* Send connection type to telemetry
When connected, determine how the participant's primary connection is
connected and report it in ParticipantActive event.
* address feedback
* fixed case where prflx is reported instead of relay
* incorporate comments
I don't like using `Target` as direction.
There is one place in code that depends on it.
I am thinking we should add a params `IsOfferer` or something to make it
explicit.
* WIP commit
* WIP commit
* fix copy pasta
* setting PC with previous answer has to happen synchronously
* static check
* WIP commit
* WIP commit
* fixing transport tests
* fix tests and clean up
* minor renaming
* FIx test race
* log event when channel is full
* Export CloseSignalConnection
There are a few places where that close pattern is repeated.
Export it and use that function in other places directly.
* fix test
* Clear disconnect timer on ICERestart
Disconnect timer is set up when a transport fails.
But, it is possible that the connection is resumed.
So, clear disconnect timer on resume.
* clean up
* Start RTCP workers after peer connection connects
* Move more things into transport module
* Start RTCP workers only on connected
* Test needs PeerConnection() method
* adjust comment
* Prevent track subscriptions/adding receivers after close
With subscribe/unsubscribe queuing, a subscribe may be
attempted after a call to `RemoveAllSubscribers`.
So, renaming `RemoveAllSubscribers` to `InitiateClose`
and maintaining state that track is in the process of closing.
* Mime specific remove
* Remove unused error
* do not add receiver when closing
* Promoting a few logs to Info
Also, adding a couple of more info logs which I will remove later
after some debugging.
* mime type
* Protect pause/max layer
* notify even if not bound
- Do not update jitter on padding only packet.
Padding only packet may not have proper timestamp.
If it does, it probably has the time stamp of the
last packet with payload. That will also affect
jitter calculation, i. e. wall clock time is moving,
but RTP time is the same.
- Do not send `onMaxLayer` changed on bind.
It was probably racing with update when max layer
is updated when adaptive stream is off. There is
no need to send that update as the default would
be OFF. It will be enabled when adaptive stream
subscription turns it on or when max layer is
set when down track bind happens and adaptive stream
is off.
* WIP commit
* Connection quality changes
- Fix Firefox showing poor quality
o The issue was that we were using max available layer and
calculating quality. The rationale being that even if
server sends dynacast messages, client may not implement
dynacast and still stream all layers. But, with Firefox
(maybe a Firefox bug), it sends some small amount of
data on layer 2 even when that layer is disabled.
Guessing it is probing (or actually we might be using
some small value for high layers as Firefox cannot turn off
layers). That higher layer gets used in quality calculation.
As the bit rate on that layer is extremely low, it yields low
score.
Fixed by considering the max expected layer. That is of most
interest. Yes, clients may ignore dynacast and stream all layers,
but, max expected is the one of interest. So, look for
quality in the max expected layer and not max available layer.
- Lots of clean up around connection quality stuff
o Use a dynamic scaling thing to ensure that we do not get bitten
by absolute values. Calculate best possible scenario score and
map that to maximum MOS score. This will ensure that different
codecs, different settings do not mess up the scoring. For example,
a client might use 1 Mbps for 720p, but a different client could
use 2 Mbps for 720p. As an SFU/infrastructure middlebox, we do
not have control over quality at those rates. We can only ensure
that streaming happens smoothly at those rates. So, in that
example, for client 1, 1 Mbps will map to MOS 5.0 and for client 2,
2 Mbps will map to MOS 5.0. Any impairments after that will
reflect in the score.
o Penalise for missing target layer by one level for one layer missed.
o Move tests to connection quality directory. The participant test
was not super useful.
* Add missed file
* Remove debug code
* use more constants and initialise normalisation factor
* rtcscore pointer
* Limit dynacast to video and media loss proxy to audio
Was looking at keeping the track type out of those modules
and do a check at a higher level, but it is a bit unwieldy.
So, adding checks to the modules.
Also, ensuring that media loss proxy does not reset unconditionally
every second. Audio RTCP happens once in 5 seconds or so.
So, if server proxied let say 2% at t = 5, t = 6 would have
proxied 0 loss which may or may not be true. So, ensure that
a report was received and proxy value is updated by an actual
report.
* Remove track type from modules
* Filter candidate after setting description
* comment
* Fix filtering candidates
- For offer/answer from remote, do filtering before setting remote
description so that Pion does not see filtered candidates
- For offer/answer originating from server, do filtering after setting
local description (comments in code) so that remote side does not
see filtered candidates.
- Make logging a little consistent and use right context.
* Comment
* TCP fallback config and UT (broken now)
* log SDP only when preferring TCP
* Remove TCP fallback test attempt
* WIP commit
* Refactor media loss proxy
* Use DynacastQuality and MediaLossProxy from MediaTrack
* fix test
* Remove unused param
* Remove unused interfaces
* Move interface methods to local
* Split out DynacastManager
* have to add codec to dynacast manager
* RUnlock
* fix restart
* Adding API to force quality and also maintain closed state
* Address PR comments
David Zhao