mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-11-21 22:47:05 +00:00
Merge pull request #3664 from Martin-hub1/dev
Add DFRobot LoRaWAN ESP32-S3 Companion BLE firmware
This commit is contained in:
7 files changed
+210
-2
No files matched your search
@@ -0,0 +1,39 @@
|
||||
{
|
||||
"build": {
|
||||
"arduino": {
|
||||
"ldscript": "esp32s3_out.ld"
|
||||
},
|
||||
"core": "esp32",
|
||||
"extra_flags": [
|
||||
"-D ARDUINO_USB_CDC_ON_BOOT=0",
|
||||
"-D ARDUINO_USB_MSC_ON_BOOT=0",
|
||||
"-D ARDUINO_USB_DFU_ON_BOOT=0",
|
||||
"-D ARDUINO_USB_MODE=0",
|
||||
"-D ARDUINO_RUNNING_CORE=1",
|
||||
"-D ARDUINO_EVENT_RUNNING_CORE=1"
|
||||
],
|
||||
"f_cpu": "240000000L",
|
||||
"f_flash": "80000000L",
|
||||
"flash_mode": "qio",
|
||||
"hwids": [["0x303A", "0x1001"]],
|
||||
"mcu": "esp32s3",
|
||||
"variant": "esp32s3"
|
||||
},
|
||||
"connectivity": ["wifi", "bluetooth", "lora"],
|
||||
"debug": {
|
||||
"default_tool": "esp-builtin",
|
||||
"onboard_tools": ["esp-builtin"],
|
||||
"openocd_target": "esp32s3.cfg"
|
||||
},
|
||||
"frameworks": ["arduino", "espidf"],
|
||||
"name": "DFRobot LoRaWAN ESP32-S3 (4 MB Flash, No PSRAM)",
|
||||
"upload": {
|
||||
"flash_size": "4MB",
|
||||
"maximum_ram_size": 524288,
|
||||
"maximum_size": 4194304,
|
||||
"require_upload_port": true,
|
||||
"speed": 921600
|
||||
},
|
||||
"url": "https://www.dfrobot.com",
|
||||
"vendor": "DFRobot"
|
||||
}
|
||||
@@ -102,7 +102,8 @@
|
||||
static TFT_eSPI lcd = TFT_eSPI(160, 80);
|
||||
static uint32_t curr_color;
|
||||
|
||||
#if defined(HELTEC_LORA_V3) || defined(HELTEC_TRACKER_V2)
|
||||
#if defined(HELTEC_LORA_V3) || defined(HELTEC_TRACKER_V2) || defined(DFROBOT_LORAWAN_ESP32S3)
|
||||
// ESP32-S3: HSPI is SPI3. The SX1262 uses FSPI (SPI2) so the two buses do not share a controller.
|
||||
static SPIClass tft_spi(HSPI);
|
||||
#define _spi (&tft_spi)
|
||||
#else
|
||||
@@ -490,7 +491,7 @@ void ST7735Display::_resetAndInit() {
|
||||
|
||||
// run init commands
|
||||
displayInit(Rcmd1);
|
||||
#if defined(HELTEC_TRACKER_V2) || defined(HELTEC_T096)
|
||||
#if defined(HELTEC_TRACKER_V2) || defined(HELTEC_T096) || defined(DFROBOT_LORAWAN_ESP32S3)
|
||||
displayInit(Rcmd2green160x80);
|
||||
//uint8_t madctl = ST77XX_MADCTL_MY | ST77XX_MADCTL_MV |ST7735_MADCTL_BGR;//Adjust color to BGR
|
||||
//display.sendCommand(ST77XX_MADCTL, &madctl, 1);
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
#include "DFRobotLoRaBoard.h"
|
||||
|
||||
void DFRobotLoRaBoard::begin() {
|
||||
// SX1262 module power. Held high for the whole boot; Companion does not
|
||||
// drop into deep sleep, so the pin does not need an RTC hold.
|
||||
pinMode(LORA_POWER_EN, OUTPUT);
|
||||
digitalWrite(LORA_POWER_EN, HIGH);
|
||||
delay(10);
|
||||
|
||||
periph_power.begin();
|
||||
|
||||
pinMode(PIN_LED, OUTPUT);
|
||||
digitalWrite(PIN_LED, HIGH);
|
||||
|
||||
ESP32Board::begin();
|
||||
}
|
||||
|
||||
const char* DFRobotLoRaBoard::getManufacturerName() const {
|
||||
return "DFRobot LoRaWAN ESP32-S3";
|
||||
}
|
||||
@@ -0,0 +1,15 @@
|
||||
#pragma once
|
||||
|
||||
#include <Arduino.h>
|
||||
#include <helpers/RefCountedDigitalPin.h>
|
||||
#include <helpers/ESP32Board.h>
|
||||
|
||||
class DFRobotLoRaBoard : public ESP32Board {
|
||||
public:
|
||||
RefCountedDigitalPin periph_power;
|
||||
|
||||
DFRobotLoRaBoard() : periph_power(PIN_VEXT_EN, PIN_VEXT_EN_ACTIVE) { }
|
||||
|
||||
void begin();
|
||||
const char* getManufacturerName() const override;
|
||||
};
|
||||
@@ -0,0 +1,73 @@
|
||||
; DFRobot LoRaWAN ESP32-S3 (DFR1195)
|
||||
; ESP32-S3-WROOM-1-N4 (4 MB flash, no PSRAM), SX1262, SPI ST7735S 80x160.
|
||||
; Pin map follows variants/esp32s3/DFRobot_LoRaWAN_ESP32-S3 in the Meshtastic tree.
|
||||
; LoRa is on FSPI. The display is on HSPI (SPI3), matching ST7735_SPI_HOST.
|
||||
[DFRobot_LoRaWAN_ESP32S3]
|
||||
extends = esp32_base
|
||||
board = dfrobot_lorawan_esp32s3
|
||||
; 4 MB module: app slots are 1.9 MB. The default 4 MB table only leaves 1.25 MB.
|
||||
board_build.partitions = min_spiffs.csv
|
||||
build_flags =
|
||||
${esp32_base.build_flags}
|
||||
-I variants/dfrobot_lorawan_esp32s3
|
||||
-D DFROBOT_LORAWAN_ESP32S3
|
||||
-D ESP32_CPU_FREQ=80
|
||||
-D RADIO_CLASS=CustomSX1262
|
||||
-D WRAPPER_CLASS=CustomSX1262Wrapper
|
||||
-D LORA_TX_POWER=22
|
||||
-D P_LORA_NSS=10
|
||||
-D P_LORA_DIO_1=4
|
||||
-D P_LORA_RESET=41
|
||||
-D P_LORA_BUSY=40
|
||||
-D P_LORA_SCLK=7
|
||||
-D P_LORA_MISO=5
|
||||
-D P_LORA_MOSI=6
|
||||
-D LORA_POWER_EN=42
|
||||
-D SX126X_DIO2_AS_RF_SWITCH=true
|
||||
-D SX126X_DIO3_TCXO_VOLTAGE=3.3
|
||||
-D SX126X_CURRENT_LIMIT=140
|
||||
-D SX126X_RX_BOOSTED_GAIN=1
|
||||
-D PIN_USER_BTN=18
|
||||
-D PIN_LED=21
|
||||
-D PIN_VEXT_EN=48
|
||||
-D PIN_VEXT_EN_ACTIVE=LOW
|
||||
-D PIN_BOARD_SDA=8
|
||||
-D PIN_BOARD_SCL=9
|
||||
-D PIN_TFT_CS=17
|
||||
-D PIN_TFT_DC=14
|
||||
-D PIN_TFT_RST=15
|
||||
-D PIN_TFT_SDA=11
|
||||
-D PIN_TFT_SCL=12
|
||||
-D PIN_TFT_LEDA_CTL=16
|
||||
-D PIN_TFT_LEDA_CTL_ACTIVE=HIGH
|
||||
build_src_filter = ${esp32_base.build_src_filter}
|
||||
+<../variants/dfrobot_lorawan_esp32s3>
|
||||
lib_deps =
|
||||
${esp32_base.lib_deps}
|
||||
bodmer/TFT_eSPI @ ^2.4.31
|
||||
|
||||
; Landscape UI on the 80x160 panel. Use 3 if the picture is upside down.
|
||||
[env:DFRobot_LoRaWAN_ESP32S3_companion_radio_ble]
|
||||
extends = DFRobot_LoRaWAN_ESP32S3
|
||||
build_flags =
|
||||
${DFRobot_LoRaWAN_ESP32S3.build_flags}
|
||||
-I src/helpers/ui
|
||||
-I examples/companion_radio/ui-new
|
||||
-D DISPLAY_ROTATION=3
|
||||
-D DISPLAY_CLASS=ST7735Display
|
||||
-D MAX_CONTACTS=350
|
||||
-D MAX_GROUP_CHANNELS=40
|
||||
-D BLE_PIN_CODE=123456
|
||||
-D OFFLINE_QUEUE_SIZE=256
|
||||
; -D BLE_DEBUG_LOGGING=1
|
||||
; -D MESH_PACKET_LOGGING=1
|
||||
; -D MESH_DEBUG=1
|
||||
build_src_filter = ${DFRobot_LoRaWAN_ESP32S3.build_src_filter}
|
||||
+<helpers/esp32/SerialBLEInterface.cpp>
|
||||
+<helpers/ui/MomentaryButton.cpp>
|
||||
+<helpers/ui/ST7735Display.cpp>
|
||||
+<../examples/companion_radio/*.cpp>
|
||||
+<../examples/companion_radio/ui-new/*.cpp>
|
||||
lib_deps =
|
||||
${DFRobot_LoRaWAN_ESP32S3.lib_deps}
|
||||
densaugeo/base64 @ ~1.4.0
|
||||
@@ -0,0 +1,34 @@
|
||||
#include <Arduino.h>
|
||||
#include <SPI.h>
|
||||
#include "target.h"
|
||||
|
||||
DFRobotLoRaBoard board;
|
||||
|
||||
// FSPI is SPI2. The ST7735 driver takes HSPI (SPI3); the default SPIClass
|
||||
// constructor on ESP32-S3 is HSPI and would collide with the display.
|
||||
static SPIClass spi(FSPI);
|
||||
RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, spi);
|
||||
|
||||
WRAPPER_CLASS radio_driver(radio, board);
|
||||
|
||||
ESP32RTCClock fallback_clock;
|
||||
AutoDiscoverRTCClock rtc_clock(fallback_clock);
|
||||
SensorManager sensors;
|
||||
|
||||
#ifdef DISPLAY_CLASS
|
||||
DISPLAY_CLASS display(&board.periph_power);
|
||||
// Active-low button, internal pull-up.
|
||||
MomentaryButton user_btn(PIN_USER_BTN, 1000, true, true);
|
||||
#endif
|
||||
|
||||
bool radio_init() {
|
||||
fallback_clock.begin();
|
||||
rtc_clock.begin(Wire);
|
||||
|
||||
return radio.std_init(&spi);
|
||||
}
|
||||
|
||||
mesh::LocalIdentity radio_new_identity() {
|
||||
RadioNoiseListener rng(radio);
|
||||
return mesh::LocalIdentity(&rng); // create new random identity
|
||||
}
|
||||
@@ -0,0 +1,26 @@
|
||||
#pragma once
|
||||
|
||||
#define RADIOLIB_STATIC_ONLY 1
|
||||
#include <RadioLib.h>
|
||||
#include <helpers/radiolib/RadioLibWrappers.h>
|
||||
#include <DFRobotLoRaBoard.h>
|
||||
#include <helpers/radiolib/CustomSX1262Wrapper.h>
|
||||
#include <helpers/AutoDiscoverRTCClock.h>
|
||||
#include <helpers/SensorManager.h>
|
||||
#ifdef DISPLAY_CLASS
|
||||
#include <helpers/ui/ST7735Display.h>
|
||||
#include <helpers/ui/MomentaryButton.h>
|
||||
#endif
|
||||
|
||||
extern DFRobotLoRaBoard board;
|
||||
extern WRAPPER_CLASS radio_driver;
|
||||
extern AutoDiscoverRTCClock rtc_clock;
|
||||
extern SensorManager sensors;
|
||||
|
||||
#ifdef DISPLAY_CLASS
|
||||
extern DISPLAY_CLASS display;
|
||||
extern MomentaryButton user_btn;
|
||||
#endif
|
||||
|
||||
bool radio_init();
|
||||
mesh::LocalIdentity radio_new_identity();
|
||||
Reference in new issue
Block a user