ESP32 light sleep (devdocs/lld/13-power-management.md)
Light sleep on the S3 repeaters never worked as designed, for two
independent reasons:
- No S3 repeater ever slept. Every one carries WiFi OTA, the WiFi
driver starts WiFi at boot (NULL mode), and a started WiFi library
holds its modem PM lock. Measured on the XIAO: zero sleep entries
with WiFi compiled in. helpers/pm_esp32_wake.c now stops WiFi at
boot on PM builds; `start ota` and a station connect start it again
(verified: AP up, sleep blocked for the session, sleeping after
`stop ota`).
- DIO1 was not a wake source. GPIO_INT_WAKEUP means EXT1 in Zephyr's
ESP32 driver: RTC pads only, one trigger polarity for all pins on
the S3, and pads left on the RTC mux after every sleep. Since 1.17.1
pm_esp32.overlay also armed the active-low user button; gpio-keys
configures first, so the driver refused the active-high DIO1.
The new helper arms the radio IRQ line and the user button (sw0) as
per-pin level GPIO wakes (ESP-IDF gpio_wakeup_enable, any pad) for the
length of each sleep, masks their CPU interrupt while in level mode,
and re-raises the interrupt a sleep swallowed through status_w1ts, so
the radio's dio1_isr and gpio-keys run as usual. EXT1 is no longer
used: patch 0003 configures DIO1 as a plain input again and drops the
d7cc4cb pad-restore notifier (preamble section rewritten). Non-RTC
DIO1 boards (XIAO GPIO39, Station G2 GPIO48) can now light-sleep.
Each light sleep is also bounded by the next esp_timer alarm
(pm_policy_next_custom_ticks, CONFIG_PM_CUSTOM_TICKS_HOOK), as ESP-IDF
does; the BLE controller's modem-sleep wake timer lives there.
Light sleep isolates every pad that is not held, RTC or digital, while
the radio keeps receiving. Holds (ESP32_GPIO_SLEEP_HOLD_EN, inert
without PM) now live in each board's own files: NSS and RESET on all
PM-capable boards, VFEM_Ctrl (GPIO7) and Vext on V4/V4.3/V4 R8/WTv2,
CPS on V4, RXEN on the XIAO. The shared overlay keeps only &rtc_timer
and the GPIO wake source; the wrong RTC_PERIPH explanations are gone.
Also:
- `powersaving` (upstream's command and replies) gates light sleep;
light-sleep builds default to on, and a stored 0 without the new
pwr_sav_set marker (the field did nothing before) becomes on once.
`powersaving off` persists and keeps the node (and its USB) awake.
- `get pm`: asleep %, sleeps, wake causes, per-pin wake counts.
- The console window reopens on every user-button press.
- XIAO ESP32-S3: GPIO21 is both the kit's user button and the board's
led0; the heartbeat drove it low and every sleep woke as a button
press. led0 is deleted, the button gets a pull-up.
- Station G2: button active-low with pull-up, as upstream reads it
(was active-high). Untested on hardware.
Verified on the XIAO ESP32-S3 as a light-sleep repeater on the live
mesh (repeat off, 2 dBm) against a T1000-E on the same channel: awake
20 min, ratio of floods heard 0.95; asleep 30.5 min (96.6 % of
uptime), 119 vs 119, ratio 1.00. TX: sent == flood + direct. Heltec
boards: build-only (no unit on the bench).
Companion light sleep stays off by default; the esp_timer bound makes
it possible. Spike on the XIAO (pm_esp32.conf by hand, BLE only): a
held connection survives, 35 min with a poll every minute and no
miss, the SoC asleep ~91 % between connection events, LoRa RX 130 vs
~130 on the T1000-E. Pairing while asleep fails; USB CDC and UI still
need locks before companions can ship with it.
Flash wear (storage)
The companion marked contacts dirty on is_new, but upstream's is_new
means "not in contacts[]": auto-add declined the node (type filter,
hop limit, full table). Every advert from such a node forced a 5 s
full rewrite of an unchanged contacts3, while a contact that really
was just added only got the liveness deadline. onAdvertRecv now
snapshots the stored record first. is_new never dirties. An addition
or a changed name, type or position flushes in 5 s, and a plain
re-advert waits the liveness deadline, now 1 h instead of 10 min.
A new weak hook, zephcore_persist_before_off(), flushes the deferred
writes before every clean reboot and power-off. It is called from
zephcore_power_off(), the ZephyrBoard reboot, bootloader and BLE-OTA
paths, the UI save-and-restart, the joystick restart and wifi_ota.
Off the main thread it posts MESH_EVENT_PERSIST and waits up to 5 s.
Before this, only CMD_REBOOT flushed.
The repeater saved its ACL on every admin login. It now saves only
when the role or secret changed; the secret is the ECDH of two fixed
keys, so re-logins store nothing new. The room server likewise skips
the lazy write unless the role, sync_since or secret changed.
zephcore_prefs_json_save() compares the serialised JSON with the file
and skips an identical rewrite. Not tested on hardware.
Builds and tests: role_builds.sh 10/10; the ESP32 PM set on the
combined tree (five Heltec repeaters, V4 R8, Station G2, XIAO repeater
and companion) 9/9, repeaters at 69-71 % dram0; board_manifest check
clean; host tests quick 114/114. heltec_companion dram0 at 99.80 %
(776 B left, +88 B for both changes together).
- gps: servers honour gps_enabled at boot (was lost on reboot; zc.gps_set
upgrades older prefs to on once); sleep lock only while acquiring;
gps off works on boards without a power line (UART sleep); UI toggles
and fixes handled on the main thread; configure only after a good init;
observer parks its GPS; one interval clamp (clampGpsInterval); one
nav-mode knob (room servers on Air530Z now stationary); GNSS UARTE from DT
- gps: split into ZephyrGPSManager / gps_power / gps_module_cfg
(+gps_internal.h); dead driver branches, gps_get_diag, sats_* removed
- clock: ZephyrRTCClock writes the hardware RTC itself (clkreboot now
resets it); MESH_EVENT_RTC_SAVE gone
- power: one power-off path (zephcore_power_off, ZephyrBoard::powerOff),
poweroff/shutdown CLI, get pwrmgt.*, crash record kept across reboot,
battery reading cached 10 s, fuel gauge on the current API
- telemetry: upstream SensorManager + CayenneLPP (rounded to nearest),
one builder for all roles; per-sensor channels, MCU temp always,
guest gating and inverse mask on servers; sensor list/get/set work;
BME280/BMP280 also probed at 0x77
- CLI: gps in upstream's form, get gps detail, gps sync
Add a board-aware battery SOC system replacing the two independent
linear approximations that existed in the UI helpers.
New helpers/battery_curve.{h,c}: a 21-point (5% step) OCV lookup table
with integer linear interpolation. The default generic LiPo curve is a
weak symbol — any board can override it by dropping a battery_curve.c
into its board directory. CMakeLists.txt selects the board-specific file
when present, falling back to the generic.
Board.h gains getBattPercent() (default 0); ZephyrBoard implements it
via battery_curve_lookup().
Board-specific curves added for boards with measured cell data:
t1000_e, rak_wismesh_tag, thinknode_m6, sensecap_solar, wio_tracker_l1.
ADC multiplier corrections applied across all nRF52840 boards:
- Boards using a correctly-derived 3600×ratio formula get +0.5% to
compensate for nRF SAADC gain error (7200→7236, 6300→6332, etc.)
- rak_wismesh_tag, rak3401_1watt, gat562_30s had multipliers copied
from Arduino's 3.0V AREF formula; corrected to 3600×1.73×1.005=6259
- xiao_nrf52840 (10911) left unchanged — empirically calibrated value
above the theoretical, assumed already correct for that hardware
get adc.multiplier now reports current mV reading and the board's
curve 100% target, making field calibration self-guiding.
liquidraver