deploy: ac0daf3cef

companion_radio_full/index.html

@@ -3461,6 +3461,11 @@ physical display use <code>123456</code>. Use <code>set pin 654321</code> in the
 a fixed pairing PIN, then <code>reboot</code> to activate it. <code>set pin 0</code> restores the
 default/generated PIN policy. A PIN saved through the Companion protocol also
 takes effect after reboot. See the <a href="../cli_commands/#set-the-bluetooth-pairing-pin-companion">PIN command reference</a>.</p>
+<p>On T1000-E, a USB data host automatically pauses Bluetooth, including an
+existing phone connection. Unplug USB to resume Bluetooth after 500 ms; a
+saved off setting stays off. A wall charger without a USB data host does not
+pause Bluetooth. See the <a href="../role_feature_switches/">T1000-E transport policy</a>
+for status and saved-setting behavior.</p>
 <p>The Bluetooth device name is independently configurable. In the text terminal,
 use <code>get bluetooth.name</code> and <code>set bluetooth.name &lt;name&gt;</code>; use
 <code>set bluetooth.name default</code> to restore <code>MeshCore-&lt;node name&gt;</code>. The WebConfig

role_feature_switches/index.html

@@ -2835,6 +2835,13 @@ Plain <code>off</code> requires another active management connection;
 See <a href="../cli_commands/#turn-bluetooth-on-or-off-companion">Bluetooth controls</a>
 for reply draining and boot-transport restrictions. Ethernet controls remain
 specific to the board's recipe; there is no universal Ethernet-off command.</p>
+<p><strong>T1000-E Companion:</strong> USB data takes priority over Bluetooth. Once a computer
+enumerates USB, the firmware stops Bluetooth advertising and disconnects any
+Bluetooth client, even if no serial application is open. Bluetooth resumes
+500 ms after USB disconnects, unless it was switched off manually. Battery
+power and a charge-only wall supply leave Bluetooth available. The saved
+Bluetooth setting, pairing PIN and bonds are preserved. <code>get bluetooth</code>
+reports the USB pause; <code>set bluetooth on</code> saves the choice for after unplugging.</p>
 <p><strong>SenseCAP Indicator Full only:</strong> <code>set companion.transport wifi</code> followed by
 <code>reboot</code> selects WiFi; <code>set companion.transport ble</code> followed by <code>reboot</code>
 selects Bluetooth. Check <code>get companion.transport</code>. USB remains available.

search/search_index.json

@@ -1 +1 @@
-{"config":{"lang":["en"],"separator":"[\\s\\-]+","pipeline":["stopWordFilter"],"fields":{"title":{"boost":1000.0},"text":{"boost":1.0},"tags":{"boost":1000000.0}}},"docs":[{"location":"","title":"Home","text":"<p>View this page on MeshCore Docs.</p>"},{"location":"#meshcore-documentation","title":"MeshCore documentation","text":"<p>Choose firmware with the firmware picker. For help with a device already in service, start with the FAQ.</p>"},{"location":"#current-release","title":"Current release","text":"<ul> <li>1.17.1.8 USA Cascade release notes</li> <li>Test Results \u2014 validation archive and 1.17.1.8 Preview 1 qualification evidence</li> </ul>"},{"location":"#documentation","title":"Documentation","text":"<ul> <li>Feature switches by role and Full Companion features</li> <li>Firmware update guide, easy LoRa OTA, and scripted LoRa OTA</li> <li>CLI commands, availability by build, and radio profiles</li> <li>Private fleet management: signed filtering and secondary-radio commands for a fleet or one node</li> <li>Room history, moderation, and information board: optional persistent chat and local Wi-Fi room access</li> <li>Companion protocol, packet format, and QR codes</li> </ul> <p>The navigation groups the remaining guides under Documentation, including board-specific updates, networking, power, and protocol references.</p>"},{"location":"#tools","title":"Tools","text":"<ul> <li>Firmware picker and USB web console</li> <li>Notification builder and temporary radio test builder</li> <li>Filter policy playground, telemetry decoder, and management report decoder</li> </ul>"},{"location":"#engineering-records","title":"Engineering records","text":"<ul> <li>Research \u2014 design notes, diagnostics, and historical update-chain studies</li> <li>Old Releases \u2014 historical release notes and supporting files</li> </ul> <p>Found a mistake or missing information? Edit the documentation.</p>"},{"location":"WiFi/","title":"WiFi","text":"<p>View this page on MeshCore Docs.</p>"},{"location":"WiFi/#wifi-and-mqtt-by-firmware-type","title":"WiFi and MQTT by Firmware Type","text":"<p>MeshCore itself does not require WiFi or the internet. LoRa packet exchange, repeating, room servers, companions, and sensors can all operate without either. WiFi is added by particular ESP32 firmware targets for one or more of these purposes:</p> <ul> <li>a TCP connection between a WiFi companion and a phone or computer;</li> <li>the WebConfig browser interface;</li> <li>MQTT uplinking from the radio to internet or LAN brokers;</li> <li>WiFi-assisted OTA services on builds that include them;</li> <li>ESP-NOW bridging, which uses the ESP32's 2.4 GHz radio but is not a connection   to a WiFi access point.</li> </ul> <p>The firmware role and the build profile are separate choices. USB logging does not itself provide MQTT. MQTT-capable Full Companions include that feature without <code>mqtt</code> in their filename; check the artifact capability manifest. See feature switches by role for the different Companion and infrastructure controls and the USB web console.</p>"},{"location":"WiFi/#quick-reference","title":"Quick reference","text":"Firmware target or role Infrastructure WiFi MQTT What WiFi does <code>*_repeater</code> Build-dependent on ESP32 No FULL builds provide WebConfig, browser OTA, and the TCP 5001 LoRa-OTA seeder while WiFi is active <code>*_repeater_observer_mqtt</code> Yes Yes Uplinks heard and selected transmitted LoRa packets; repeating remains enabled by default <code>*_room_server</code> Build-dependent on ESP32 No FULL builds provide WebConfig, browser OTA, and the TCP 5001 LoRa-OTA seeder while WiFi is active <code>*_room_server_observer_mqtt</code> Yes Yes Runs the room server and uplinks radio traffic <code>*_companion_radio_wifi</code> Yes No Exposes the MeshCore companion protocol on TCP port 5000 <code>*_companion_radio_wifi_mqtt</code> Yes Yes Runs both the TCP companion interface and the MQTT uplink <code>*_companion_radio_full*</code> ESP32, subject to board/transport selection Where compiled on ESP32 Includes supported USB/wireless transports; configure MQTT through WebConfig Dedicated USB, BLE, or serial companion (not Full) No No Uses the transport named by the target instead <code>*_repeater_bridge_espnow</code> Build-dependent on ESP32 No Uses ESP-NOW for its bridge; <code>bridge.format wrapped|raw</code> selects legacy bridge framing or primary-ESP-NOW compatibility; a FULL build also exposes the TCP 5001 LoRa-OTA seeder whenever WiFi is usable RS232 bridge No No Bridges through a serial interface Ethernet repeater/room server No WiFi No Uses wired Ethernet for its role-specific network interface <code>*_sensor</code> Build-dependent on ESP32 No A FULL ESP32 sensor can expose the TCP 5001 LoRa-OTA seeder through its browser-OTA setup AP Terminal-chat or KISS modem No in current targets No Uses LoRa and its role-specific local interface <code>*_lora_ota_no_external_sensors</code> On demand on ESP32 No LeaLine truncated
+{"config":{"lang":["en"],"separator":"[\\s\\-]+","pipeline":["stopWordFilter"],"fields":{"title":{"boost":1000.0},"text":{"boost":1.0},"tags":{"boost":1000000.0}}},"docs":[{"location":"","title":"Home","text":"<p>View this page on MeshCore Docs.</p>"},{"location":"#meshcore-documentation","title":"MeshCore documentation","text":"<p>Choose firmware with the firmware picker. For help with a device already in service, start with the FAQ.</p>"},{"location":"#current-release","title":"Current release","text":"<ul> <li>1.17.1.8 USA Cascade release notes</li> <li>Test Results \u2014 validation archive and 1.17.1.8 Preview 1 qualification evidence</li> </ul>"},{"location":"#documentation","title":"Documentation","text":"<ul> <li>Feature switches by role and Full Companion features</li> <li>Firmware update guide, easy LoRa OTA, and scripted LoRa OTA</li> <li>CLI commands, availability by build, and radio profiles</li> <li>Private fleet management: signed filtering and secondary-radio commands for a fleet or one node</li> <li>Room history, moderation, and information board: optional persistent chat and local Wi-Fi room access</li> <li>Companion protocol, packet format, and QR codes</li> </ul> <p>The navigation groups the remaining guides under Documentation, including board-specific updates, networking, power, and protocol references.</p>"},{"location":"#tools","title":"Tools","text":"<ul> <li>Firmware picker and USB web console</li> <li>Notification builder and temporary radio test builder</li> <li>Filter policy playground, telemetry decoder, and management report decoder</li> </ul>"},{"location":"#engineering-records","title":"Engineering records","text":"<ul> <li>Research \u2014 design notes, diagnostics, and historical update-chain studies</li> <li>Old Releases \u2014 historical release notes and supporting files</li> </ul> <p>Found a mistake or missing information? Edit the documentation.</p>"},{"location":"WiFi/","title":"WiFi","text":"<p>View this page on MeshCore Docs.</p>"},{"location":"WiFi/#wifi-and-mqtt-by-firmware-type","title":"WiFi and MQTT by Firmware Type","text":"<p>MeshCore itself does not require WiFi or the internet. LoRa packet exchange, repeating, room servers, companions, and sensors can all operate without either. WiFi is added by particular ESP32 firmware targets for one or more of these purposes:</p> <ul> <li>a TCP connection between a WiFi companion and a phone or computer;</li> <li>the WebConfig browser interface;</li> <li>MQTT uplinking from the radio to internet or LAN brokers;</li> <li>WiFi-assisted OTA services on builds that include them;</li> <li>ESP-NOW bridging, which uses the ESP32's 2.4 GHz radio but is not a connection   to a WiFi access point.</li> </ul> <p>The firmware role and the build profile are separate choices. USB logging does not itself provide MQTT. MQTT-capable Full Companions include that feature without <code>mqtt</code> in their filename; check the artifact capability manifest. See feature switches by role for the different Companion and infrastructure controls and the USB web console.</p>"},{"location":"WiFi/#quick-reference","title":"Quick reference","text":"Firmware target or role Infrastructure WiFi MQTT What WiFi does <code>*_repeater</code> Build-dependent on ESP32 No FULL builds provide WebConfig, browser OTA, and the TCP 5001 LoRa-OTA seeder while WiFi is active <code>*_repeater_observer_mqtt</code> Yes Yes Uplinks heard and selected transmitted LoRa packets; repeating remains enabled by default <code>*_room_server</code> Build-dependent on ESP32 No FULL builds provide WebConfig, browser OTA, and the TCP 5001 LoRa-OTA seeder while WiFi is active <code>*_room_server_observer_mqtt</code> Yes Yes Runs the room server and uplinks radio traffic <code>*_companion_radio_wifi</code> Yes No Exposes the MeshCore companion protocol on TCP port 5000 <code>*_companion_radio_wifi_mqtt</code> Yes Yes Runs both the TCP companion interface and the MQTT uplink <code>*_companion_radio_full*</code> ESP32, subject to board/transport selection Where compiled on ESP32 Includes supported USB/wireless transports; configure MQTT through WebConfig Dedicated USB, BLE, or serial companion (not Full) No No Uses the transport named by the target instead <code>*_repeater_bridge_espnow</code> Build-dependent on ESP32 No Uses ESP-NOW for its bridge; <code>bridge.format wrapped|raw</code> selects legacy bridge framing or primary-ESP-NOW compatibility; a FULL build also exposes the TCP 5001 LoRa-OTA seeder whenever WiFi is usable RS232 bridge No No Bridges through a serial interface Ethernet repeater/room server No WiFi No Uses wired Ethernet for its role-specific network interface <code>*_sensor</code> Build-dependent on ESP32 No A FULL ESP32 sensor can expose the TCP 5001 LoRa-OTA seeder through its browser-OTA setup AP Terminal-chat or KISS modem No in current targets No Uses LoRa and its role-specific local interface <code>*_lora_ota_no_external_sensors</code> On demand on ESP32 No LeaLine truncated