ZephCore/docs/supported_boards.md

Supported Boards

Board strings for use with west build -b <board> zephcore.

nRF52840

rak4631
rak3401_1watt
wio_tracker_l1
t1000_e
meshtracker_x1
thinknode_m1
thinknode_m3
thinknode_m6
rak_wismesh_tag
ikoka_nano_30dbm
sensecap_solar
xiao_nrf52840
lilygo_techo
promicro_sx1262
promicro_lr2021
heltec_t114
heltec_t096
heltec_t1
gat562_30s
muziworks_r1neo
lilygo_timpulse_plus

RAK WisMesh Pocket (WisBlock pocket): use -b rak4631 — same board string and firmware as RAK4631.

Heltec T114 screenless build: append boards/nrf52840/heltec_t114/no_display.conf to EXTRA_CONF_FILE for units without the TFT module.

SenseCAP MeshTracker X1 (meshtracker_x1): nRF52840 + LR2021, AG3335M dual-band L1+L5 GNSS, SPA06 barometer, DRV2605L vibration, YSN8900 RTC, 8 MB QSPI flash (/ext), RGB LED, buzzer. Untested on hardware — first ZephCore board to use a real LR2021. The RTC is treated as an RX8900 second-source; boot-time discovery validates that before trusting it.

Heltec Mesh Node T096 (heltec_t096): nRF52840 with SX1262 + KCT8103L PA/FEM, UC6580 GNSS, and ST7735S 160x80 TFT companion display. The external SPI flash footprint is documented in the board notes but left disabled until the device parameters are confirmed.

Heltec Mesh Node T1 (heltec_t1): nRF52840 + SX1262 handheld tracker card with UC6580 L1+L5 GNSS, ST7735S 160x80 TFT, PAM8904-driven piezo buzzer, two buttons and a 1850 mAh battery. No PA/FEM — the SX1262 drives a uPG2179 antenna switch from DIO2. The onboard ICM-42607-P/MMC5983MA IMU bus is left powered down (no ZephCore consumer). Untested on hardware; the GNSS UART direction and the display offsets are the two things to check first, both flagged in the board README.

LilyGo T-Impulse Plus (lilygo_timpulse_plus): nRF52840 wristband/tracker with SX1262 (GPIO antenna switch, not DIO2), SSD1315 64x32 OLED, u-blox MIA-M10Q GPS, 4 MB QSPI flash (/ext), touch button, haptic motor. Builds and ships in releases, but several parameters are inferred from vendor sources and not bench-verified (TCXO voltage, battery divider ratio, OLED offsets) — see the board README. Early hardware testing also showed occasional spontaneous reboots, untriaged.

ProMicro LR2021 (promicro_lr2021): nRF52840 SuperMini + Semtech LR2021, the first ZephCore board bring-up for that radio. Source-only — not in build.sh, the release workflow, or the Mesh America catalog, so no release carries a binary for it. The bring-up module was destroyed by an accidental 5V feed (LR2021 VBAT max ~3.7V); build it yourself if you want to continue testing on a fresh module.

ESP32

xiao_esp32c3
xiao_esp32c6/esp32c6/hpcore
xiao_esp32s3/esp32s3/procpu
lilygo_tlora_c6/esp32c6/hpcore
lilygo_t3s3/esp32s3/procpu
station_g2/esp32s3/procpu
heltec_wifi_lora32_v3/esp32s3/procpu
heltec_wifi_lora32_v4/esp32s3/procpu
heltec_wifi_lora32_v43/esp32s3/procpu
heltec_wireless_tracker/esp32s3/procpu
heltec_wireless_tracker_v2/esp32s3/procpu
thinknode_m9/esp32s3/procpu
ttgo_tbeam/esp32/procpu
ttgo_lora32/esp32/procpu   # source-only, no published firmware

ESP32 boards require west blobs fetch hal_espressif before first build.

Heltec V3 console/shell use uart0 (UART serial) in ZephCore.

Heltec Wireless Tracker (heltec_wireless_tracker/esp32s3/procpu): V1.1 ESP32-S3-FN8 companion with SX1262, ST7735R 160x80 TFT, and UC6580 GPS.

Heltec Wireless Tracker V2 (heltec_wireless_tracker_v2/esp32s3/procpu): ESP32-S3FN8 companion with SX1262 + KCT8103L PA/FEM, ST7735R 160x80 TFT, UC6580 GNSS, battery ADC, and USB-C native serial/JTAG.

ThinkNode M9 (thinknode_m9/esp32s3/procpu): ESP32-S3 (16MB flash, 8MB PSRAM) handheld with LR1110, ST7789 320x240 TFT, CC1167Q GPS, PCF8563 RTC, and buzzer. Not yet validated on hardware — see the board README for the bring-up list. The onboard STC8H I2C keyboard, IMU/magnetometer, and SD slot are not ported. The LR1110 radio-firmware updater supports this board (west build -b thinknode_m9/esp32s3/procpu zephcore/tools/lr1110_updater).

LilyGo T-Beam (ttgo_tbeam/esp32/procpu): classic ESP32 (PICO-D4) with SX1262, AXP2101 PMU, and GNSS. Use this for the v1.2 SX1262 variant — the upstream Zephyr DTS models the SX1276 radio, which ZephCore overrides to SX1262 in board.overlay. Console/CLI are on uart0 (onboard USB-UART).

TTGO LoRa32 (ttgo_lora32/esp32/procpu): classic ESP32 (PICO-D4) with SX1276. Console/CLI on uart0.

Source-only — no published firmware, and not a supported configuration. It is deliberately absent from build.sh, the release workflow and the Mesh America catalog, so no release ever carries a binary for it. It is kept in the tree as the one exercise of the SX127x loramac-node radio path, which is old, lacks RX duty cycle and RX gain boost, and gets none of the work the native SX126x/LR11xx/LR20xx drivers do. Build it yourself if you want it; expect to maintain it yourself too.

If you do build the companion, note it is DRAM-bound (~97% of dram0_0_seg) and capped at 50 contacts / 32 queued offline messages — lower than any other companion board. The repeater has no such limit. At the 150/128 this board's config used to declare, it did not link at all. See board.conf for the measured budget before raising either number.

STM32WL

lora_e5_mini

Seeed LoRa-E5 mini (lora_e5_mini): STM32WLE5JC with the integrated SX1262-class sub-GHz radio. No BLE and no USB device — the companion protocol and the CLI both run over USART1 (bridged to USB-C by the onboard USB-UART chip). Flash over SWD/ST-Link with west flash.

MG24 (Silicon Labs)

xiao_mg24

Requires west blobs fetch hal_silabs and pyocd.

nRF54L

xiao_nrf54l15/nrf54l15/cpuapp
me25ls02/nrf54l15/cpuapp

Requires --no-sysbuild flag: west build -b xiao_nrf54l15/nrf54l15/cpuapp zephcore --no-sysbuild

The nRF54L15 has no USB peripheral, so there is no UF2 or DFU path on either board — flash zephyr.hex over SWD. me25ls02 is the MinewSemi ME25LS02 module on its MX25LE02 carrier; its USB-C port is a CH340x UART bridge carrying the console, not a programming port. Untested on hardware.

Native Linux

Not west build -b boards — EXTRA_CONF_FILE presets on top of native_sim for SBCs (Femtofox / Luckfox Pico Mini, Raspberry Pi + RAK6421 HAT). See LINUX_NATIVE.md for build commands and wiring.