dandri/MeshCore-mqtt-observer
1
0
Fork 0
mirror of https://github.com/agessaman/MeshCore.git synced 2026-08-24 11:40:06 +00:00
Code Issues Packages Projects Releases Wiki Activity
3,340 Commits 31 Branches 3 Tags
dev
Commit Graph
3340 Commits
This Branch
This Branch
All Branches
Author SHA1 Message Date
Huw DuddyandGitHub 45c0c32354 Merge pull request #3218 from fkallay1/fix/lr2021-set-tx-power-rx-stall 
Fix LR2021 occasionally stopping reception after a TX power change
 2026-08-17 23:20:32 +10:00
Huw DuddyandGitHub 9387f55d7e trimmed comment 2026-08-17 23:16:01 +10:00
Fedor Kallay 114093ee0e fix(lr2021): setTxPower() could leave the receiver down until reboot 
RadioLibWrapper::setTxPower() called setOutputPower() and nothing else. On
LR2021 that writes the PA config and TxParams, which are standby-only commands,
and it never re-arms the receiver.

This only affects LR2021 boards. recvRaw() has:

    #if defined(USE_LR2021)
      state = STATE_RX;    // LR2021 stays in Rx after readData
    #else
      state = STATE_IDLE;  // need another startReceive()
    #endif

so on SX126x the next recvRaw() re-arms Rx anyway and the write is harmless,
while on LR2021 startReceive() is never called again on its own. A 'set tx'
issued while the radio was listening could therefore stop reception until the
next reboot. Observed a few times on an LR2021 repeater; recovery required a
power cycle.

Dispatcher's stuck-radio check does not catch it: isInRecvMode() reports the
wrapper's own `state` flag rather than the chip's actual mode, so it still
believes the radio is in Rx, and it only raises ERR_EVENT_STARTRX_TIMEOUT
without attempting recovery.

Fix: on LR2021, drop to standby via idle() before writing the PA config and let
checkRecv() re-arm Rx - the same pattern resetAGC() and
applySideDetectorConfig() already use. Other radios are left untouched.

Affects meshtracker_x1 and meshnology_w12 (both USE_LR2021).

Tested on hardware with an LR2021 repeater: six consecutive 'set tx' changes
(15/18/21/14/19/14), after which the radio kept receiving and forwarding
traffic (rawrx/rxpkts increasing, no missed IRQs). Noise-floor sampling also
kept updating, which only happens while state == STATE_RX.
 2026-08-15 02:31:19 +02:00
Scott Powell d929643524 * version 1.17.1 mbedtls-4k 2026-08-14 22:19:19 +10:00
Huw DuddyandGitHub 24bdc24b39 Merge pull request #3206 from meshcore-dev/nrf-combine-rng-entropy 
combine radio's entropy with CC310 RNG
 2026-08-14 22:09:26 +10:00
Scott Powell fcb9bdf209 * combine radio's entropy with CC310 RNG 2026-08-14 17:46:43 +10:00
Huw DuddyandGitHub 50a51a6479 Merge pull request #3203 from meshcore-dev/companion-fem-pref-fix 
commenting out the load/save of the fem_ properties
 2026-08-14 16:44:59 +10:00
Scott Powell e78bff0041 * unit test no longer valid 2026-08-14 16:42:54 +10:00
Scott Powell 890a2e2cff * commenting out the load/save of the fem_ properties, until they can be set 2026-08-14 16:30:12 +10:00
ripplebizandGitHub b09cb27a1f Merge pull request #3106 from ViezeVingertjes/fix/scoped-reply-routing 
Fix replies dropped when flood.max.unscoped is low
 2026-08-13 15:00:37 +10:00
ripplebizandGitHub abd3546d75 Merge pull request #3189 from oltaco/nrf52-unused-pin-sweep 
Fix unused pin definitions on some NRF52 boards
 2026-08-13 13:48:59 +10:00
taco 7cd1d207af Fix LilyGo T-Echo Lite SPI pins 2026-08-13 00:53:58 +10:00
taco c2a4ef082f Fix Heltec MeshPocket SPI pins 2026-08-13 00:15:34 +10:00
taco 3ea541f1f2 Fix Heltec T1 pin definitions 
SPI pins that are set to -1 cause OOB reads on NRF52. The unused Serial2 pin definitions were removed to avoid potential issues with the Uart framework.
 2026-08-13 00:12:37 +10:00
ripplebizandGitHub e9edfc8e1a Merge pull request #3188 from oltaco/heltec-t096-pin-fix 
Fix Heltec T096 Tx issue
 2026-08-12 23:00:31 +10:00
taco 49d9f9a839 Heltec T096: fix PIN_SPI1_MISO 
Setting SPI pins to values that are OOB of the g_ADigitalPinMap[] array causes OOB reads. This variant.h has pin 0 as 0xFF which passes through as NRFX_SPIM_PIN_NOT_USED.
 2026-08-12 22:31:57 +10:00
taco f43e1cde89 Revert "t096 compiler layout workaround" 
This reverts commit 9c60f9696e.
 2026-08-12 22:28:36 +10:00
taco 264d778168 Revert "T096 PA_CTX pin direction workaround" 
This reverts commit 82de18fb0e.
 2026-08-12 22:28:05 +10:00
ripplebizandGitHub 956094b271 Merge pull request #3185 from oltaco/fix-techo-card-txco-voltage 
Set T-Echo Card TCXO voltage to 3.0
 2026-08-12 18:13:44 +10:00
ripplebizandGitHub a4ab7f0e59 Merge pull request #3137 from agessaman/feat/station-g3-fem-prefs 
Station G3: Expose, persist, and apply FEM gain preferences
 2026-08-12 16:11:23 +10:00
taco 9d6dcc673e set T-Echo Card TCXO voltage to 3.0 
as per https://github.com/meshcore-dev/MeshCore/pull/3140 and https://github.com/Xinyuan-LilyGO/T-Echo-Lite/issues/14
 2026-08-12 16:08:05 +10:00
ripplebizandGitHub 1cb308b694 Merge pull request #3182 from oltaco/t096-tx-workaround 
Workaround for Heltec T096 transmit issue
 2026-08-12 14:49:32 +10:00
taco 82de18fb0e T096 PA_CTX pin direction workaround 2026-08-12 14:07:31 +10:00
taco 9c60f9696e t096 compiler layout workaround 
see https://github.com/meshcore-dev/MeshCore/issues/3151
 2026-08-12 14:04:50 +10:00
ripplebizandGitHub e027263d1e Merge pull request #3154 from fdlamotte/nrf52_hwcrypto_init 
nrf52: call nRFCrypto.begin()/end() only once
 2026-08-12 12:14:21 +10:00
Huw DuddyandGitHub 34ad059afb Merge pull request #3170 from recrof/promicro-pin-tidy-up 
[promicro] make pinmap more tidy, move the LoRa pins to variant.h
 2026-08-11 18:43:20 +10:00
Rastislav Vysoky 5cce5cfe97 removed misleading 'GPIO' from pin numbers 2026-08-11 10:37:20 +02:00
ripplebizandGitHub fbef2ff0dc Merge pull request #3164 from weebl2000/fix-tbeam-s3-display 
Fix display issues on T-beam Supreme S3
 2026-08-11 14:39:39 +10:00
agessaman e2aa7b98f9 feat(companion_radio): add external FEM gain preferences for RX and TX for companions 
Introduced consistent preferences for external LoRa FEM RX and TX gain settings in NodePrefs. Updated companion MyMesh to apply these settings during initialization and transmission. Added unit tests to verify the round-trip serialization of these new preferences.
 2026-08-10 11:59:26 -07:00
Rastislav Vysoky a82dc1b9da make promicro pinmap more tidy, move the LoRa pins to variant.h 2026-08-10 20:13:59 +02:00
Liam CottleandGitHub 9d8894e166 Merge pull request #3166 from recrof/debug-noise-floor-flag 
move RadioLibWrapper noise_floor level message under special debug flag
 2026-08-11 03:07:31 +12:00
Rastislav Vysoky 3138ad99ba move RadioLibWrapper noise_floor level message under special debug flag 2026-08-10 16:56:56 +02:00
Wessel Nieboer 32bd6d48d6 Fix T-beam Supreme S3 display 2026-08-10 13:39:16 +02:00
Huw DuddyandGitHub f6c25e6a25 Merge pull request #3158 from mepholic/bug/fix-rxgain-setting-post-agc-reset 
Fix RX Boosted Gain setting after AGC reset is triggered
 2026-08-10 17:31:38 +10:00
ripplebizandGitHub 9941669fd5 Merge pull request #3142 from oltaco/buildfix-userbtn 
Build fix for R1 Neo and Minewsemi repeater
 2026-08-10 13:30:24 +10:00
ripplebizandGitHub 0d60de6fa6 Merge pull request #3146 from oltaco/lr2021-preamble-and-irq-timeout 
LR2021: add PREAMBLE_DETECTED bit and IRQ timeout logic
 2026-08-10 13:29:12 +10:00
Dan Theisen 6f491f3033 RX Boosted Gain was set back to the compiled in value rather than the current/flash value set by the user when the ACG reset is triggered. This commit fixes this. 2026-08-09 18:11:35 -07:00
Florent ecb8c94560 nrf52: call nRFCrypto.begin()/end() only once 2026-08-09 14:46:23 -04:00
Huw DuddyandGitHub a1c50e15dd Merge pull request #3148 from recrof/add-missing-kiss-radio 
add missing kiss radio roles, add kiss radio build to build.sh
 2026-08-09 22:22:08 +10:00
Rastislav Vysoky c2d57f08c8 add missing kiss radio roles, add kiss radio build to build.sh 2026-08-09 14:17:18 +02:00
Huw DuddyandGitHub f310afb5e5 Merge pull request #3140 from entr0p1/fix/techo-lite-pins 
Lilygo T-Echo Lite Pin Fixes
 2026-08-09 22:06:21 +10:00
taco ce62c8b5d7 LR2021: add PREAMBLE_DETECTED bit and IRQ timeout logic 2026-08-09 21:41:22 +10:00
taco 39934d6999 minewsemi: build fix and platformio.ini tidy up 
fixes minewsemi repeater failing build due to user_btn missing.
 2026-08-09 18:33:27 +10:00
taco e8bbcd4580 R1 neo: remove stray lib_deps entry 2026-08-09 16:51:45 +10:00
taco b75a548d7f build fix for R1 Neo repeater 
added missing declarations for user_btn and NullDisplayDriver
 2026-08-09 16:50:44 +10:00
Scott Powell 727fc0512c Merge branch 'dev' 
# Conflicts:
#	docs/payloads.md
 2026-08-09 15:16:48 +10:00
Scott Powell 93b2db63de * version 1.17.0 2026-08-09 15:14:46 +10:00
entr0p1 5732b2edd8 Lilygo T-Echo Lite Pin Fixes 
- Aligned to Lilygo's updated schematic and pin map as per https://github.com/Xinyuan-LilyGO/T-Echo-Lite/issues/14
 2026-08-09 14:09:35 +10:00
ripplebizandGitHub 48df179e36 Merge pull request #3139 from oltaco/x1-flash 
Add QSPIFlash support for Seeed MeshTracker X1
 2026-08-09 13:52:56 +10:00
Huw DuddyandGitHub 58ebff82c0 Merge pull request #3125 from Hacuchino-hash/fix-x1-charge-status 
Fix X1 charge status LED always showing charged
 2026-08-09 12:54:29 +10:00