Consolidate #ifndef/#ifdef into single #ifdef/#else/#endif block.
Add warning comment to generated header about static linkage.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Move BG_COLOR inline into #ifndef block to avoid unused variable
when HAS_SPLASH_IMAGE is defined. Make show_splash() private since
it's only called internally from init_hardware_only().
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Prevents double PSRAM allocation and LVGL driver re-registration
if init() were called more than once.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Move Display::init_hardware_only() and POWER_EN to right after serial
banner, before GPS/WiFi/SD/Reticulum init. Add 150ms delay after
POWER_EN HIGH so ST7789V power rail stabilizes before SPI commands
(without this, SWRESET is sent to an unpowered chip and silently lost).
Splash now visible for entire boot period (~18s) until LVGL takes over.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Display and LoRa were creating separate SPIClass(HSPI) instances which
claimed GPIO pins via the matrix, preventing SD card (on FSPI) from
accessing MISO after Display init. Now all three peripherals use the
global SPI (FSPI) instance, eliminating GPIO routing conflicts.
- Display: use &SPI instead of new SPIClass(HSPI)
- SX1262Interface: use &SPI instead of new SPIClass(HSPI)
- SDAccess: enable format_if_empty for unformatted cards
Verified on device: SD (128GB SDHC), display, and LoRa all coexist.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
SD card was unresponsive (MISO stuck 0xFF) because Display's HSPI
peripheral had already claimed the GPIO pins via the matrix, preventing
FSPI from routing MISO. Fix by initializing SD card BEFORE Display,
using the global SPI (FSPI) instance — matching LilyGo's reference code.
- Move SD card init before display init in boot sequence
- Use global SPI (FSPI) instead of Display's SPIClass(HSPI)
- Lower SPI frequency to 800kHz matching LilyGo example
- Drive all CS lines (display, LoRa, SD) high before SD init
- Add MISO=38 to Display's SPI.begin for post-init bus sharing
- Add Display::get_spi() accessor for future shared use
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
The T-Deck Plus shares HSPI across the display (CS=12), LoRa (CS=9),
and SD card (CS=39). Previously SD logging was disabled because
SD.begin() reconfigured the SPI bus and blanked the display.
This introduces a FreeRTOS mutex created in main.cpp and injected into
Display, SX1262Interface, and a new SDAccess class so all three
peripherals serialize their SPI transactions safely.
- Add SDAccess class wrapping SD.begin() and file ops with mutex
- Add set_spi_mutex() to Display and SX1262Interface
- Wrap Display flush, fill, draw, and power ops in mutex
- Refactor SDLogger to use SDAccess mutex instead of owning SD.begin()
- Wire up mutex creation and injection order in setup()
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Split T-Deck firmware from microReticulum examples/lxmf_tdeck/ into its
own repo. microReticulum is consumed as a git submodule dependency pinned
to feat/t-deck. All include paths updated from relative symlinks to bare
includes resolved via library build flags.
Both tdeck (NimBLE) and tdeck-bluedroid environments compile successfully.
Licensed under AGPLv3.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Torlando