* Perform unsubscribe in parallel to avoid blocking
When unsubscribing from tracks, we flush a blank frame in order to prepare
the transceivers for re-use. This process is blocking for ~200ms. If
the unsubscribes are performed serially, it would prevent other subscribe
operation from continuing.
This PR parallelizes that operation, and ensures subsequent subscribe
operations could reuse the existing transceivers.
* also perform in parallel when uptrack close
* fix a few log fields
* Avoid reconnect loop for unsupported downtrack
If the client subscribes to a track which codec is unsupported by the
client, sfu will trigger negotiation failed and issue a full reconnect
after received client answer. If the client try to subscribe that track
then it will got full reconnect again. That will cause a infinite
reconnect loop until the client don't subscribe that track. This PR
will unsubscribe the error track for the client and send a
SubscriptionResponse that contain the reason to indicates the track's
codec is not supported to avoid the reconnect loop.
Because we aren't able to get CPU count/load info on Windows, they are
stubbed out to return placeholders. This restores compatibility to run
on Windows.
* Split probe controller from StreamAllocator.
With TWCC, there is a need to check for probe status
in a separate goroutine. So, probe specific stuff need
locking. Split out the probe controller to make that cleaner.
* remove defer
* Return max spatial layer from selectors.
With differing requirements of SVC and allowing overshoot in Simulcast,
selectors are best placed to indicate what is the max spatial layer when
they indicate a switch to max spatial layer.
* fix test
* prevent race
It is possible that publisher paces the media.
So, RTCP sender report from publisher could be ahead of
what is being fowarded by a good amount (have seen up to 2 seconds
ahead). Using the forwarded time stamp for RTCP sender report
in the down stream leads to jumps back and forth in the down track
RTCP sender report.
So, look at the publisher's RTCP sender report to check for it being
ahead and use the publisher rate as a guide.
Actually, was not filtering the not last sender report error before.
Previous PR did that. This PR restores the old no last sender report
filter. Both are filterable errors.
* Fix unwrap
An out-or-order packet wrapping back after a wrap around had already happened
was not using proper cycle ounter to calculate unerapped value.
* update mediatransportutil
Active TCP was added in pion/ice v2.3.4. This is causing a couple of issues for us.
Active TCP does not make sense for an SFU. Clients are expected to be behind NAT and we should not be dialing them. Instead, LiveKit exposes a TCP port so clients could dial in
Active TCP is causing all iOS clients to become disconnected immediately. This is impacting all version of libwebrtc-based iOS clients (tested from M104 to M111)
* send min/median connection score along with avg
* guard against divide by zero for avg score calculation
* update median calculation
Signed-off-by: shishir gowda <shishir@livekit.io>
1. Completely removing RTT and jitter from score calculation.
Need to do more work there.
a. Jitter is slow moving (RFC 3550 formula is designed that way).
But, we still get high values at times. Ideally, that should
penalise the score, but due to jitter buffer, effect may not be
too bad.
b. Need to smooth RTT. It is based on receiver report and if one
sample causes a high number, score could be penalised
(this was being used in down track direction only). One option
is to smooth it like the jitter formula above and try using it.
But, for now, disabling that also.
2. When receiving lesser number of packets (for example DTX), reduce the
weight of packet loss with a quadratic relationship to packet loss
ratio. Previously using a square root and it was potentially
weighting it too high. For example, if only 5 packets were received
due to DTX instead of 50, we were still giving 30% weight
(sqrt(0.1)). Now, it gets 1% weight. So, if one of those 5 packets
were lost (20% packet loss ratio), it still does not get much weight
as the number of packets is low.,
3. Slightly slower decrease in score (in EWMA)
4. When using RED, increase packet loss weight thresholds to be able to
take more loss before penalizing score.
Two things
- Somehow the publisher RTCP sender report time stamp goes back some
times. Log it differently. Also, use signed type for logging so
that negative is easy to see.
- On down track, because of silence frame injection on mute, the RTCP
sender report time stamp might be ahead of timestamp we will use
on unmute. If so, ensure that next timestamp is also not before
what was sent in RTCP sender report.
* Make signal close async.
Left notes about async close in code.
Also reducing retry config timeout
- Timeout to 7.5 seconds (making it 1/4th of current config)
- max retry to 4 seconds
- so, it can do 4 tries now in 7.5 seconds (with retries ending at 0.5
seconds, 1.5 seconds, 3.5 seconds, 7.5 seconds). The change of max to
4 seconds is not really needed, but it lined up with 7.5. So, made the
change.
* update comments a bit
The PID controller seems to be working well. But, it is unclear where
it can be applied as some of the data shows significant jumps
(either caused by BT devices or possibly noise cancellation/cpu
constraint) and although PID controller is slowly pulling things
to expected sample rate, it could be a bit slow.
Unfortunately, cannot munge too much in a middle box.
However leaving the controller in there as it is doing its job
for cases where things slip slowly.
Changing things to log significant jumps (more than 200 ms away
from expected) at Infow level.
Also, recording drift and sample rate in RTP stats proto and string
representation.
