* attaky_mesh_series: add board variant with FT6636 touch and landscape UI
* attaky_mesh_series: P3 battery (MAX17048) + GPS + shared-I2C mutex
- AttakySharedI2C: one Wire.begin() + a mutex serializing the shared board
I2C bus (SDA=2/SCL=1) across the FT6636 touch poll (core 0), the MAX17048
fuel gauge (core 1), and the future AW9523 keyboard. Arduino's TwoWire
buffers are not concurrency-safe.
- board.begin() owns the authoritative bus init; the touch driver now takes
the lock around every transaction instead of its own Wire.begin().
- getBattMilliVolts(): real MAX17048 VCELL read (78.125 uV/LSB -> mV = raw*5/64),
2 s cache + lock, replacing the 4000 mV stub. Upstream maps mV -> % itself.
Hardware-verified ~4058 mV.
- GPS: rename the dead GPS_BAUD flag to GPS_BAUD_RATE (the core reads that; 9600
only worked via the #else default). Pins verified on hardware: ESP RX = IO17
receives ATGM336H NMEA; MeshCore's module-centric PIN_GPS_TX=17 maps correctly.
* attaky_mesh_series: Control_Keyboard_(Bottom) dual-AW9523 keyboard
Add the Control_Keyboard_(Bottom)_1.0 module as an ADDITIVE hardware
keyboard on the touch board. Two AW9523 expanders (0x5A left / 0x5B
right) each scan a 5x5 matrix over the shared board I2C bus, serialized
through the AttakySharedI2C mutex alongside the FT6636 touch poll and the
MAX17048 fuel gauge.
The driver emits final bytes (printable ASCII, backspace, enter, space)
with momentary Shift resolved to uppercase in-driver. UITask injects them
into the focused textarea exactly like the web-mirror keystroke path, so
CAP_KEYBOARD stays 0 and the on-screen keyboard is not suppressed (touch
typing does not regress). Focus-gated: the matrices are only scanned
while an editable field is bound, so a key has zero side effect when
nothing is focused.
Hardware-verified, both halves: q/w/e/r/t (0x5A) + y (0x5B), Shift
uppercase, backspace, space, enter; on-screen keyboard intact.
* attaky_mesh_series: use reliable 115200 upload speed
* attaky_mesh_series: use core default GPS baud
* attaky_mesh_series: restore GPS_BAUD setting
* attaky_mesh_series: rename PlatformIO environment
The V4-R8 uses an ESP32-S3R8 (8 MB OCTAL PSRAM) which claims GPIO33-37, so
Heltec moved every control signal off them and the Expansion Kit V2 rebuilt the
display/touch/SD block onto a hardware-SPI bus:
Vext 36->40 (active-LOW) . GPS_EN 34->42 . LED 35->46 . ADC_Ctrl removed
TFT (LovyanGFX HW-SPI): MOSI=15 SCK=16 MISO=45 CS=47 DC=48 RST=21 BL=44
touch (CHSC6x, shares board I2C 17/18) . micro-SD (shared TFT SPI, CS=3)
The build defines HELTEC_LORA_V4_TFT too, so it reuses all the V4 touch-UI code;
HELTEC_LORA_V4_R8 gates only the deltas. 8 MB enables the on-device web browser
(CAP_WEB_BROWSER) and the SD card (CAP_SD). Also wires the board into the release
+ web-flasher pipeline (release.sh, gen-flasher-meta.py, the flasher picker).
UNTESTED — no V4-R8 hardware yet. Pin sources: Meshtastic heltec_v4_r8 variant,
Heltec V4-R8 pinmap, and the Expansion_board_V2.03 schematic. All three touch
envs build clean; V4/T-Deck unregressed. On-device TODO: CHSC6x shared-Wire on
17/18, SD_CS=3, and the V2 PAM8904 buzzer.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- PIN_USER_BTN: -1 -> 0 (enable BOOT key on GPIO0)
- Short press (<1s): toggle screen on/off (no hard-lock)
- Long press (>=1s): open power menu (Power off / Reboot / Cancel)
- Add ARDUINO_USB_CDC_ON_BOOT=1 (stable USB CDC COM port)
- boards/rak_tap_v2.json: use_1200bps_touch=false, wait_for_upload_port=false
(manual download mode via BOOT+RESET, esptool upload on COM7)
- Remove unused boards/wiscore_rak3312.json
- Remove LovyanGFX from Heltec lib_deps (accidental regression in baseline)
Signed-off-by: Ethan-chen1234-zy <ethan.chen@rakwireless.com>
[env:tlora_pager_lr1121_companion_radio_touch], cloned from the T-Deck
env with board/radio/display/GPS deltas for the LR1121 + ST7796 pager.
Two structural fixes were needed to actually get this to compile:
- pins_arduino.h moves to its own variants/lilygo_tlora_pager_pins/
folder (board JSON's "variant" field updated to match). PlatformIO's
arduino-esp32 build script unconditionally compiles every source
file under board_build.variants_dir/<board.variant>/ as a separate
framework-level library with none of our own lib_deps -- since this
board (unlike T-Deck/Heltec, which point at framework-bundled
variants) has no framework-bundled variant of its own, our
variants_dir override was colliding with our own board-glue files
and failing to find Wire.h/RadioLib.h.
- CustomLR1121Wrapper.h's bare quoted includes of RadioLibWrappers.h/
LR11x0Reset.h only resolve for core-lib files living in the same
directory as their targets; switched to angle-bracket includes with
the full core-lib subpath.
Also required one small, forced addition to UITask.cpp: its display
class selection only recognized the Tanmatsu vs. everything-else split,
which made this env's own hard compile gate unreachable. Added a single
#elif arm for the pager's display type: no other UITask.cpp behavior
changes, indev/resolution/layout wiring is still a later milestone.
All three envs (Heltec V4, T-Deck, pager) build green.
Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
New board: ThinkNode_M9_companion_radio_touch env, variants/thinknode_m9/
(board glue, LR1110 target, keyboard driver, partitions, M9_PORT.md pin
reference), boards/thinknode_m9.json, device_caps HAS_THINKNODE_M9 block,
HAS_M9_KEYBOARD input path in the touch UI (d-pad focus nav, tab jump keys,
QWERTY typing).
Based on a contributed bring-up patch by ded (SalishMesh), who also remote-
tested every build on a preproduction unit. Hard-won fixes on top of the
patch, each verified on hardware:
- LR1110 radio init -706: preprod chips run transceiver FW 0x0303, which
rejects DriveDiosInSleepMode (0x012A, added in FW 0x0308) that RadioLib
7.x sends unconditionally during begin(). New build-time patch
scripts/build/patch_radiolib_lr11x0.py tolerates it on old FW;
radio_init() prints the chip's device/FW/errors either way.
- TCXO: DIO3 at 3.3 V (the patch's active-oscillator/tcxo=0 theory gave
-707 on hardware).
- Display: rotation 1 (not 3), plus the missing landscape s_ui_rotation
override so LVGL renders 320x240 instead of portrait-into-landscape.
- Keyboard: the controller is a separate ESP32-S2 I2C slave (0x6C) with
addressed registers - reads select register 0x01 first (bare reads
return the HW-version register forever). Boot probe logs the
controller's HW/FW; backlight duty register wired.
- USB pad release: the keyboard bus lives on GPIO20/21 = the S3's native
USB D-/D+ pads, owned from reset by the ROM USB-Serial-JTAG (D+ pullup
on SDA). M9Board::begin() releases them before any bus init.
- GPIO35-37 are octal-PSRAM pins on the S3R8 - never drive them (the
patch's "SD CS = 36" misread package pin 36 = GPIO48; SD is on the
shared SPI bus, support returns with PIN_SD_CS=48 later).
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Board class, pins, and partition table for the LilyGo T-LoRa Pager
(ESP32-S3, LR1121 radio variant), modeled on the T-Deck's shape.
TLoraPagerBoard brings up the XL9555 power-rail expander and BQ27220
fuel gauge over I2C (this board has no VBAT ADC divider). Nothing
references these files yet, so the shipping T-Deck/Heltec V4 envs are
unaffected; radio/display/env wiring land in follow-up commits.
Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
Headline: full keyboard navigation (on by default) — WASDZ spatial focus move, S select,
Q back, per-tab hotkeys (E/R/T/U/I) shown on the icons, plus scroll up/down (F/C). Every
key is remappable in Settings -> Keyboard. Foundation for keyboard-first devices like the
Tanmatsu T-Pager (no touchscreen) and a reliable keyboard workflow on the T-Deck today.
Also: #27 receive/flood reboot fix, on-boot crash-report prompt, map zoom +/- buttons (#26),
route-replay wide overview, 'App drawer as home' option. The in-progress Tanmatsu (ESP32-P4)
port source is now public. Mesh America catalog + release.sh kept from main.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
The repo carried the full MeshCore board matrix (~38 defs) inherited from the
monorepo split; only heltec_v4 + t-deck are referenced by the two touch envs.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
First board lands. wadamesh builds the LVGL touch firmware as its own project,
consuming the MeshCore core via lib_deps @ git tag (ALLFATHER-BV/MeshCore
#v1.16.0-wada.0) — no vendored core in this repo. Output is byte-identical to the
in-tree meshcomod build (delta = embedded build-path strings only).
Contents: companion_radio app (MyMesh/main/DataStore), ui-touch LVGL UI,
variants/heltec_v4 board glue, boards/heltec_v4.json, lv_conf, the bundled
ed25519 lib, AsyncElegantOTA, partition table, and a flattened platformio.ini
for env heltec_v4_tft_companion_radio_usb_tcp_touch.
MeshCore-derived files (app glue) remain MIT; ui-touch is GPL — see NOTICE.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Signed-off-by: Kaj Schittecat <kaj@schittecat.com>
Michael A. Cojocari