deploy: dd4554a1a7

cli_commands/index.html

@@ -9303,6 +9303,31 @@ hardware busy-result count.</p>
 <p><strong>Parameters:</strong>
 - <code>value</code>: Interval in seconds, 0-1020, rounded down to a multiple of 4 (17 becomes 16). 0 to disable.</p>
 <p><strong>Default:</strong> <code>0.0</code></p>
+<p>With device <code>powersaving</code> on and a nonzero AGC interval, Companion, Repeater,
+Room Server, and Sensor firmware use adaptive reset scheduling. The saved
+interval is the starting/minimum interval. After every two admitted maintenance
+attempts without an observed radio recovery, the interval doubles, capped at
+60 seconds (or the saved interval if it is already longer). For example,
+8 -&gt; 16 -&gt; 32 -&gt; 60 seconds, with two attempts at each step. An observed radio
+recovery returns the schedule to the saved interval. Changing the interval or
+power-saving mode starts a fresh schedule; adaptive history is not persisted.</p>
+<p><code>get agc.reset.interval</code> still reports the saved starting interval, not the
+current adaptive interval. <code>0</code> disables periodic AGC maintenance even with
+power saving on. With power saving off, fixed-interval behavior is retained.
+This follows device <code>powersaving</code>, independently of LoRa <code>radio.rxps</code>.</p>
+<p>Adaptive scheduling does not treat a quiet mesh, strong packets, a stable
+noise floor, or a successful transmission as proof of full receiver sensitivity.
+TX cannot continually postpone adaptive maintenance. Pending RX/TX, a BUSY
+chip outside known RX duty cycling, carrier/Morse ownership, and an active
+noise-floor block can defer it; deferred attempts do not advance backoff and
+are retried after 50 ms. The
+60-second bound is a scheduling interval, not permission to interrupt a packet.
+An armed RXPS radio uses the existing explicit wake/reset path, avoiding retry
+polling that could miss every short listen window.
+Existing radio recovery watchdogs remain active. These conservative intervals
+have host regression coverage, but are not hardware-qualified sensitivity or
+battery-life results; noisy sites may require a short fixed interval with
+device power saving off.</p>
 <hr />
 <h4 id="view-or-change-the-radio-watchdog-interval-mqtt-observer-only">View or change the radio watchdog interval (MQTT observer only)</h4>
 <p><strong>Usage:</strong>

search/search_index.json

@@ -1 +1 @@
-{"config":{"lang":["en"],"separator":"[\\s\\-]+","pipeline":["stopWordFilter"],"fields":{"title":{"boost":1000.0},"text":{"boost":1.0},"tags":{"boost":1000000.0}}},"docs":[{"location":"","title":"Home","text":"<p>View this page on MeshCore Docs.</p>"},{"location":"#meshcore-documentation","title":"MeshCore documentation","text":"<p>Choose firmware with the firmware picker. For help with a device already in service, start with the FAQ.</p>"},{"location":"#current-release","title":"Current release","text":"<ul> <li>1.17.1.8 USA Cascade release notes</li> <li>Test Results \u2014 validation archive and 1.17.1.8 Preview 1 qualification evidence</li> </ul>"},{"location":"#documentation","title":"Documentation","text":"<ul> <li>Feature switches by role and Full Companion features</li> <li>Firmware update guide, easy LoRa OTA, and scripted LoRa OTA</li> <li>CLI commands, availability by build, and radio profiles</li> <li>Private fleet management: signed filtering and secondary-radio commands for a fleet or one node</li> <li>Room history, moderation, and information board: optional persistent chat and local Wi-Fi room access</li> <li>Companion protocol, packet format, and QR codes</li> </ul> <p>The navigation groups the remaining guides under Documentation, including board-specific updates, networking, power, and protocol references.</p>"},{"location":"#tools","title":"Tools","text":"<ul> <li>Firmware picker and USB web console</li> <li>Notification builder and temporary radio test builder</li> <li>Filter policy playground, telemetry decoder, and management report decoder</li> </ul>"},{"location":"#engineering-records","title":"Engineering records","text":"<ul> <li>Research \u2014 design notes, diagnostics, and historical update-chain studies</li> <li>Old Releases \u2014 historical release notes and supporting files</li> </ul> <p>Found a mistake or missing information? Edit the documentation.</p>"},{"location":"WiFi/","title":"WiFi","text":"<p>View this page on MeshCore Docs.</p>"},{"location":"WiFi/#wifi-and-mqtt-by-firmware-type","title":"WiFi and MQTT by Firmware Type","text":"<p>MeshCore itself does not require WiFi or the internet. LoRa packet exchange, repeating, room servers, companions, and sensors can all operate without either. WiFi is added by particular ESP32 firmware targets for one or more of these purposes:</p> <ul> <li>a TCP connection between a WiFi companion and a phone or computer;</li> <li>the WebConfig browser interface;</li> <li>MQTT uplinking from the radio to internet or LAN brokers;</li> <li>WiFi-assisted OTA services on builds that include them;</li> <li>ESP-NOW bridging, which uses the ESP32's 2.4 GHz radio but is not a connection   to a WiFi access point.</li> </ul> <p>The firmware role and the build profile are separate choices. USB logging does not itself provide MQTT. MQTT-capable Full Companions include that feature without <code>mqtt</code> in their filename; check the artifact capability manifest. See feature switches by role for the different Companion and infrastructure controls and the USB web console.</p>"},{"location":"WiFi/#quick-reference","title":"Quick reference","text":"Firmware target or role Infrastructure WiFi MQTT What WiFi does <code>*_repeater</code> Build-dependent on ESP32 No FULL builds provide WebConfig, browser OTA, and the TCP 5001 LoRa-OTA seeder while WiFi is active <code>*_repeater_observer_mqtt</code> Yes Yes Uplinks heard and selected transmitted LoRa packets; repeating remains enabled by default <code>*_room_server</code> Build-dependent on ESP32 No FULL builds provide WebConfig, browser OTA, and the TCP 5001 LoRa-OTA seeder while WiFi is active <code>*_room_server_observer_mqtt</code> Yes Yes Runs the room server and uplinks radio traffic <code>*_companion_radio_wifi</code> Yes No Exposes the MeshCore companion protocol on TCP port 5000 <code>*_companion_radio_wifi_mqtt</code> Yes Yes Runs both the TCP companion interface and the MQTT uplink <code>*_companion_radio_full*</code> ESP32, subject to board/transport selection Where compiled on ESP32 Includes supported USB/wireless transports; configure MQTT through WebConfig Dedicated USB, BLE, or serial companion (not Full) No No Uses the transport named by the target instead <code>*_repeater_bridge_espnow</code> Build-dependent on ESP32 No Uses ESP-NOW for its bridge; <code>bridge.format wrapped|raw</code> selects legacy bridge framing or primary-ESP-NOW compatibility; a FULL build also exposes the TCP 5001 LoRa-OTA seeder whenever WiFi is usable RS232 bridge No No Bridges through a serial interface Ethernet repeater/room server No WiFi No Uses wired Ethernet for its role-specific network interface <code>*_sensor</code> Build-dependent on ESP32 No A FULL ESP32 sensor can expose the TCP 5001 LoRa-OTA seeder through its browser-OTA setup AP Terminal-chat or KISS modem No in current targets No Uses LoRa and its role-specific local interface <code>*_lora_ota_no_external_sensors</code> On demand on ESP32 No LeaLine truncated
+{"config":{"lang":["en"],"separator":"[\\s\\-]+","pipeline":["stopWordFilter"],"fields":{"title":{"boost":1000.0},"text":{"boost":1.0},"tags":{"boost":1000000.0}}},"docs":[{"location":"","title":"Home","text":"<p>View this page on MeshCore Docs.</p>"},{"location":"#meshcore-documentation","title":"MeshCore documentation","text":"<p>Choose firmware with the firmware picker. For help with a device already in service, start with the FAQ.</p>"},{"location":"#current-release","title":"Current release","text":"<ul> <li>1.17.1.8 USA Cascade release notes</li> <li>Test Results \u2014 validation archive and 1.17.1.8 Preview 1 qualification evidence</li> </ul>"},{"location":"#documentation","title":"Documentation","text":"<ul> <li>Feature switches by role and Full Companion features</li> <li>Firmware update guide, easy LoRa OTA, and scripted LoRa OTA</li> <li>CLI commands, availability by build, and radio profiles</li> <li>Private fleet management: signed filtering and secondary-radio commands for a fleet or one node</li> <li>Room history, moderation, and information board: optional persistent chat and local Wi-Fi room access</li> <li>Companion protocol, packet format, and QR codes</li> </ul> <p>The navigation groups the remaining guides under Documentation, including board-specific updates, networking, power, and protocol references.</p>"},{"location":"#tools","title":"Tools","text":"<ul> <li>Firmware picker and USB web console</li> <li>Notification builder and temporary radio test builder</li> <li>Filter policy playground, telemetry decoder, and management report decoder</li> </ul>"},{"location":"#engineering-records","title":"Engineering records","text":"<ul> <li>Research \u2014 design notes, diagnostics, and historical update-chain studies</li> <li>Old Releases \u2014 historical release notes and supporting files</li> </ul> <p>Found a mistake or missing information? Edit the documentation.</p>"},{"location":"WiFi/","title":"WiFi","text":"<p>View this page on MeshCore Docs.</p>"},{"location":"WiFi/#wifi-and-mqtt-by-firmware-type","title":"WiFi and MQTT by Firmware Type","text":"<p>MeshCore itself does not require WiFi or the internet. LoRa packet exchange, repeating, room servers, companions, and sensors can all operate without either. WiFi is added by particular ESP32 firmware targets for one or more of these purposes:</p> <ul> <li>a TCP connection between a WiFi companion and a phone or computer;</li> <li>the WebConfig browser interface;</li> <li>MQTT uplinking from the radio to internet or LAN brokers;</li> <li>WiFi-assisted OTA services on builds that include them;</li> <li>ESP-NOW bridging, which uses the ESP32's 2.4 GHz radio but is not a connection   to a WiFi access point.</li> </ul> <p>The firmware role and the build profile are separate choices. USB logging does not itself provide MQTT. MQTT-capable Full Companions include that feature without <code>mqtt</code> in their filename; check the artifact capability manifest. See feature switches by role for the different Companion and infrastructure controls and the USB web console.</p>"},{"location":"WiFi/#quick-reference","title":"Quick reference","text":"Firmware target or role Infrastructure WiFi MQTT What WiFi does <code>*_repeater</code> Build-dependent on ESP32 No FULL builds provide WebConfig, browser OTA, and the TCP 5001 LoRa-OTA seeder while WiFi is active <code>*_repeater_observer_mqtt</code> Yes Yes Uplinks heard and selected transmitted LoRa packets; repeating remains enabled by default <code>*_room_server</code> Build-dependent on ESP32 No FULL builds provide WebConfig, browser OTA, and the TCP 5001 LoRa-OTA seeder while WiFi is active <code>*_room_server_observer_mqtt</code> Yes Yes Runs the room server and uplinks radio traffic <code>*_companion_radio_wifi</code> Yes No Exposes the MeshCore companion protocol on TCP port 5000 <code>*_companion_radio_wifi_mqtt</code> Yes Yes Runs both the TCP companion interface and the MQTT uplink <code>*_companion_radio_full*</code> ESP32, subject to board/transport selection Where compiled on ESP32 Includes supported USB/wireless transports; configure MQTT through WebConfig Dedicated USB, BLE, or serial companion (not Full) No No Uses the transport named by the target instead <code>*_repeater_bridge_espnow</code> Build-dependent on ESP32 No Uses ESP-NOW for its bridge; <code>bridge.format wrapped|raw</code> selects legacy bridge framing or primary-ESP-NOW compatibility; a FULL build also exposes the TCP 5001 LoRa-OTA seeder whenever WiFi is usable RS232 bridge No No Bridges through a serial interface Ethernet repeater/room server No WiFi No Uses wired Ethernet for its role-specific network interface <code>*_sensor</code> Build-dependent on ESP32 No A FULL ESP32 sensor can expose the TCP 5001 LoRa-OTA seeder through its browser-OTA setup AP Terminal-chat or KISS modem No in current targets No Uses LoRa and its role-specific local interface <code>*_lora_ota_no_external_sensors</code> On demand on ESP32 No LeaLine truncated

test-results/radio_receive_calibration/index.html

@@ -2298,8 +2298,10 @@ gain/tuning changes, AGC resets, and radio recovery still request a fresh block
 promptly. Dual-profile scanning retains
 its separate refresh policy.</p>
 <p>Frequent configured AGC resets can still dominate calibration time: Cascade
-repeater builds default to an eight-second AGC interval, and MQTT observers
-use 28 seconds. Those resets are not throttled by the routine cooldown. After
+repeater builds start with an eight-second AGC interval, and MQTT observers
+use 28 seconds. With device power saving on, their adaptive AGC schedule backs
+off separately, up to 60 seconds; see <a href="../../cli_commands/">AGC reset settings</a>.
+AGC resets still bypass the routine noise-floor cooldown. After
 a timed-out startup block with no valid floor, the next routine RXPS attempt
 also waits 60 seconds; passive retries retain their existing bounded busy
 escape while waiting for a valid baseline.</p>