mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-10-24 08:22:37 +00:00
130 lines
4.1 KiB
C
130 lines
4.1 KiB
C
#ifndef _SEEED_WIO_TRACKER_L1_H_
|
|
#define _SEEED_WIO_TRACKER_L1_H_
|
|
|
|
/** Master clock frequency */
|
|
#define VARIANT_MCK (64000000ul)
|
|
|
|
#define USE_LFXO // Board uses 32khz crystal for LF
|
|
|
|
/*----------------------------------------------------------------------------
|
|
* Headers
|
|
*----------------------------------------------------------------------------*/
|
|
|
|
#include "WVariant.h"
|
|
|
|
#define PINS_COUNT (34)
|
|
#define NUM_DIGITAL_PINS (34)
|
|
#define NUM_ANALOG_INPUTS (8)
|
|
#define NUM_ANALOG_OUTPUTS (0)
|
|
|
|
// LEDs
|
|
#define PIN_LED (11)
|
|
#define LED_BLUE (-1) // Disable annoying flashing caused by Bluefruit
|
|
#define LED_BUILTIN PIN_LED
|
|
#define P_LORA_TX_LED PIN_LED
|
|
#define LED_STATE_ON 1
|
|
|
|
// Buttons
|
|
#define PIN_BUTTON1 (13) // Menu / User Button
|
|
#define PIN_BUTTON2 (25) // Joystick Up
|
|
#define PIN_BUTTON3 (26) // Joystick Down
|
|
#define PIN_BUTTON4 (27) // Joystick Left
|
|
#define PIN_BUTTON5 (28) // Joystick Right
|
|
#define PIN_BUTTON6 (29) // Joystick Press
|
|
#define PIN_BACK_BTN PIN_BUTTON1
|
|
#define JOYSTICK_UP PIN_BUTTON2
|
|
#define JOYSTICK_DOWN PIN_BUTTON3
|
|
#define JOYSTICK_LEFT PIN_BUTTON4
|
|
#define JOYSTICK_RIGHT PIN_BUTTON5
|
|
#define JOYSTICK_PRESS PIN_BUTTON6
|
|
#define PIN_USER_BTN PIN_BUTTON6
|
|
|
|
// Buzzer
|
|
// #define PIN_BUZZER (12) // Buzzer pin (defined per firmware type)
|
|
|
|
#define VBAT_ENABLE (30)
|
|
|
|
// Analog pins
|
|
#define PIN_VBAT_READ (16)
|
|
#define AREF_VOLTAGE (3.6F)
|
|
#define ADC_MULTIPLIER (2.0F)
|
|
#define ADC_RESOLUTION (12)
|
|
|
|
// Serial interfaces
|
|
#define PIN_SERIAL1_RX (7)
|
|
#define PIN_SERIAL1_TX (6)
|
|
|
|
// SPI Interfaces
|
|
#define SPI_INTERFACES_COUNT (2)
|
|
|
|
#define PIN_SPI_MISO (9)
|
|
#define PIN_SPI_MOSI (10)
|
|
#define PIN_SPI_SCK (8)
|
|
|
|
// BQ25616 single-wire charge status (Pro 1W)
|
|
#define PIN_BOOST_EN (31) // D31 / P0.13 鈥?Grove 5V Boost enable
|
|
#define EXT_CHRG_DETECT (32) // D32 / P1.15 鈥?BQ25616 STAT
|
|
#define EXT_CHRG_DETECT_VALUE LOW // 0 = charging, 1 = full / charger sleep
|
|
#define BOOST_EN_ACTIVE HIGH // HIGH enables Grove 5V Boost
|
|
|
|
// Lora Pins
|
|
#define P_LORA_SCLK PIN_SPI_SCK
|
|
#define P_LORA_MISO PIN_SPI_MISO
|
|
#define P_LORA_MOSI PIN_SPI_MOSI
|
|
#define P_LORA_DIO_1 (1)
|
|
#define P_LORA_RESET (2)
|
|
#define P_LORA_BUSY (3)
|
|
#define P_LORA_NSS (4)
|
|
#define SX126X_RXEN (5)
|
|
#define SX126X_TXEN RADIOLIB_NC
|
|
#define SX126X_DIO2_AS_RF_SWITCH true
|
|
#define SX126X_DIO3_TCXO_VOLTAGE (1.8f)
|
|
|
|
// LORA_PWR_EN (P0.14): external LDO enable for the SX1262 + 1 W PA on the Pro 1W board.
|
|
#define LORA_PWR_EN (33)
|
|
#define SX126X_POWER_EN LORA_PWR_EN
|
|
|
|
// Wire Interfaces
|
|
#define WIRE_INTERFACES_COUNT (2)
|
|
|
|
#define PIN_WIRE_SDA (14)
|
|
#define PIN_WIRE_SCL (15)
|
|
#define PIN_WIRE1_SDA (18)
|
|
#define PIN_WIRE1_SCL (17)
|
|
#define I2C_NO_RESCAN
|
|
#define DISPLAY_ADDRESS 0x3D // SH1106 OLED I2C address
|
|
|
|
// GPS L76KB
|
|
#define GPS_BAUDRATE 9600
|
|
#define PIN_GPS_TX PIN_SERIAL1_RX
|
|
#define PIN_GPS_RX PIN_SERIAL1_TX
|
|
#define PIN_GPS_STANDBY (0)
|
|
#define PIN_GPS_EN (PIN_GPS_STANDBY)
|
|
|
|
// QSPI Pins
|
|
#define PIN_QSPI_SCK (19)
|
|
#define PIN_QSPI_CS (20)
|
|
#define PIN_QSPI_IO0 (21)
|
|
#define PIN_QSPI_IO1 (22)
|
|
#define PIN_QSPI_IO2 (23)
|
|
#define PIN_QSPI_IO3 (24)
|
|
|
|
#define EXTERNAL_FLASH_DEVICES P25Q16H
|
|
#define EXTERNAL_FLASH_USE_QSPI
|
|
|
|
// // EInk on SPI1
|
|
// #define PIN_DISPLAY_CS (36)
|
|
// #define PIN_DISPLAY_BUSY (35)
|
|
// #define PIN_DISPLAY_DC (34)
|
|
// #define PIN_DISPLAY_RST (32)
|
|
|
|
#define PIN_SPI1_MISO (37)
|
|
#define PIN_SPI1_MOSI (33)
|
|
#define PIN_SPI1_SCK (31)
|
|
|
|
// GxEPD2 needs that for a panel that is not even used !
|
|
extern const int MISO;
|
|
extern const int MOSI;
|
|
extern const int SCK;
|
|
|
|
#endif |