mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-05-24 19:35:23 +00:00
Quency-D
136 lines
3.5 KiB
C++
136 lines
3.5 KiB
C++
#include "T1Board.h"
|
|
|
|
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
const PowerMgtConfig power_config = {
|
|
.lpcomp_ain_channel = PWRMGT_LPCOMP_AIN,
|
|
.lpcomp_refsel = PWRMGT_LPCOMP_REFSEL,
|
|
.voltage_bootlock = PWRMGT_VOLTAGE_BOOTLOCK
|
|
};
|
|
|
|
void T1Board::initiateShutdown(uint8_t reason) {
|
|
variant_shutdown();
|
|
|
|
bool enable_lpcomp = (reason == SHUTDOWN_REASON_LOW_VOLTAGE ||
|
|
reason == SHUTDOWN_REASON_BOOT_PROTECT);
|
|
pinMode(PIN_BAT_CTL, OUTPUT);
|
|
digitalWrite(PIN_BAT_CTL, enable_lpcomp ? ADC_CTRL_ENABLED : !ADC_CTRL_ENABLED);
|
|
|
|
if (enable_lpcomp) {
|
|
configureVoltageWake(power_config.lpcomp_ain_channel, power_config.lpcomp_refsel);
|
|
}
|
|
|
|
enterSystemOff(reason);
|
|
}
|
|
#endif
|
|
|
|
void T1Board::begin() {
|
|
NRF52Board::begin();
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
checkBootVoltage(&power_config);
|
|
#endif
|
|
|
|
#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
|
|
Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
|
|
#endif
|
|
Wire.begin();
|
|
|
|
pinMode(P_LORA_TX_LED, OUTPUT);
|
|
digitalWrite(P_LORA_TX_LED, !LED_STATE_ON);
|
|
|
|
pinMode(PIN_GPS_EN, OUTPUT);
|
|
digitalWrite(PIN_GPS_EN, !PIN_GPS_EN_ACTIVE);
|
|
|
|
pinMode(PIN_SENSOR_EN, OUTPUT);
|
|
digitalWrite(PIN_SENSOR_EN, PIN_SENSOR_EN_ACTIVE);
|
|
|
|
pinMode(PIN_BUZZER, OUTPUT);
|
|
digitalWrite(PIN_BUZZER, LOW);
|
|
pinMode(PIN_BUZZER_VOLTAGE_MULTIPLIER_1, OUTPUT);
|
|
pinMode(PIN_BUZZER_VOLTAGE_MULTIPLIER_2, OUTPUT);
|
|
digitalWrite(PIN_BUZZER_VOLTAGE_MULTIPLIER_1, HIGH);
|
|
digitalWrite(PIN_BUZZER_VOLTAGE_MULTIPLIER_2, HIGH);
|
|
|
|
periph_power.begin();
|
|
delay(1);
|
|
}
|
|
|
|
void T1Board::onBeforeTransmit() {
|
|
digitalWrite(P_LORA_TX_LED, LED_STATE_ON);
|
|
}
|
|
|
|
void T1Board::onAfterTransmit() {
|
|
digitalWrite(P_LORA_TX_LED, !LED_STATE_ON);
|
|
}
|
|
|
|
uint16_t T1Board::getBattMilliVolts() {
|
|
analogReadResolution(12);
|
|
analogReference(VBAT_AR_INTERNAL);
|
|
pinMode(PIN_VBAT_READ, INPUT);
|
|
pinMode(PIN_BAT_CTL, OUTPUT);
|
|
digitalWrite(PIN_BAT_CTL, ADC_CTRL_ENABLED);
|
|
|
|
delay(10);
|
|
int adcvalue = analogRead(PIN_VBAT_READ);
|
|
digitalWrite(PIN_BAT_CTL, !ADC_CTRL_ENABLED);
|
|
|
|
return (uint16_t)((float)adcvalue * MV_LSB * ADC_MULTIPLIER);
|
|
}
|
|
|
|
void T1Board::variant_shutdown() {
|
|
nrf_gpio_cfg_default(PIN_TFT_CS);
|
|
nrf_gpio_cfg_default(PIN_TFT_DC);
|
|
nrf_gpio_cfg_default(PIN_TFT_SDA);
|
|
nrf_gpio_cfg_default(PIN_TFT_SCL);
|
|
nrf_gpio_cfg_default(PIN_TFT_RST);
|
|
nrf_gpio_cfg_default(PIN_TFT_LEDA_CTL);
|
|
nrf_gpio_cfg_default(PIN_TFT_VDD_CTL);
|
|
|
|
nrf_gpio_cfg_default(PIN_WIRE_SDA);
|
|
nrf_gpio_cfg_default(PIN_WIRE_SCL);
|
|
|
|
nrf_gpio_cfg_default(LORA_CS);
|
|
nrf_gpio_cfg_default(SX126X_DIO1);
|
|
nrf_gpio_cfg_default(SX126X_BUSY);
|
|
nrf_gpio_cfg_default(SX126X_RESET);
|
|
nrf_gpio_cfg_default(PIN_SPI_MISO);
|
|
nrf_gpio_cfg_default(PIN_SPI_MOSI);
|
|
nrf_gpio_cfg_default(PIN_SPI_SCK);
|
|
|
|
nrf_gpio_cfg_default(PIN_SPI1_MOSI);
|
|
nrf_gpio_cfg_default(PIN_SPI1_SCK);
|
|
|
|
nrf_gpio_cfg_default(PIN_GPS_RESET);
|
|
nrf_gpio_cfg_default(PIN_GPS_EN);
|
|
nrf_gpio_cfg_default(PIN_GPS_PPS);
|
|
nrf_gpio_cfg_default(PIN_GPS_RX);
|
|
nrf_gpio_cfg_default(PIN_GPS_TX);
|
|
|
|
nrf_gpio_cfg_default(PIN_BUZZER_VOLTAGE_MULTIPLIER_1);
|
|
nrf_gpio_cfg_default(PIN_BUZZER_VOLTAGE_MULTIPLIER_2);
|
|
|
|
pinMode(PIN_BUZZER, OUTPUT);
|
|
digitalWrite(PIN_BUZZER, LOW);
|
|
|
|
pinMode(PIN_SENSOR_EN, OUTPUT);
|
|
digitalWrite(PIN_SENSOR_EN, !PIN_SENSOR_EN_ACTIVE);
|
|
|
|
pinMode(PIN_LED1, OUTPUT);
|
|
digitalWrite(PIN_LED1, !LED_STATE_ON);
|
|
|
|
pinMode(PIN_BAT_CTL, OUTPUT);
|
|
digitalWrite(PIN_BAT_CTL, !ADC_CTRL_ENABLED);
|
|
}
|
|
|
|
void T1Board::powerOff() {
|
|
variant_shutdown();
|
|
sd_power_system_off();
|
|
}
|
|
|
|
const char* T1Board::getManufacturerName() const {
|
|
return "Heltec T1";
|
|
}
|