mirror of
https://github.com/meshcore-dev/MeshCore.git
synced 2026-11-21 22:47:05 +00:00
On a RAK19007 the RAK12501's supply is 3V3_S, switched by WB_IO2, so gps off, periodic mode and shutdown left it powered. Pass WB_IO2 to the NMEA driver as peripheralPower under GPS_RAIL_POWER_CONTROL, set by the new RAK_4631_repeater_gps_power env. It is opt-in because the rail feeds every slot module, and refused with ETHERNET_ENABLED (RAK13800). The RAK12500 (I2C) driver keeps switching its own power pin, so this only applies on the NMEA path. RefCountedDigitalPin now sets OUTPUT on claim and release: WB_IO2 left as an input (as probeRak12500() leaves it after a failed probe) keeps 3V3_S in its last state, so writing the latch alone did not cut it. Measured with a KM003C, battery and panel out: gps off 40.5 -> 12.4 mA, shutdown 29.7 -> 1.30 mA.
54 lines
1.4 KiB
C++
54 lines
1.4 KiB
C++
#include <Arduino.h>
|
|
#include "target.h"
|
|
#include <helpers/ArduinoHelpers.h>
|
|
|
|
RAK4631Board board;
|
|
|
|
#ifndef PIN_USER_BTN
|
|
#define PIN_USER_BTN (-1)
|
|
#endif
|
|
|
|
#ifdef DISPLAY_CLASS
|
|
DISPLAY_CLASS display;
|
|
MomentaryButton user_btn(PIN_USER_BTN, 1000, true, true);
|
|
|
|
#if defined(PIN_USER_BTN_ANA)
|
|
MomentaryButton analog_btn(PIN_USER_BTN_ANA, 1000, 20);
|
|
#endif
|
|
#endif
|
|
|
|
RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, SPI);
|
|
|
|
WRAPPER_CLASS radio_driver(radio, board);
|
|
|
|
VolatileRTCClock fallback_clock;
|
|
AutoDiscoverRTCClock rtc_clock(fallback_clock);
|
|
|
|
#if ENV_INCLUDE_GPS
|
|
#include <helpers/sensors/RakLocationProvider.h>
|
|
RakI2cGpsDriver gps_driver;
|
|
#ifdef GPS_RAIL_POWER_CONTROL
|
|
#ifdef ETHERNET_ENABLED
|
|
#error "GPS_RAIL_POWER_CONTROL would cut the RAK13800's power, which also comes from WB_IO2"
|
|
#endif
|
|
// WB_IO2 switches 3V3_S, which powers the serial GPS and every other slot module.
|
|
RefCountedDigitalPin gps_rail(WB_IO2);
|
|
RakLocationProvider location(gps_driver, &rtc_clock, Serial1, &gps_rail);
|
|
#else
|
|
RakLocationProvider location(gps_driver, &rtc_clock);
|
|
#endif
|
|
EnvironmentSensorManager sensors(location);
|
|
#else
|
|
EnvironmentSensorManager sensors;
|
|
#endif
|
|
|
|
bool radio_init() {
|
|
rtc_clock.begin(Wire);
|
|
return radio.std_init(&SPI);
|
|
}
|
|
|
|
mesh::LocalIdentity radio_new_identity() {
|
|
RadioNoiseListener rng(radio);
|
|
return mesh::LocalIdentity(&rng); // create new random identity
|
|
}
|