mirror of
https://github.com/liquidraver/ZephCore.git
synced 2026-10-15 06:19:55 +00:00
142 lines
6.9 KiB
Plaintext
142 lines
6.9 KiB
Plaintext
# ============================================================================
|
|
# ZephCore — board.conf template
|
|
# ============================================================================
|
|
#
|
|
# Only for settings that cannot be derived from devicetree. Most hardware
|
|
# features switch themselves on:
|
|
#
|
|
# Feature Enabled by
|
|
# ─────────────── ──────────────────────────────────────────────────
|
|
# Display DT chosen: zephyr,display
|
|
# Buzzer + PWM DT nodelabel: buzzer (child of a "pwm-leds" node)
|
|
# QSPI flash DT node: compatible "nordic,qspi-nor"
|
|
# GPS DT nodelabel: gnss (a GNSS driver on a UART)
|
|
# I2C sensors DT: boards/common/sensors-i2c.dtsi, probed at runtime
|
|
# Hardware RTC DT: boards/common/rtc-i2c.dtsi, probed at boot
|
|
# ESP32 PSRAM DT: psram0 size > 0 (zephcore/Kconfig.psram)
|
|
#
|
|
# Config chain (later files override earlier ones):
|
|
# prj.conf → zephcore_common.conf → <platform>_common.conf
|
|
# → esp32c3s3_common.conf (ESP32-S3/C3 only) → THIS FILE
|
|
# → auto-included feature confs → your -DEXTRA_CONF_FILE
|
|
#
|
|
# The platform conf is chosen by the directory this board lives in
|
|
# (boards/nrf52840/, nrf54l/, esp32/, mg24/, stm32wl/). There is nothing to
|
|
# register in CMakeLists.txt.
|
|
#
|
|
# DO NOT duplicate settings from the common confs.
|
|
#
|
|
# ============================================================================
|
|
|
|
# ========== REQUIRED: Board Identity ==========
|
|
# Name reported to the phone app and by the `board` CLI command. 39 characters
|
|
# at most (static_assert in app/CompanionMesh.cpp). Match the Arduino MeshCore
|
|
# variant's name where one exists.
|
|
CONFIG_ZEPHCORE_BOARD_NAME="My Board"
|
|
|
|
# BLE Device Information Service model name (shown in phone settings)
|
|
CONFIG_BT_DIS_MODEL_NUMBER_STR="My Board v1"
|
|
|
|
# ========== REQUIRED (nRF52 only): SoftDevice Firmware ID ==========
|
|
# Written into the DFU .zip (adafruit-nrfutil --sd-req). It MUST match the
|
|
# SoftDevice the board's Adafruit bootloader was flashed with, and the
|
|
# partition include in the DTS must be the matching one:
|
|
#
|
|
# Arduino variant linker script FWID DTS include
|
|
# nrf52840_s140_v6*.ld (app@0x26000) 0x00B6 nrf52_partitions_sdv6.dtsi
|
|
# nrf52840_s140_v7*.ld (app@0x27000) 0x0123 nrf52_partitions_sdv7.dtsi
|
|
#
|
|
# The wrong pair puts the app at the wrong address: bootloop, no USB, no logs.
|
|
#
|
|
# CONFIG_ZEPHCORE_SD_FWID=0x00B6 # s140 v6.1.1 (RAK4631, ThinkNode M1/M3/M6, Heltec T114)
|
|
# CONFIG_ZEPHCORE_SD_FWID=0x0123 # s140 v7.3.0 (XIAO nRF52840, Wio Tracker L1, T1000-E)
|
|
|
|
# ========== OPTIONAL: Radio Type ==========
|
|
# Default: ZEPHCORE_RADIO_NATIVE (Zephyr's SX126x driver: SX1261/62/68, LLCC68,
|
|
# STM32WL). Nothing to set for those. Otherwise pick the one that matches the
|
|
# lora node's compatible:
|
|
# CONFIG_ZEPHCORE_RADIO_LR1110=y # semtech,lr1110 (LR1110/LR1120/LR1121)
|
|
# CONFIG_ZEPHCORE_RADIO_LR2021=y # semtech,lr2021
|
|
#
|
|
# SX127x goes through the loramac-node backend and needs the whole group
|
|
# (source-only path, see boards/esp32/ttgo_lora32/):
|
|
# CONFIG_LORA_MODULE_BACKEND_NATIVE=n
|
|
# CONFIG_LORA_MODULE_BACKEND_LORAMAC_NODE=y
|
|
# CONFIG_ZEPHCORE_RADIO_SX127X=y
|
|
# CONFIG_ZEPHCORE_DEFAULT_TX_POWER_DBM=17
|
|
|
|
# ========== OPTIONAL: TX Power (boards with an external PA / FEM) ==========
|
|
# Both default to 22 dBm, the SX1262 maximum. With a PA after the chip, the
|
|
# chip must be held below the PA's maximum input:
|
|
# CONFIG_ZEPHCORE_DEFAULT_TX_POWER_DBM=14
|
|
# CONFIG_ZEPHCORE_MAX_TX_POWER_DBM=19 # hard cap, enforced by the radio adapter
|
|
|
|
# ========== OPTIONAL: Companion table sizes (RAM-bound boards) ==========
|
|
# Defaults: 350 contacts, 40 channels, 256 queued offline messages. The
|
|
# companion is limited by RAM, not flash, so the boards that override these
|
|
# lower them. Values in the tree today:
|
|
# nRF52840 350 (default)
|
|
# nRF54L15 450 (nRF54LM20A: 510)
|
|
# ESP32-C3 300
|
|
# ESP32-C6 280
|
|
# ESP32-S3 without PSRAM 130-140 (Heltec V3, Wireless Tracker)
|
|
# Classic ESP32 50-140, with MAX_CHANNELS / OFFLINE_QUEUE_SIZE trimmed too
|
|
# STM32WL (64 KB SRAM) 12
|
|
# Raise it only after reading the RAM figure in the build's memory report.
|
|
# CONFIG_ZEPHCORE_MAX_CONTACTS=300
|
|
# CONFIG_ZEPHCORE_MAX_CHANNELS=8
|
|
# CONFIG_ZEPHCORE_OFFLINE_QUEUE_SIZE=128
|
|
|
|
# ========== OPTIONAL: Display heap (nRF52 / nRF54L with a large panel) ==========
|
|
# The CFB framebuffer is k_malloc'd at boot. The 2048-byte default in
|
|
# zephcore_common.conf fits a 128x64 OLED (1024 bytes). A larger panel fails
|
|
# with -ENOMEM and stays blank, with no other symptom.
|
|
#
|
|
# Panel Resolution Framebuffer Heap in the tree
|
|
# SSD1306/SH1106 128x64 1024 bytes 2048 (default)
|
|
# ST7735 mono TFT 160x80 1600 bytes 4096
|
|
# SSD1681 e-paper 200x200 5000 bytes 6144
|
|
#
|
|
# ESP32 and MG24 already have a heap of tens of KB and need no override.
|
|
# CONFIG_HEAP_MEM_POOL_SIZE=6144
|
|
|
|
# ========== OPTIONAL: UI ==========
|
|
# Boards whose long press emits KEY_ENTER: two confirms do not fit in the
|
|
# default 500 ms window.
|
|
# CONFIG_ZEPHCORE_UI_CONFIRM_WINDOW_MS=3000
|
|
# Larger built-in font for high-resolution panels (e-paper).
|
|
# CONFIG_ZEPHCORE_DISPLAY_LARGE_FONT=y
|
|
|
|
# ========== OPTIONAL: ESP32 ==========
|
|
# esp32_common.conf assumes 4 MB flash. Set the real size; sysbuild copies it
|
|
# to the MCUboot image (sysbuild/CMakeLists.txt). A mismatch hangs MCUboot at
|
|
# "spi_flash: detected chip:".
|
|
# CONFIG_ESPTOOLPY_FLASHSIZE_8MB=y
|
|
# CONFIG_ESPTOOLPY_FLASHSIZE_16MB=y
|
|
#
|
|
# PSRAM is enabled from devicetree. Only the mode of an 8 MB octal part
|
|
# (ESP32-S3R8) has to be stated; 2 MB quad (R2) is the upstream default.
|
|
# CONFIG_SPIRAM_MODE_OCT=y
|
|
#
|
|
# Classic ESP32 PICO-D4 bootloops when the bootloader enables QIO flash mode.
|
|
# CONFIG_ESPTOOLPY_FLASHMODE_DIO=y
|
|
# CONFIG_ESPTOOLPY_FLASHMODE_QIO=n
|
|
#
|
|
# Boards with an I2C fuel gauge / PMU that reports state of charge (AXP2101).
|
|
# CONFIG_FUEL_GAUGE=y
|
|
|
|
# ========== DO NOT SET HERE ==========
|
|
# CONFIG_ZEPHCORE_UI_DISPLAY / _UI_BUZZER / CONFIG_PWM / CONFIG_DISPLAY
|
|
# follow devicetree (exception: a board whose panel is an optional
|
|
# plug-in forces UI_DISPLAY=y, see boards/nrf52840/rak4631/)
|
|
# CONFIG_SPI, CONFIG_LORA selected by the radio type
|
|
# CONFIG_NORDIC_QSPI_NOR follows the nordic,qspi-nor node
|
|
# CONFIG_ESP_SPIRAM / _SIZE follow the psram0 node
|
|
# CONFIG_ZEPHCORE_LORA_RX_DUTY_CYCLE
|
|
# boot default is off for every role; users switch it with `set rxduty`
|
|
# CONFIG_ZEPHCORE_ROLE_*, CONFIG_LOG*, CONFIG_BT=n
|
|
# role and debug policy come from boards/common/*.conf, never from a board
|
|
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_*
|
|
# ignored since the Zephyr main pin; the 32.768 kHz source is devicetree
|
|
# (&lfclk { k32src = "rc"; }, see board.overlay and docs/adr/0005)
|