:00
Florent
d7c0eadbe2
thinknode_m1: fix button2 definition
2026-10-24 11:15:28 -04:00
Florent
408d674ace
DisplayDriver: fixing alignment issue in vtable for nrf52 and epd display
2026-10-21 17:13:27 -04:00
Florent
a31e2c92df
refactoring eink devices behaviour
2026-10-21 14:08:56 -04:00
liamcottle
87c76a8b06
implement new auto detect display for sh1106 and ssd1306
2026-10-21 15:41:11 +13:00
Liam Cottle
dec8ad6edc
Merge pull request #3614 from amdoolittle/fix/heltec-v4-tft-wifi-enable
...
Fix: Added WiFi to TFT BLE version of Heltec V4
2026-10-21 13:59:37 +13:00
Radek
933c0f6a98
added dynamic wifi to: lilygo t-beam supreme sx1262 ble companion
2026-10-18 11:02:07 +02:00
amdoolittle
9d93a72693
Added WiFi to TFT BLE version of Heltec V4
2026-10-16 22:39:26 -07:00
Rastislav Vysoky
97c0aec8d6
added dynamic wifi to: heltec wsl3, v4r8, wireless paper; rak 3112; xiao s3 (wio)
2026-10-15 09:57:31 +02:00
ripplebiz
f1b608a777
Merge pull request #2377 from fschrempf/dev
...
Disable NRF52 undervoltage bootlock feature
2026-10-15 15:02:12 +11:00
Liam Cottle
2586f7abe3
Merge pull request #3591 from liamcottle/feature/companion-ble-wifi
...
Add WiFi support to Heltec v3 and v4 BLE variants
2026-10-14 20:23:11 +13:00
liamcottle
c0d00a060a
enable wifi interface for heltec v4 ble variant
2026-10-14 15:16:55 +13:00
liamcottle
590bc23ab9
enable wifi interface for heltec v3 ble variant
2026-10-14 15:05:00 +13:00
agessaman
3d1a5d4c64
feat(variants): add Waveshare ESP32-S3-LR1121
...
ESP32-S3FH4R2 (4MB flash, 2MB PSRAM, native USB-CDC) with an LR1121.
Pins, the DIO5/DIO6 RF switch table and the 1.8 V TCXO follow the HF
schematic and Waveshare's examples. Envs: repeater, room server,
companion USB/BLE and KISS modem, all on min_spiffs so roles share one
partition layout.
Only RFO_HP_LF is wired (R4 on RFO_LP_LF is not fitted), so the new
opt-in LR1121_FORCE_HP_PA flag keeps RadioLib on the HP PA at <= 14 dBm,
where it would otherwise select the unconnected LP PA.
2026-10-11 20:51:18 -07:00
Sebastian Muszynski
4c2af58d3e
Use consistent _OTA suffix for nRF52 OTA BLE names
2026-10-06 18:50:15 +02:00
Huw Duddy
a706d1d943
Revert "Fix Heltec Mesh Node T1 GNSS pins"
2026-10-01 22:17:44 +10:00
Huw Duddy
914143cb7e
Merge pull request #3411 from Avamander/patch-3
...
Fix Heltec Mesh Node T1 GNSS pins
2026-10-01 20:31:38 +10:00
Huw Duddy
2ce37ec8cc
Merge branch 'dev' into fix-t1000e-sensor-power-pin
2026-10-01 19:57:50 +10:00
Huw Duddy
bbe54f8c55
Merge pull request #2719 from jirogit/fix/techo-lite-flash-device
...
fix(techo-lite): remove duplicate EXTERNAL_FLASH_DEVICES definition
2026-10-01 00:41:23 +10:00
Huw Duddy
79e309365f
Merge pull request #3001 from Szetya/patch-1
...
Fix T-Echo Lite GPS pins
2026-10-01 00:38:23 +10:00
Huw Duddy
77396d0538
Merge pull request #3301 from beala/beala/fix-t1-clock
...
Fix clock on Heltec T1: Do not misidentify IMU as an RTC
2026-09-30 23:46:32 +10:00
Huw Duddy
884391447c
Merge pull request #3155 from TadyTheFish/enable-ina226-promicro
...
Enable INA226 support for ProMicro nRF52840
2026-09-30 23:23:35 +10:00
ripplebiz
5846fa19c8
Merge pull request #3525 from oltaco/airoha-sleep
...
Use Airoha AG3335 backup mode sleep for faster GPS fix time
2026-09-30 12:32:44 +10:00
Huw Duddy
33468c4f80
Merge pull request #2472 from emkZero/variant-techo-lite-usb-companion
...
variants: USB Companion variant for LilyGo T-Echo Lite
2026-09-29 23:00:41 +10:00
taco
74413f0e4d
T1000e GPS: use RTC backup for faster fix
2026-09-29 20:16:32 +10:00
taco
11755c8199
MeshTracker X1 GPS: use RTC backup for faster fix
2026-09-29 20:14:19 +10:00
Liam Cottle
db7a5f942f
Merge pull request #3508 from marcelverdult/fix/rak11310-attach-dynamic-prefs
...
Fix RAK11310 build: add no-op attachDynamicPrefs()
2026-09-27 20:03:59 +13:00
Marcel Verdult
f99ea79b36
Fix ThinkNode M8 repeater/room server build: compile sensor helpers for all envs
2026-09-26 20:39:23 +02:00
fdlamotte
1934a4988d
Merge pull request #3202 from F4FPR/m6-power-observability
...
ThinkNode M6: expose external-power and charger state
2026-09-26 13:51:11 -04:00
Marcel Verdult
d07803bd9b
Fix RAK11310 build: add no-op attachDynamicPrefs()
2026-09-26 14:07:28 +02:00
liamcottle
aa1c46e1db
disable hibernate ui on 1watt wio tracker variant
2026-09-25 16:55:17 +12:00
Liam Cottle
c423dece36
Merge pull request #3490 from liamcottle/fix/heltec-ct62
...
Fix Heltec CT62 boot loop
2026-09-23 17:48:04 +12:00
liamcottle
c13b312188
fix heltec ct62 boot loop
2026-09-23 15:04:51 +12:00
Wessel Nieboer
b5787757a7
Thinknode m4 - don't touch crystal and OTA name
2026-09-21 15:55:44 +02:00
Florent
8bf072a6f0
M4: Handle poweroff
2026-09-20 16:13:15 -04:00