A room server is an endpoint, not a repeater. Strip the repeater
machinery the role inherited from the RepeaterMesh clone:
- allowPacketForward() returns false unconditionally — never relays
transit traffic. (Upstream's simple_room_server gates this on
disable_fwd; hard-off here since the role should never repeat.)
- neighbour tracking: NeighbourInfo/neighbours[], putNeighbour,
onAdvertRecv, removeNeighbor; formatNeighborsReply -> "not supported"
- node discovery: onControlDataRecv, sendNodeDiscoverReq, the
discover.neighbors CLI, discover rate-limiter + pending state
- loop detection: isLooped + max_loop_* tables + loop_detect pref
- dead code: RepeaterStats struct, GET_NEIGHBOURS handler, simple_sort
-344 lines net. Builds clean (FLASH 30.7% / RAM 32.2%); login, post,
push/sync, read-only guest and admin remote-management all
hardware-verified on the GAT562 kit.
The room server's onAnonDataRecv handles login inline (the room login
protocol carries a sync_since cursor the repeater's doesn't), so the
cloned repeater helpers handleLoginReq + handleAnonRegionsReq /
handleAnonOwnerReq / handleAnonClockReq — and the anon_limiter they used
— were dead after the port. Remove them (~160 lines). No behavior change.
The inherited neighbor-tracking / node-discovery machinery is also unused
on a room server; left in place for now (can be trimmed in a follow-up).
StrHelper::strncpy null-terminates but does NOT zero-pad the 16-byte
password buffer, so setting a shorter password over a longer previous
value (e.g. one inherited from a prior repeater config) leaves trailing
garbage. onAnonDataRecv's constant-time compare runs over the full
buffer width, so a correct password stopped matching — admin/guest
logins were silently rejected, or downgraded to a read-only guest when
allow_read_only was on (the login looked identical to read-only).
Fix: copy both stored passwords into zeroed buffers (up to strnlen)
before the constant-time compare, so the comparison reflects the actual
string while staying constant-time over the full width.
Hardware-verified on the kit: admin login with the correct password now
grants ADMIN (post + remote management), confirmed server-side via
get acl (perms 03).
Note: the repeater's handleLoginReq shares this latent issue.
Two hardware-found fixes after on-air testing on the GAT562 kit:
- Add a 500ms push timer in main_room_server.cpp so the post-sync
engine advances at its intended cadence. ZephCore is event-driven
(no Arduino superloop), so without this the engine only ran on the
5s housekeeping tick — posts dripped out every ~5s and transmits
bunched up, causing timeouts/resends.
- Lower the post-sync hold from upstream's conservative defaults
(POST_SYNC_DELAY 6s -> 2s, PUSH_NOTIFY 2000ms -> 1000ms). These are
server-side timing only (no wire-format change), and take measured
delivery from ~6-7s down to ~2s.
Verified on hardware (910.525/62.5/SF7/CR8, two clients): normal-pace
messages deliver in ~2s with clean ACKs. Rapid-fire bursts can still
drop out-of-order messages via the per-client timestamp replay check
(unchanged from upstream) — left as-is to stay upstream-compatible.
Add the MeshCore Room Server role to ZephCore — a store-and-forward
shared message room. Clients log in with an admin or guest password
and post messages; the server pushes each new post to all other
logged-in clients (round-robin, per-client sync cursor, ACK + retry,
3-strike eviction).
Ported from upstream MeshCore's simple_room_server, structured as a
near-clone of RepeaterMesh so it reuses the proven ACL, region
filtering, CLI, adverts and telemetry; the post buffer + push engine
are the only net-new pieces:
- RoomServerMesh: PostInfo ring (MAX_UNSYNCED_POSTS=32), addPost,
pushPostToClient, getUnsyncedCount, processAck, onAckRecv, the
loop() push driver; room login (onAnonDataRecv parses the
sync_since cursor); posts/admin-CLI/keep-alive (onPeerDataRecv);
ADV_TYPE_ROOM advert; ServerStats wire layout; disable_fwd=1.
- main_room_server.cpp: event-loop entry (USB serial CLI, no BLE).
- Kconfig: ZEPHCORE_ROLE_ROOM_SERVER + ZEPHCORE_MAX_UNSYNCED_POSTS.
- CMakeLists role gating; boards/common/room_server.conf.
Post frame, SHA-256 ACK and login-reply layouts match upstream for
MeshCore app compatibility. Builds for gat562_30s
(FLASH 30.95% / RAM 32.46%). Not yet hardware-tested.
liquidraver