mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-11-22 05:27:02 +00:00
A RAK4631 core paired with a RAK13302 leaves the core's own SX1262 powered but never initialized, idling in STDBY_RC for the life of the board. Firmware cannot cut its supply -- P1.05 is the RF switch rail, not the radio's -- so bring it up on its own pins just long enough to issue a cold sleep, before std_init() repins SPI onto the RAK13302. Gated behind RAK4631_ONBOARD_SX1262_SLEEP and exposed through seven RAK_4631_13302_* envs, so RAK_3401_* artifacts are unchanged. The sleep is issued regardless of what begin() returns: Module::init() runs first, so SPI stays usable even if TCXO calibration fails. NSS is then held high, since the SX1262 wakes on an NSS falling edge. Verified on RAK19007 + RAK4631 + RAK13302: begin=0 sleep=0, RAK13302 init clean (device_errors=0x0000), TX and RX both confirmed. The current saving itself is derived from the datasheet (600 uA STDBY_RC -> 160 nA cold sleep) and is not measured.
78 lines
2.5 KiB
C++
78 lines
2.5 KiB
C++
#include <Arduino.h>
|
|
#include "target.h"
|
|
#include <helpers/ArduinoHelpers.h>
|
|
|
|
RAK3401Board board;
|
|
|
|
#ifndef PIN_USER_BTN
|
|
#define PIN_USER_BTN (-1)
|
|
#endif
|
|
|
|
#ifdef DISPLAY_CLASS
|
|
DISPLAY_CLASS display;
|
|
MomentaryButton user_btn(PIN_USER_BTN, 1000, true, true);
|
|
|
|
#if defined(PIN_USER_BTN_ANA)
|
|
MomentaryButton analog_btn(PIN_USER_BTN_ANA, 1000, 20);
|
|
#endif
|
|
#endif
|
|
|
|
RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, SPI);
|
|
|
|
WRAPPER_CLASS radio_driver(radio, board);
|
|
|
|
VolatileRTCClock fallback_clock;
|
|
AutoDiscoverRTCClock rtc_clock(fallback_clock);
|
|
|
|
#if ENV_INCLUDE_GPS
|
|
#include <helpers/sensors/MicroNMEALocationProvider.h>
|
|
MicroNMEALocationProvider nmea = MicroNMEALocationProvider(Serial1, &rtc_clock);
|
|
EnvironmentSensorManager sensors = EnvironmentSensorManager(nmea);
|
|
#else
|
|
EnvironmentSensorManager sensors;
|
|
#endif
|
|
|
|
#ifdef RAK4631_ONBOARD_SX1262_SLEEP
|
|
// With a RAK13302 fitted the RAK4631's own SX1262 never gets initialized, so it
|
|
// sits in STDBY_RC drawing standby current for the life of the board. Firmware
|
|
// cannot cut its supply -- P1.05 is the RF switch rail, not the radio's -- so
|
|
// bring it up on its own pins just long enough to put it into cold sleep.
|
|
static void sleep_onboard_radio() {
|
|
pinMode(ONBOARD_LORA_ANT_SW, OUTPUT);
|
|
digitalWrite(ONBOARD_LORA_ANT_SW, LOW); // nothing downstream needs the RF switch
|
|
|
|
SPI.setPins(ONBOARD_LORA_MISO, ONBOARD_LORA_SCLK, ONBOARD_LORA_MOSI);
|
|
SPI.begin();
|
|
|
|
Module mod(ONBOARD_LORA_NSS, ONBOARD_LORA_DIO_1, ONBOARD_LORA_RESET, ONBOARD_LORA_BUSY, SPI);
|
|
SX1262 onboard(&mod);
|
|
|
|
// begin() resets the chip and leaves it in standby. A TCXO calibration failure
|
|
// still leaves SPI usable, so issue the sleep regardless of what it returns.
|
|
int status = onboard.begin(434.0f, 125.0f, 9, 7, RADIOLIB_SX126X_SYNC_WORD_PRIVATE,
|
|
0, 8, ONBOARD_LORA_TCXO_VOLTAGE, false);
|
|
int slept = onboard.sleep(false); // cold sleep: config discarded, RTC off
|
|
MESH_DEBUG_PRINTLN("onboard SX1262: begin=%d sleep=%d", status, slept);
|
|
|
|
SPI.end(); // release SPIM3 so std_init() can repin it onto the RAK13302
|
|
|
|
// The SX1262 wakes on an NSS falling edge, so keep NSS driven high from here on.
|
|
digitalWrite(ONBOARD_LORA_NSS, HIGH);
|
|
pinMode(ONBOARD_LORA_NSS, OUTPUT);
|
|
}
|
|
#endif
|
|
|
|
bool radio_init() {
|
|
rtc_clock.begin(Wire);
|
|
#ifdef RAK4631_ONBOARD_SX1262_SLEEP
|
|
sleep_onboard_radio();
|
|
#endif
|
|
return radio.std_init(&SPI);
|
|
}
|
|
|
|
mesh::LocalIdentity radio_new_identity() {
|
|
RadioNoiseListener rng(radio);
|
|
return mesh::LocalIdentity(&rng); // create new random identity
|
|
}
|
|
|