The remote-CLI reply buffers in onPeerDataRecv() (repeater, room server,
sensor) and BaseChatMesh were sized temp[166] for a 5-byte datagram
header plus 161 bytes of reply. But MyMesh::handleCommand() first
reflects a 3-byte correlation prefix (e.g. 'aa|') into the reply, after
which CommonCLI commands may write up to 160 chars + NUL into the
remaining 158 bytes -- overflowing the buffer by 2 bytes (e.g. a full
'regions' listing via exportTo(reply, 160)).
Triggering this remotely crashes the node (observed as an unresponsive
repeater after a prefixed 'regions' query); the 2 out-of-bounds bytes
are a printable region-name character and a NUL.
Size the buffers for the full worst case instead:
5 header + 3 prefix + 160 reply + 1 NUL = 169.
Verified with a host ASan harness reproducing the exact layout:
prefixed 'regions' with a 25-region listing overflowed temp[166]
(BufStream::write, RegionMap.cpp) and now passes clean with temp[169];
unprefixed (serial) path unaffected.
The room server gated its filesystem paths on NRF52_PLATFORM only, so an
STM32 build fell through to the ESP32 branch and failed to compile:
MyMesh.cpp:147: no matching function for call to
'Adafruit_LittleFS::open(const char*&, const char [2], bool)'
main.cpp:69: 'store' was not declared in this scope
STM32 uses the same InternalFS / Adafruit_LittleFS API as nRF52, including
append semantics (FILE_O_WRITE opens LFS_O_RDWR|LFS_O_CREAT and then seeks
to the end), so the nRF52 branch is already correct for it. Add
STM32_PLATFORM alongside NRF52_PLATFORM in the four remaining gates;
saveIdentity() already did this.
This unblocks the room_server example on the existing STM32WL boards
(wio-e5-mini, wio-e5-dev, rak3x72, tiny_relay) as well as new ones.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The serial command buffers must stay NUL-terminated within their
bounds: if they ever aren't, strlen() can return >= sizeof(command)
and the read loop would index past the buffer. Additionally, a full
buffer now becomes a completed line (end-of-line marker placed
inside the buffer, NUL terminator kept) instead of overwriting the
terminator and silently corrupting the buffer for the next pass.
Applies to the serial CLI readers of the repeater, room server,
sensor and secure chat examples, and to the CLI rescue reader of
the companion example.
The room server never supported RX boosted gain, while the repeater
does. Three consequences on SX1262/SX1268 boards:
- boosted gain was never applied to the radio at boot, so a room server
ran in power-saving RX mode while an identical repeater ran boosted -
a real receive-sensitivity difference with nothing pointing at it
- _prefs.rx_boosted_gain was never initialised (the prefs are memset to
0 before defaults are set), so it defaulted to off
- 'set radio.rxgain on' replied "Error: unsupported" but CommonCLI had
already written the value to prefs and saved them, so a stale setting
survived reboot and was never applied
Mirror the repeater's implementation: initialise the pref default under
the same USE_SX1262/USE_SX1268 and SX126X_RX_BOOSTED_GAIN guards, apply
it during radio init, and override setRxBoostedGain() so the CLI reports
success and takes effect.
Built Heltec_v3_room_server (SX1262) and LilyGo_T3S3_sx1276_room_server
(guards compile out cleanly).
The `recv_pkt_region` is set when processing a flood packet in `filterRecvFloodPacket`
but direct/non-flood packets would never pass through that function, so the pointer was
not cleared for them.
`sendFloodReply` would then later use it blindly, which meant that the response would
either inherit the region from the last flood packet, or refer to a non-initialised pointer
if no region floods had been received yet.
Before this commit, there was no way to set a different max hop count
for unscoped messages.
Now with this change, by defaul it tracks the flood.max setting, until
a user provides a flood.max.unscoped value, which tax precidence for
packets if ROUTE_TYPE_FLOOD is true.
Framework for upcoming variant-specific PRs that add LED feedback during boot. The hook gives users visual cues that the device is busy and
shouldn't be interacted with until startup completes.