Packets not being forwarded were getting included in forwarding stats
calculation and skewing the measurement towards a smaller number.
The latency measurement does not include the batch IO of packets on
send. With a 2ms batching, that will add an average latency of 1ms.
* if RingingTimeout is provided, deadline should be set to that timeout.
This is because the SIP bridge will not return until RingingTimeout
which may be longer than the 30 second default deadline.
* handle Deadline being "before" timeout.
Currently, the signal requests are counted on media side and signal
responses are counted on controller side. This does not provide the
granularity to check how many response messages each media node is
sending.
Seeing some cases where track subscriptions are slow under load. This
would be good to see if the media node is doing a lot of signal response
messages.
publisher peer connection.
While cleaning up during single peer connection changes, unintentionally
removed handler.
Also, another small change to log first packet time adjustment after
increment.
- Move downTrack instantiation to SubscribedTrack as it should own that
DownTrack. Still more to do here as `DownTrack` is fetched from
`SubscribedTrack` in a few places and used. Would like to avoid that,
but doing this initially.
- Use an interface from sfu.Downtrack and replace a bunch of callbacks.
SubscribedTrack is the implementation for DownTrackListener.
Not sure why only that was applying from req which is effectively a
no-op as the clone is a replica of the req. Guess, it was a typo/miss.
Change it to use room preset config value.
* WIP
* check using protocol version
* revert
* clean up
* sdp cid argument
* WIP
* WIP
* test
* clean up
* clean up
* fixes
* clean up
* clean up
* clean up
* conditional checks
* tests for both dual and single peer connection
* test
* test
* test
* type check
* test
* todo
* munges
* combined config
* populate mid
* limit to receive only
* clean up
* clean up
* clean up
* older test
* clean up
* alternative audio codec
* dtx
* don't need to copy
* Anunay feedback
* use the available peer connection
* publisher check
* WIP
* WIP
* WIP
* no mid
* media sections requirement
* mage generate
* WIP
* WIP
* set data channel receive size for test
* handle early media better
* WIP
* do not do ICERestart if no subscriber
* WIP
* WIP
* WIP
* WIP
* WIP
* WIP
* start up subscriber RTCP worker
* WIP
* WIP
* clean up
* clean up
* flag to indicate use of single peer connection
* remove unused interface method
* clean up
* clean up
* Jie feedback #1
* deps
* do not access subscriber in one shot mode
* more places for one shot mode
* more one shot fixes
* deps
* deps
* test
* Populate SDP cid in track info when available.
- Adding SDP cid to TrackInfo. Browsers like FF uses a different stream
id for AddTrack and actual SDP offer. So, have to look up using both
on server side. To make it easier, store both (only if different) in
TrackInfo.
- Use a codec in TrackInfo for audio also. There is some discussion
around doing simulcast codec for audio so that something like PSTN can
use G.711 without any transcoding. So, just keep it consistent between
audio and video.
- Populate SDP cid when SDP offer is received. It could populate a
pending track or an already published track if the new offer is for a
back up codec where the primary codec is already published.
- Passed around parsed offer to more places to avoid parsing multiple
times.
- Clean up MediaTrack interface a bit and remove unneeded methods.
* WIP
* WIP
* deps
* stream allocator mime aware
* clean up
* populate SDP cid before munging
* interface methods
Proper message id checks.
Some refactoring for common code in rtcv2service handlers.
Instantiate signalling based on synchronous local candidates flag, but
needs better defined code.
* More v2 signalling changes
- Use wire message in relay signal
- Generate offerId for SDP for sync mode also
- more checks for SDP offer/answer state to see if there are cases of
missed/duplicate messages
* clean up
* HTTP PATCH on participant sid
* rename
* signal handler
* new files
* clean up
* clean up reassembly
* handle messages on server side
* deps
* staticcheck
* clean up
