mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-03-30 14:55:46 +00:00
96 lines
2.9 KiB
C++
96 lines
2.9 KiB
C++
#include "ThinkNodeM1Board.h"
|
|
#include <Arduino.h>
|
|
|
|
#ifdef THINKNODE_M1
|
|
|
|
#include <Wire.h>
|
|
#include <bluefruit.h>
|
|
|
|
static BLEDfu bledfu;
|
|
|
|
static void connect_callback(uint16_t conn_handle) {
|
|
(void)conn_handle;
|
|
MESH_DEBUG_PRINTLN("BLE client connected");
|
|
}
|
|
|
|
static void disconnect_callback(uint16_t conn_handle, uint8_t reason) {
|
|
(void)conn_handle;
|
|
(void)reason;
|
|
|
|
MESH_DEBUG_PRINTLN("BLE client disconnected");
|
|
}
|
|
|
|
void ThinkNodeM1Board::begin() {
|
|
// for future use, sub-classes SHOULD call this from their begin()
|
|
startup_reason = BD_STARTUP_NORMAL;
|
|
|
|
Wire.begin();
|
|
|
|
#ifdef P_LORA_TX_LED
|
|
pinMode(P_LORA_TX_LED, OUTPUT);
|
|
digitalWrite(P_LORA_TX_LED, LOW);
|
|
#endif
|
|
|
|
pinMode(SX126X_POWER_EN, OUTPUT);
|
|
digitalWrite(SX126X_POWER_EN, HIGH);
|
|
delay(10); // give sx1262 some time to power up
|
|
}
|
|
|
|
uint16_t ThinkNodeM1Board::getBattMilliVolts() {
|
|
int adcvalue = 0;
|
|
|
|
analogReference(AR_INTERNAL_3_0);
|
|
analogReadResolution(12);
|
|
delay(10);
|
|
|
|
// ADC range is 0..3000mV and resolution is 12-bit (0..4095)
|
|
adcvalue = analogRead(PIN_VBAT_READ);
|
|
// Convert the raw value to compensated mv, taking the resistor-
|
|
// divider into account (providing the actual LIPO voltage)
|
|
return (uint16_t)((float)adcvalue * REAL_VBAT_MV_PER_LSB);
|
|
}
|
|
|
|
bool ThinkNodeM1Board::startOTAUpdate(const char *id, char reply[]) {
|
|
// Config the peripheral connection with maximum bandwidth
|
|
// more SRAM required by SoftDevice
|
|
// Note: All config***() function must be called before begin()
|
|
Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
|
|
Bluefruit.configPrphConn(92, BLE_GAP_EVENT_LENGTH_MIN, 16, 16);
|
|
|
|
Bluefruit.begin(1, 0);
|
|
// Set max power. Accepted values are: -40, -30, -20, -16, -12, -8, -4, 0, 4
|
|
Bluefruit.setTxPower(4);
|
|
// Set the BLE device name
|
|
Bluefruit.setName("THINKNODE_M1_OTA");
|
|
|
|
Bluefruit.Periph.setConnectCallback(connect_callback);
|
|
Bluefruit.Periph.setDisconnectCallback(disconnect_callback);
|
|
|
|
// To be consistent OTA DFU should be added first if it exists
|
|
bledfu.begin();
|
|
|
|
// Set up and start advertising
|
|
// Advertising packet
|
|
Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
|
|
Bluefruit.Advertising.addTxPower();
|
|
Bluefruit.Advertising.addName();
|
|
|
|
/* Start Advertising
|
|
- Enable auto advertising if disconnected
|
|
- Interval: fast mode = 20 ms, slow mode = 152.5 ms
|
|
- Timeout for fast mode is 30 seconds
|
|
- Start(timeout) with timeout = 0 will advertise forever (until connected)
|
|
|
|
For recommended advertising interval
|
|
https://developer.apple.com/library/content/qa/qa1931/_index.html
|
|
*/
|
|
Bluefruit.Advertising.restartOnDisconnect(true);
|
|
Bluefruit.Advertising.setInterval(32, 244); // in unit of 0.625 ms
|
|
Bluefruit.Advertising.setFastTimeout(30); // number of seconds in fast mode
|
|
Bluefruit.Advertising.start(0); // 0 = Don't stop advertising after n seconds
|
|
|
|
strcpy(reply, "OK - started");
|
|
return true;
|
|
}
|
|
#endif
|