server_main_common.cpp and main_observer.cpp both configured led0 as
a plain GPIO output at boot, unconditionally. On ESP32 that calls
esp_rom_gpio_matrix_out() under the hood, which routes the pin's
output to the GPIO signal and takes it away from whatever peripheral
had it before, including the LEDC channel a heartbeat-pwm-led or
lora-tx-pwm-led alias had already claimed during the PWM driver's own
init. The PWM write then succeeds (no error, no warning) but never
reaches the pin: confirmed on V4.3 hardware, where the same pin lights
up fine over plain GPIO, and over PWM in a different (non-Zephyr)
firmware, but stays dark over Zephyr's PWM once this GPIO configure
has run.
Companion builds never hit this (they don't use server_main_common.cpp)
and nRF52 isn't affected (no shared GPIO matrix), which is why T096
tested fine while V4.3 didn't.
Fix is alias-based, not a board list, so any future board with either
PWM alias is covered without extra wiring.
Also: CLI_HAS_RADIO_LED only checked the plain lora-tx-led alias, so
"set leds.radio" replied "(no radio LED on this board)" on boards
whose radio LED exists only via lora-tx-pwm-led (V4.3). Check both.
Documents the two PWM aliases in the board porting guide, and
leds.brightness plus the corrected LED topology counts in
docs/CLI_commands.md.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
- gps: servers honour gps_enabled at boot (was lost on reboot; zc.gps_set
upgrades older prefs to on once); sleep lock only while acquiring;
gps off works on boards without a power line (UART sleep); UI toggles
and fixes handled on the main thread; configure only after a good init;
observer parks its GPS; one interval clamp (clampGpsInterval); one
nav-mode knob (room servers on Air530Z now stationary); GNSS UARTE from DT
- gps: split into ZephyrGPSManager / gps_power / gps_module_cfg
(+gps_internal.h); dead driver branches, gps_get_diag, sats_* removed
- clock: ZephyrRTCClock writes the hardware RTC itself (clkreboot now
resets it); MESH_EVENT_RTC_SAVE gone
- power: one power-off path (zephcore_power_off, ZephyrBoard::powerOff),
poweroff/shutdown CLI, get pwrmgt.*, crash record kept across reboot,
battery reading cached 10 s, fuel gauge on the current API
- telemetry: upstream SensorManager + CayenneLPP (rounded to nearest),
one builder for all roles; per-sensor channels, MCU temp always,
guest gating and inverse mask on servers; sensor list/get/set work;
BME280/BMP280 also probed at 0x77
- CLI: gps in upstream's form, get gps detail, gps sync
Server roles (slice 7)
- CommonCLI split into upstream's shape; region CLI moved into CommonCLI;
ClientACL, RegionMap, TransportKeyStore and both server meshes in
upstream shape over an Arduino compat shim (helpers/compat: Arduino.h,
Stream/Print, Serial, SHA256, FILESYSTEM/File over Zephyr fs)
- room server processAck port; `get acl` prints as upstream
- room: default name Room-XXXX, display/input rotation, live radio UI refresh
Event loops (slice 7b)
- repeater and room server share server_main_common with a ServerRole
descriptor; shared event bits in src/mesh_events.h
- room server deadline-driven (idle wakes 2.2/s -> 0.08/s); companion
loop() runs on housekeeping (closes the lazy contact-flush gap)
- `get loop.wakes` in debug builds (CONFIG_ZEPHCORE_LOOP_WAKE_STATS)
Companion transports and WiFi (slice 8)
- upstream MultiSerialInterface: BLE, USB/UART and TCP are each a
BaseSerialInterface, every connected transport gets every frame;
CompanionSerial holds a lossless reply; shared frame_txq for BLE/TCP
- SerialCompanionTransport and LinuxTCPTransport replaced by
TcpCompanionTransport; ZephyrBLE split (gatt layout, DFU)
- WiFi companion (upstream wifi.ssid/pwd/enabled CLI, TCP port 5000) on
boards declaring `capabilities: wifi` in zephcore.yml: the PSRAM
ESP32-S3 boards, plus Heltec V3 (140 contacts), Wireless Tracker (130)
and both C6 boards (280); ESP32-S3 without PSRAM gets bounded WiFi
buffers and a measured 72 KB heap; PSRAM boards' internal heap 72 KB
- TCP queues: own depth (ZEPHCORE_TCP_QUEUE_SIZE=8), RX waits instead
of dropping
- RAM: companion ClientACL dropped; main/BT-TX/TCP stacks sized from
measured peaks (-7 KB nRF companions, -9 KB ESP32 companions)
- ESP32 WiFi stopped working under ~200 frames/s unicast. Fixed by:
patches/zephyr/0017 never block the WiFi task in the RX callback;
patches/zephyr/0018 lock shared_multi_heap (heap corruption with the
WiFi heap in PSRAM); patches/modules/hal_espressif/0001 backport of
hal_espressif af97fb02df (PSRAM realloc)
Storage and prefs (slice 9)
- prefs are now prefs.json through upstream's ConfigSerializer (ported
verbatim), with upstream's key names for shared fields and ZephCore's
own under "zc"; on first boot the binary new_prefs / repeater prefs is
migrated and kept, so a downgrade still boots with the old settings
- helpers/PrefsCodec: both legacy binary layouts (companion 272 B,
server 311 B) as Zephyr-free codecs; sanitizeNodePrefs is the only
validator
- fix: server prefs could be replaced by a truncated file when a write
failed; identity, prefs and channel writes go through one checked
atomic replace (ZephyrFsUtil)
- fix: a corrupt cad_auto byte turned adaptive CAD off instead of the
default on
- fix: a deliberate 300 s GPS duty on a repeater was rewritten to 48 h
on every boot (that migration now runs on legacy files only)
- one identity loader for all roles (IdentityFile); an unusable key
file is always parked as .bad before regenerating
- server store no longer stamps repeater defaults on room server and
observer; companion first-boot volume policy moved into the store
(adoptVolume)
- ZephyrDataStore 1435 -> ~850 lines
- LoRaRadioBase -> LoRaRadio (final); SX126x/SX127x/LR1110/LR2021Radio
replaced by const LoRaRadioOps tables (radio_ops_<family>.cpp), one
linked per build; mains construct the radio in one line
- lr20xx: vendored Semtech SDK + HAL moved beside the driver (no app-tree
sources), DIO1 handler split (CCN 52 -> 10), zc_lora_timing.h adopted,
dead exports removed, header rewritten, comment diet (image-identical)
- semtech,lr2021 uses the lr1110 property names (irq-gpios, tcxo-voltage,
rfsw-*), compiled config byte-identical
- correct the stale "LR2021 is not CAD-probed" claim
- CadController (stats, window, re-anchor, visits, staircase, safety,
starvation relax) and NoiseFloorEstimator split out of LoRaRadioBase
behind a 4-call CadHw interface; Zephyr-free, host unit tests added
- prefs mandatory: setPrefs() before begin(), LoRaConfig fallbacks and the
companion/observer placeholder prefs removed; LoRaConfig is the one
defaults source (invalid-prefs fallback now uses the board TX default)
- TX-wait thread stack owned by the base; reconfigureWithParams removed
- driver extension headers on the public include path
(zephyr/drivers/lora/*.h); patch 0003 include updated
- comment diet (image-identical); rationale moved to devdocs LLD 03
- Mesh, Dispatcher, Packet, packet pool and the core headers rebuilt from
Arduino MeshCore's text; ZephCore changes re-applied, each fenced
`// ZEPHCORE:` (diff vs upstream: 4540 -> 1147 lines)
- upstream header layout; MainBoard gains handleCommand/loop and the other
upstream members; RNG::nextInt back in Utils.cpp
- packet logging moved to the roles' log hooks (helpers/PacketLog.h)
- zero-hop direct ACKs deduplicated and length-checked as upstream
- RadioIncludes.h -> src/, LoRaConfig.h -> helpers/
- .editorconfig: shared files keep upstream formatting
Verified: 10 role builds, per-function disassembly review, bench DM/ACK
regression (T1000-E, Wio L1, XIAO S3 on 1.17.4) incl. via live repeater.
- track real RTC sync source on the joystick Time screen
- gate joystick-only UI helpers behind stub headers so non-joystick builds skip the extra code without #ifdef at every call site.
