Commit Graph
1302 Commits
Author SHA1 Message Date
Will MacGregorandClaude Opus 5 dd78cc35d2 Add variant for ST Nucleo-WL55JC1
Adds repeater, room_server, companion_radio_usb and kiss_modem
environments for the NUCLEO-WL55JC1 (STM32WL55JC, integrated SubGHz radio).

Notes on the board setup:

- Uses the upstream nucleo_wl55jc board. PlatformIO's boards_remap maps it
  to the core's NUCLEO_WL55JC1 variant, so the LEDs, user buttons and the
  LPUART1 -> ST-LINK VCP serial mapping all come from the core rather than
  being redefined here.
- The RF switch table is built from the core's LORAWAN_RFSWITCH_* macros
  (SP3T front end on PC3/PC4/PC5) so it tracks upstream if those are ever
  revised. Both RFO_LP and RFO_HP are registered, so RadioLib selects HP
  above 14 dBm and LP below it.
- board_build.extra_flags pins the device to STM32WL55xx. The stock board
  manifest declares product_line STM32WL55xx but extra_flags -DSTM32WLE5xx;
  that only works because every #elif chain happens to test WL55xx first.
- The Nucleo's LD1..LD3 are driven active HIGH, so the TX LED hooks are
  inverted relative to STM32Board's active-LOW default.
- 32 KB reserved at the top of flash for LittleFS, as on the other
  STM32WL variants.

Verified on hardware: all four environments build; repeater and room_server
flash and run over ST-LINK; identity and prefs persist across reboot and
across a firmware swap; and GPIOC reads back the documented RX levels at
idle, confirming the front-end switch is driven correctly.

Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
2026-11-04 09:46:40 -05:00
ripplebiz 26079dea9b Merge pull request #3599 from zxw19/feat/sensecap-solar-white-led
feat: Add low-power white status LED for SenseCAP Solar P1 Pro
2026-11-02 19:17:14 +11:00
zxw f9c54a1499 feat: Add low-power white status LED for SenseCAP Solar P1 Pro
Add a dimmed heartbeat for the SenseCAP Solar (P1 Pro) white LED in the
repeater firmware, implemented entirely as a SenseCapSolarBoard::loop()
override so no example main.cpp needs to be touched:

- 100 ms pulse every 5 s, dimmed to 10% brightness via hardware PWM
  (NRF_PWM0 / HwPWM0, 1 kHz, COUNTERTOP 16000, compare 1600)
- during the 4.9 s off phase the PWM peripheral is stopped (ENABLE=0),
  the pin is released (PSEL disconnect) and GPIO 11 is held LOW, so no
  HFCLK is demanded between pulses
- on successful application-level "start ota" the PWM is stopped and the
  white LED goes steady full-brightness while BLE OTA is advertised;
  on failed start the heartbeat keeps blinking
- powerOff() stops/releases the heartbeat PWM before shutting the LED off
- non-blocking millis() timing with wrap-safe unsigned arithmetic
- gated by SENSECAP_SOLAR_WHITE_LED, defined only in the
  SenseCap_Solar_repeater PlatformIO env, so the room-server and
  companion firmwares sharing this board class are unaffected

No changes to LoRa/repeater forwarding, the blue TX LED, charging LEDs,
GPS, power management, config storage or the bootloader.
2026-10-30 10:01:52 +08:00
fdlamotte 04d72b1049 Merge pull request #3687 from fdlamotte/display_prefs
ui: add some parameters to the cli (mostly regarding eink behaviour)
2026-10-29 08:35:36 -04:00
Florent 5d7100ae7d ui: add some parameters to the cli (mostly regarding eink behaviour) 2026-10-29 08:34:41 -04:00
Florent cedb8050a5 Remove unused buttonStateChanged from some variants 2026-10-27 15:52:36 -04:00
akalinin-softvelum 492814bbef T-Echo: use GxEPD2_154_D67 e-ink driver
T-Echo used the fallback GxEPD2_150_BN; on my unit every refresh hit the
10 s busy timeout. Switch to GxEPD2_154_D67 like Meshtastic.
2026-10-27 18:20:36 +00:00
fdlamotte afa4b87c6c Merge pull request #3509 from marcelverdult/fix/thinknode-m8-sensors
Fix ThinkNode M8 repeater/room server build: compile sensor helpers for all envs
2026-10-27 09:31:51 -04:00
Florent 2cad4eecb4 ThinknodeM5: enable wifi in usb companion 2026-10-25 17:49:16 -04:00
fdlamotte ea8e95447f Merge pull request #3659 from fdlamotte/elecrow_eink_refactor
Elecrow eink refactor
2026-10-24 19:50:03 -04:00
Florent b2106ea7ee ThinknodeM1: update eink driver 2026-10-24 13:26:06 -04:00
Florent d7c0eadbe2 thinknode_m1: fix button2 definition 2026-10-24 11:15:28 -04:00
Florent 408d674ace DisplayDriver: fixing alignment issue in vtable for nrf52 and epd display 2026-10-21 17:13:27 -04:00
Florent a31e2c92df refactoring eink devices behaviour 2026-10-21 14:08:56 -04:00
liamcottle 87c76a8b06 implement new auto detect display for sh1106 and ssd1306 2026-10-21 15:41:11 +13:00
Liam Cottle dec8ad6edc Merge pull request #3614 from amdoolittle/fix/heltec-v4-tft-wifi-enable
Fix: Added WiFi to TFT BLE version of Heltec V4
2026-10-21 13:59:37 +13:00
Radek 933c0f6a98 added dynamic wifi to: lilygo t-beam supreme sx1262 ble companion 2026-10-18 11:02:07 +02:00
amdoolittle 9d93a72693 Added WiFi to TFT BLE version of Heltec V4 2026-10-16 22:39:26 -07:00
Rastislav Vysoky 97c0aec8d6 added dynamic wifi to: heltec wsl3, v4r8, wireless paper; rak 3112; xiao s3 (wio) 2026-10-15 09:57:31 +02:00
ripplebiz f1b608a777 Merge pull request #2377 from fschrempf/dev
Disable NRF52 undervoltage bootlock feature
2026-10-15 15:02:12 +11:00
Liam Cottle 2586f7abe3 Merge pull request #3591 from liamcottle/feature/companion-ble-wifi
Add WiFi support to Heltec v3 and v4 BLE variants
2026-10-14 20:23:11 +13:00
liamcottle c0d00a060a enable wifi interface for heltec v4 ble variant 2026-10-14 15:16:55 +13:00
liamcottle 590bc23ab9 enable wifi interface for heltec v3 ble variant 2026-10-14 15:05:00 +13:00
agessaman 3d1a5d4c64 feat(variants): add Waveshare ESP32-S3-LR1121
ESP32-S3FH4R2 (4MB flash, 2MB PSRAM, native USB-CDC) with an LR1121.
Pins, the DIO5/DIO6 RF switch table and the 1.8 V TCXO follow the HF
schematic and Waveshare's examples. Envs: repeater, room server,
companion USB/BLE and KISS modem, all on min_spiffs so roles share one
partition layout.

Only RFO_HP_LF is wired (R4 on RFO_LP_LF is not fitted), so the new
opt-in LR1121_FORCE_HP_PA flag keeps RadioLib on the HP PA at <= 14 dBm,
where it would otherwise select the unconnected LP PA.
2026-10-11 20:51:18 -07:00
Sebastian Muszynski 4c2af58d3e Use consistent _OTA suffix for nRF52 OTA BLE names 2026-10-06 18:50:15 +02:00
Huw Duddy a706d1d943 Revert "Fix Heltec Mesh Node T1 GNSS pins" 2026-10-01 22:17:44 +10:00
Huw Duddy 914143cb7e Merge pull request #3411 from Avamander/patch-3
Fix Heltec Mesh Node T1 GNSS pins
2026-10-01 20:31:38 +10:00
Huw Duddy 2ce37ec8cc Merge branch 'dev' into fix-t1000e-sensor-power-pin 2026-10-01 19:57:50 +10:00
Huw Duddy bbe54f8c55 Merge pull request #2719 from jirogit/fix/techo-lite-flash-device
fix(techo-lite): remove duplicate EXTERNAL_FLASH_DEVICES definition
2026-10-01 00:41:23 +10:00
Huw Duddy 79e309365f Merge pull request #3001 from Szetya/patch-1
Fix T-Echo Lite GPS pins
2026-10-01 00:38:23 +10:00
Huw Duddy 77396d0538 Merge pull request #3301 from beala/beala/fix-t1-clock
Fix clock on Heltec T1: Do not misidentify IMU as an RTC
2026-09-30 23:46:32 +10:00
Huw Duddy 884391447c Merge pull request #3155 from TadyTheFish/enable-ina226-promicro
Enable INA226 support for ProMicro nRF52840
2026-09-30 23:23:35 +10:00
ripplebiz 5846fa19c8 Merge pull request #3525 from oltaco/airoha-sleep
Use Airoha AG3335 backup mode sleep for faster GPS fix time
2026-09-30 12:32:44 +10:00
Huw Duddy 33468c4f80 Merge pull request #2472 from emkZero/variant-techo-lite-usb-companion
variants: USB Companion variant for LilyGo T-Echo Lite
2026-09-29 23:00:41 +10:00
taco 74413f0e4d T1000e GPS: use RTC backup for faster fix 2026-09-29 20:16:32 +10:00
taco 11755c8199 MeshTracker X1 GPS: use RTC backup for faster fix 2026-09-29 20:14:19 +10:00
Liam Cottle db7a5f942f Merge pull request #3508 from marcelverdult/fix/rak11310-attach-dynamic-prefs
Fix RAK11310 build: add no-op attachDynamicPrefs()
2026-09-27 20:03:59 +13:00
Marcel Verdult f99ea79b36 Fix ThinkNode M8 repeater/room server build: compile sensor helpers for all envs 2026-09-26 20:39:23 +02:00
fdlamotte 1934a4988d Merge pull request #3202 from F4FPR/m6-power-observability
ThinkNode M6: expose external-power and charger state
2026-09-26 13:51:11 -04:00
Marcel Verdult d07803bd9b Fix RAK11310 build: add no-op attachDynamicPrefs() 2026-09-26 14:07:28 +02:00
liamcottle aa1c46e1db disable hibernate ui on 1watt wio tracker variant 2026-09-25 16:55:17 +12:00
Liam Cottle c423dece36 Merge pull request #3490 from liamcottle/fix/heltec-ct62
Fix Heltec CT62 boot loop
2026-09-23 17:48:04 +12:00
liamcottle c13b312188 fix heltec ct62 boot loop 2026-09-23 15:04:51 +12:00
Wessel Nieboer b5787757a7 Thinknode m4 - don't touch crystal and OTA name 2026-09-21 15:55:44 +02:00
Florent 8bf072a6f0 M4: Handle poweroff 2026-09-20 16:13:15 -04:00
Florent 0a15c487d8 m4: inital port 2026-09-20 15:25:18 -04:00
Liam Cottle 0886259701 Merge pull request #3108 from tjdownes/muzi-base
Add Muzi Base board support (Duo + Uno + SuperIO)
2026-09-20 22:56:32 +12:00
TJ Downes 114cf9f4fc Use the default BLE TX power on Muzi Base
Drop BLE_TX_POWER=0 from the companion envs so they use the default of
4 dBm, like most other variants. The lower power was carried over from
the original Base Duo PR and real-world range is better at the default.
2026-09-20 03:46:25 -07:00
TJ Downes 798ce636df Address review feedback on Muzi Base support
- rename the board class and files to MuziBaseBoard
- uppercase the build flags (MUZI_BASE, MUZI_BASE_SUPERIO)
- name the superIO envs muzi_base_{duo,uno}_superIO_companion_radio_ble so
  build.sh picks them up
- set MAX_CONTACTS to 350 like the other variants
- move the pin setup from initVariant() into MuziBaseBoard::begin()
2026-09-19 21:47:24 -07:00
liamcottle 4021a341f8 add wifi support to thinknode m7 ble variant 2026-09-20 15:11:21 +12:00