mirror of
https://github.com/RfidResearchGroup/proxmark3.git
synced 2026-10-02 10:38:20 +00:00
iceman1001
6d67465d7d
The FPGA trace loop was the last OLD reply on the device outside the two the bootrom also serves. It stayed OLD because the DMA double-buffer was sized to the frame payload and an NG header did not obviously fit in front of it. DMA straight into chunk->data of a download_chunk_t instead, so a filled buffer is already a complete NG payload and needs no copy. Chunking now follows DOWNLOAD_CHUNK_MAX and scales with PM3_CMD_DATA_SIZE. The terminator carries download_done_t like the other bulk downloads. No client change needed, dl_it already had the NG branch. Two fixes fall out of it: FPGA_TRACE_SIZE is 3072, an exact multiple of 512 but not of DOWNLOAD_CHUNK_MAX. Each transfer is now armed for exactly the bytes still expected - arming a full chunk for the short last one would spin in FPGA_SSC_DMA_RX_Done() forever. This also drops the stray extra DMA the old loop left armed. get_tosend() moved after FpgaDownloadAndGo(). The loader calls BigBuf_free(), which nulls s_toSend.buf, then reuses that same region for its decompression ring buffer - the old code captured the pointer before the free and only worked because the loader was done with it in time. 3072 bytes goes from 6 OLD frames to 7 NG frames at PM3_CMD_DATA_SIZE 512, and would be 5 at 688.
597 lines
23 KiB
Markdown
597 lines
23 KiB
Markdown
# New frame format documentation
|
|
<a id="Top"></a>
|
|
|
|
This document is primarily intended for developers only.
|
|
|
|
A major change is the support of variable length frames between host and Proxmark3.
|
|
This is a step especially important for usage over FPC/USART/BT.
|
|
|
|
|
|
# Table of Contents
|
|
- [New frame format documentation](#new-frame-format-documentation)
|
|
- [Table of Contents](#table-of-contents)
|
|
- [Old format](#old-format)
|
|
- [New format](#new-format)
|
|
- [Transition](#transition)
|
|
- [New format API](#new-format-api)
|
|
- [On the client, for sending frames](#on-the-client-for-sending-frames)
|
|
- [On the Proxmark3, for receiving frames](#on-the-proxmark3-for-receiving-frames)
|
|
- [On the Proxmark3, for sending frames](#on-the-proxmark3-for-sending-frames)
|
|
- [On the client, for receiving frames](#on-the-client-for-receiving-frames)
|
|
- [API transition](#api-transition)
|
|
- [Practical notes from converting the tree](#practical-notes-from-converting-the-tree)
|
|
- [Bulk downloads](#bulk-downloads)
|
|
- [Bootrom](#bootrom)
|
|
- [On the Proxmark3, for receiving frames](#on-the-proxmark3-for-receiving-frames-1)
|
|
- [On the Proxmark3, for sending frames](#on-the-proxmark3-for-sending-frames-1)
|
|
- [On the client, for sending frames](#on-the-client-for-sending-frames-1)
|
|
- [On the client, for receiving frames](#on-the-client-for-receiving-frames-1)
|
|
- [New usart RX FIFO](#new-usart-rx-fifo)
|
|
- [Timings](#timings)
|
|
- [Reference frames](#reference-frames)
|
|
|
|
## Old format
|
|
^[Top](#top)
|
|
|
|
Previously, frames were, in both directions like this:
|
|
|
|
uint64_t cmd;
|
|
uint64_t arg[3];
|
|
union {
|
|
uint8_t asBytes[PM3_CMD_DATA_SIZE];
|
|
uint32_t asDwords[PM3_CMD_DATA_SIZE / 4];
|
|
} d;
|
|
|
|
with PM3_CMD_DATA_SIZE = 512 and there was no API abstraction, everybody was forging/parsing these frames.
|
|
These two structs now use `PM3_CMD_DATA_SIZE_OLD`, pinned at 512 independently of `PM3_CMD_DATA_SIZE`:
|
|
the bootloader only speaks OLD, so growing them would break flashing against every deployed bootrom.
|
|
So the frame size was fixed, 544 bytes, even for simple ACKs.
|
|
When snooping the USB transfers, we can observe the host is sending 544b Bulk USB frames while the Proxmark3 is limited by its internal buffers and is sending 128b, 128b, 128b, 128b, 32b, so in total 5 packets.
|
|
|
|
## New format
|
|
^[Top](#top)
|
|
|
|
Even if we make the payload part variable in the old format, we've still a minimum of 32 bytes per frame with fields arbitrarily large.
|
|
So we designed a new format from scratch:
|
|
|
|
For commands being sent to the Proxmark3:
|
|
|
|
uint32_t magic;
|
|
uint16_t length : 15;
|
|
bool ng : 1;
|
|
uint16_t cmd;
|
|
uint8_t data[length];
|
|
uint16_t crc;
|
|
|
|
* `magic`: arbitrary magic (`PM3a`) to help re-sync if needed
|
|
* `length`: length of the variable payload, 0 if none, max 512 (PM3_CMD_DATA_SIZE) for now.
|
|
* `ng`: flag to tell if the data is following the new format (ng) or the old one, see transition notes below
|
|
* `cmd`: as previously, on 16b as it's enough
|
|
* `data`: variable length payload
|
|
* `crc`: either an actual CRC (crc14a) or a Magic placeholder (`a3`)
|
|
|
|
For responses from the Proxmark3:
|
|
|
|
uint32_t magic;
|
|
uint16_t length : 15;
|
|
bool ng : 1;
|
|
int8_t status;
|
|
int8_t reason;
|
|
uint16_t cmd;
|
|
uint8_t data[length];
|
|
uint16_t crc;
|
|
|
|
* `magic`: arbitrary magic (`PM3b`) to help re-sync if needed
|
|
* `length`: length of the variable payload, 0 if none, max 512 (PM3_CMD_DATA_SIZE) for now.
|
|
* `ng`: flag to tell if the data is following the new format (ng) or the old one, see transition notes below
|
|
* `status`: a field to send back the status of the command execution
|
|
* `reason`: details about what the status indicates for the specified command
|
|
* `cmd`: as previously, on 16b as it's enough
|
|
* `data`: variable length payload
|
|
* `crc`: either an actual CRC (crc14a) or a Magic placeholder (`b3`)
|
|
|
|
We used to send an anonymous ACK, now we're replying with the corresponding command name and a status.
|
|
CRC is optional and on reception, the magic `a3`/`b3` is accepted as placeholder. If it's different then it's checked as a CRC.
|
|
By default CRC is used over USART and is disabled over USB, on both directions.
|
|
|
|
Internal structures used to handle these packets are:
|
|
* PacketCommandNGPreamble
|
|
* PacketCommandNGPostamble
|
|
* PacketCommandNGRaw
|
|
* PacketResponseNGPreamble
|
|
* PacketResponseNGPostamble
|
|
* PacketResponseNGRaw
|
|
|
|
But they are abstracted from the developer view with a new API. See below.
|
|
|
|
## Transition
|
|
^[Top](#top)
|
|
|
|
**Status: the C client and the ARM firmware are converted.**
|
|
|
|
The client has no `SendCommandOLD` or `SendCommandMIX` call sites left. On the
|
|
device only three legacy replies remain, and all three are deliberate:
|
|
|
|
| Site | Why it stays |
|
|
|---|---|
|
|
| `armsrc/appmain.c` — `CMD_READ_MEM_DOWNLOADED` and its `CMD_ACK` terminator | also served by `bootrom.c`, which only speaks OLD |
|
|
| `armsrc/appmain.c` — `CMD_DEVICE_INFO` | same, see `bootrom.c` |
|
|
|
|
`SendCommandBL` marks the frames that must stay OLD because the bootloader
|
|
serves them. Do not "convert" those.
|
|
|
|
These sites chunk by `PM3_CMD_DATA_SIZE_OLD`, not `PM3_CMD_DATA_SIZE`: `reply_old`
|
|
clamps its payload to the OLD size, so a sender chunking by the NG size would build
|
|
oversized chunks, have them truncated on the wire, and still announce the full length
|
|
in `oldarg[1]`.
|
|
|
|
`armsrc/hfsnoop.c` — `CMD_FPGAMEM_DOWNLOADED` used to be on this list because its
|
|
FPGA trace loop is a DMA double-buffer and an NG header did not obviously fit
|
|
alongside a full DMA buffer. It is converted: the DMA writes straight into
|
|
`chunk->data` of a `download_chunk_t`, so a filled buffer is already a complete NG
|
|
payload. Note the loop arms each transfer for exactly the bytes still expected -
|
|
`FPGA_TRACE_SIZE` is not a multiple of `DOWNLOAD_CHUNK_MAX`, and arming a full
|
|
chunk for the short last one waits forever on bytes the FPGA never sends.
|
|
|
|
`PacketResponseNG.oldarg[]` is likewise almost gone on the client. The only
|
|
readers left are `client/src/flash.c` and `client/src/proxmark3.c`, both talking
|
|
to the bootrom over `SendCommandBL`. The Lua binding no longer serialises the
|
|
oldargs into the response it hands scripts.
|
|
|
|
The old frames are still supported by the transport, so `PacketCommandOLD` and
|
|
`PacketResponseOLD` remain, abstracted from the developer view by the new API.
|
|
|
|
## New format API
|
|
^[Top](#top)
|
|
|
|
So the new API is a merge of the old and the new frame formats, to ensure a smooth transition.
|
|
|
|
The boolean `ng` indicates if the structure is storing data from the old or the new format.
|
|
Old format can come from either old 544b frames or mixed frames (variable length but still with oldargs).
|
|
After the full transition, we might remove the fields `oldarg` and `ng`.
|
|
`PacketCommandNG` and `PacketResponseNG` are the structs used by the API, as seen in a previous section, there are other variable-sized packed structs specifically for the data transmission.
|
|
|
|
typedef struct {
|
|
uint16_t cmd;
|
|
uint16_t length;
|
|
uint32_t magic; // NG
|
|
uint16_t crc; // NG
|
|
uint64_t oldarg[3]; // OLD
|
|
union {
|
|
uint8_t asBytes[PM3_CMD_DATA_SIZE];
|
|
uint32_t asDwords[PM3_CMD_DATA_SIZE / 4];
|
|
} data;
|
|
bool ng; // does it store NG data or OLD data?
|
|
} PacketCommandNG;
|
|
|
|
typedef struct {
|
|
uint16_t cmd;
|
|
uint16_t length;
|
|
uint32_t magic; // NG
|
|
int8_t status; // NG
|
|
int8_t reason; // NG
|
|
uint16_t crc; // NG
|
|
uint64_t oldarg[3]; // OLD
|
|
union {
|
|
uint8_t asBytes[PM3_CMD_DATA_SIZE];
|
|
uint32_t asDwords[PM3_CMD_DATA_SIZE / 4];
|
|
} data;
|
|
bool ng; // does it store NG data or OLD data?
|
|
} PacketResponseNG;
|
|
|
|
|
|
### On the client, for sending frames
|
|
^[Top](#top)
|
|
|
|
(`client/comms.c`)
|
|
|
|
void SendCommandNG(uint16_t cmd, uint8_t *data, size_t len);
|
|
void SendCommandBL(uint64_t cmd, uint64_t arg0, uint64_t arg1, uint64_t arg2, void *data, size_t len);
|
|
void SendCommandOLD(uint64_t cmd, uint64_t arg0, uint64_t arg1, uint64_t arg2, void *data, size_t len);
|
|
|
|
`SendCommandNG` is what every command uses. Put everything in an ad-hoc PACKED
|
|
struct in the `data` field.
|
|
|
|
`SendCommandBL` is for Bootloader-related activities, see the Bootrom section. It
|
|
is a thin alias over `SendCommandOLD` and exists so that the frames which *must*
|
|
stay OLD are visibly tagged as such. `SendCommandOLD` has no other caller.
|
|
|
|
`SendCommandMIX` and `PM3_CMD_DATA_SIZE_MIX` **have been removed.** MIX was the
|
|
halfway house: an NG-framed packet that still carried the three 64 bit oldargs in
|
|
the first 24 bytes of the payload. Nothing uses it any more, and the client can no
|
|
longer construct one.
|
|
|
|
Internally these functions prepare the frame and call `uart_communication` which
|
|
calls `uart_send`.
|
|
|
|
### On the Proxmark3, for receiving frames
|
|
^[Top](#top)
|
|
|
|
(`armsrc/appmain.c`)
|
|
|
|
PacketCommandNG
|
|
|
|
`AppMain` calls `receive_ng`(`common/cmd.c`) which calls `usb_read_ng`/`usart_read_ng` to get a `PacketCommandNG`, then passes it to `PacketReceived`.
|
|
(no matter if it's an old frame or a new frame, check `PacketCommandNG.ng` field to know if there are `oldargs`)
|
|
`PacketReceive` is the commands broker.
|
|
Old handlers will still find their stuff in `PacketCommandNG.oldarg` field.
|
|
|
|
### On the Proxmark3, for sending frames
|
|
^[Top](#top)
|
|
|
|
(`common/cmd.c`)
|
|
|
|
int reply_old(uint64_t cmd, uint64_t arg0, uint64_t arg1, uint64_t arg2, const void *data, size_t len);
|
|
int reply_ng(uint16_t cmd, int8_t status, const uint8_t *data, size_t len);
|
|
int reply_reason(uint16_t cmd, int8_t status, int8_t reason, const uint8_t *data, size_t len);
|
|
|
|
`reply_mix` **has been removed**. `reply_old` survives only for the handlers the
|
|
bootrom also serves; note it always transmits `sizeof(PacketResponseOLD)`, 544
|
|
bytes, no matter what `len` says, whereas `reply_ng` sends exactly what you give
|
|
it.
|
|
|
|
A handler now simply validates the length and answers on its own opcode:
|
|
|
|
case CMD_FOOBAR: {
|
|
if (packet->length != sizeof(foobar_t)) {
|
|
reply_ng(CMD_FOOBAR, PM3_EINVARG, NULL, 0);
|
|
break;
|
|
}
|
|
foobar_t *payload = (foobar_t *)packet->data.asBytes;
|
|
...
|
|
reply_ng(CMD_FOOBAR, PM3_SUCCESS, resp, resplen);
|
|
break;
|
|
}
|
|
|
|
During the transition some handlers carried a `if (packet->ng) { ... } else { ... }`
|
|
dual-mode branch so converted and unconverted callers could coexist. None remain;
|
|
a frame arriving without the `ng` bit is now answered with `PM3_EINVARG`.
|
|
|
|
### On the client, for receiving frames
|
|
^[Top](#top)
|
|
|
|
(`client/comms.c`)
|
|
|
|
WaitForResponseTimeout ⇒ PacketResponseNG
|
|
|
|
`uart_communication` calls `uart_receive` and create a `PacketResponseNG`, then passes it to `PacketResponseReceived`.
|
|
`PacketResponseReceived` treats it immediately (prints) or stores it with `storeReply`.
|
|
Commands do `WaitForResponseTimeoutW` (or `dl_it`) which uses `getReply` to fetch responses.
|
|
|
|
## API transition
|
|
^[Top](#top)
|
|
|
|
In short, to move from one format to the other, we need for each command:
|
|
|
|
* (client TX) `SendCommandOLD` ⇒ `SendCommandNG` (with all stuff in ad-hoc PACKED structs in `data` field)
|
|
* (pm3 RX) `PacketCommandNG` parsing, from `oldarg` to only the `data` field
|
|
* (pm3 TX) `reply_old` ⇒ `reply_ng` (with all stuff in ad-hoc PACKED structs in `data` field)
|
|
* (client RX) `PacketResponseNG` parsing, from `oldarg` to only the `data` field
|
|
|
|
A MIX frame was the historical halfway house (`SendCommandMIX` / `reply_mix`).
|
|
Do not add new ones: the client is free of them and every device handler that
|
|
mattered has been converted.
|
|
|
|
### Practical notes from converting the tree
|
|
|
|
* **Reply with the command's own opcode, never `CMD_ACK`.** An anonymous ACK is
|
|
what forced hacks like iCLASS putting `CMD_HF_ICLASS_SIMULATE` inside `arg0` of
|
|
its own reply so the client could tell replies apart.
|
|
* **A success flag belongs in the NG `status` field**, not in a data byte, and a
|
|
second discriminator can use `reply_reason()`.
|
|
* **Validate `packet->length` before casting**, on both sides. Several converted
|
|
commands previously read past the end of a short frame.
|
|
* **`PACKED` is not free.** It sets the struct's alignment to 1, so taking the
|
|
address of any member wider than a byte trips
|
|
`-Werror=address-of-packed-member`, and on the ARM7TDMI an unaligned 32 bit
|
|
load silently rotates rather than faulting. Pack a struct only to *remove*
|
|
padding: if `sizeof` is the same either way, leave it unpacked. Compare
|
|
`epa_replay_t` (packed, its `uint16_t`s sit at odd offsets) with
|
|
`epa_result_t` and `t55xx_setconfig_t` (not packed, they already tile and
|
|
their members get addressed).
|
|
* **`PM3_CMD_DATA_SIZE_MIX` is a MIX-only constant.** Any chunked transfer that
|
|
moves to NG must size its chunks as
|
|
`PM3_CMD_DATA_SIZE - sizeof(payload_t)` instead.
|
|
* **`reply_old` always transmits `sizeof(PacketResponseOLD)`**, 544 bytes,
|
|
whatever `len` says. `reply_ng` sends only what you give it.
|
|
* **A command can answer more than once.** `CMD_HF_ISO14443A_READER` with
|
|
`ISO14A_CONNECT | ISO14A_RAW` replies twice, select then raw exchange; the
|
|
client must consume both.
|
|
|
|
### Bulk downloads
|
|
|
|
`CMD_DOWNLOAD_BIGBUF`, `CMD_DOWNLOAD_EML_BIGBUF`, `CMD_SPIFFS_DOWNLOAD` and
|
|
`CMD_FLASHMEM_DOWNLOAD` use `download_req_t` / `download_chunk_t` /
|
|
`download_done_t` (see `include/pm3_cmd.h`). The chunk header carries only the
|
|
offset, since the frame length gives the size, and the transfer ends with a
|
|
`download_done_t` answered on the original `CMD_DOWNLOAD_*` opcode rather than an
|
|
anonymous ACK. `dl_it()` in `client/src/comms.c` still understands the OLD chunk
|
|
format because `CMD_READ_MEM_DOWNLOAD` is served by the bootrom.
|
|
|
|
## Bootrom
|
|
^[Top](#top)
|
|
|
|
Bootrom code will still use the old frame format to remain compatible with other repos supporting the old format and because it would hardly gain anything from the new format:
|
|
* almost all frames convey 512b of payload, so difference in overhead is negligible
|
|
* bringing flash over usart sounds risky and would be terribly slow anyway (115200 bauds vs. 7M bauds).
|
|
|
|
`SendCommandBL` is the same as `SendCommandOLD` with a different name to be sure not to migrate it.
|
|
|
|
### On the Proxmark3, for receiving frames
|
|
^[Top](#top)
|
|
|
|
(`bootrom/bootrom.c`)
|
|
|
|
usb_read (common/usb_cdc.c) ⇒ UsbPacketReceived (bootrom.c)
|
|
⇒ CMD_DEVICE_INFO / CMD_START_FLASH / CMD_FINISH_WRITE / CMD_HARDWARE_RESET
|
|
|
|
also `usb_enable`, `usb_disable` (`common/usb_cdc.c`)
|
|
|
|
### On the Proxmark3, for sending frames
|
|
^[Top](#top)
|
|
|
|
(`bootrom/bootrom.c`)
|
|
|
|
reply_old (bootrom.c) ⇒ usb_write (common/usb_cdc.c)
|
|
|
|
also `usb_enable`, `usb_disable` (`common/usb_cdc.c`)
|
|
|
|
### On the client, for sending frames
|
|
^[Top](#top)
|
|
|
|
Therefore, the flasher client (`client/flasher.c` + `client/flash.c`) must still use these old frames.
|
|
It uses a few commands in common with current client code:
|
|
|
|
OpenProxmark
|
|
CloseProxmark
|
|
SendCommandOLD
|
|
⇒ CMD_DEVICE_INFO / CMD_START_FLASH / CMD_FINISH_WRITE / CMD_HARDWARE_RESET
|
|
|
|
### On the client, for receiving frames
|
|
^[Top](#top)
|
|
|
|
As usual, old frames are still supported
|
|
|
|
WaitForResponseTimeout ⇒ PacketResponseNG
|
|
|
|
## New usart RX FIFO
|
|
^[Top](#top)
|
|
|
|
USART code has been rewritten to cope with unknown size packets.
|
|
* using USART full duplex with double DMA buffer on RX & TX
|
|
* using internal FIFO for RX
|
|
|
|
`usart_init`:
|
|
* USART is activated all way long from usart_init(), no need to touch it in RX/TX routines: `pUS1->US_PTCR = AT91C_PDC_RXTEN | AT91C_PDC_TXTEN`
|
|
|
|
`usart_writebuffer_sync`:
|
|
* still using DMA but accepts arbitrary packet sizes
|
|
* removed unneeded memcpy
|
|
* wait for DMA buffer to be treated before returning, therefore "sync"
|
|
* we could make an async version but caller must be sure the DMA buffer remains available!
|
|
* as it's sync, no need for next DMA buffer
|
|
|
|
`usart_read_ng`:
|
|
* user tells expected packet length
|
|
* relies on usart_rxdata_available to know if there is data in our FIFO buffer
|
|
* fetches data from our FIFO
|
|
* dynamic number of tries (depending on FPC speed) to wait for asked data
|
|
|
|
`usart_rxdata_available`:
|
|
* polls usart_fill_rxfifo
|
|
* returns number of bytes available in our FIFO
|
|
|
|
`usart_fill_rxfifo`:
|
|
* if next DMA buffer got moved to current buffer (`US_RNCR == 0`), it means one DMA buffer is full
|
|
* transfer current DMA buffer data to our FIFO
|
|
* swap to the other DMA buffer
|
|
* provide the emptied DMA buffer as next DMA buffer
|
|
* if current DMA buffer is partially filled
|
|
* transfer available data to our FIFO
|
|
* remember how many bytes we already copied to our FIFO
|
|
|
|
## Timings
|
|
^[Top](#top)
|
|
|
|
Reference (before new format):
|
|
|
|
linux usb: #db# USB Transfer Speed PM3 ⇒ Client = 545109 Bytes/s
|
|
On a Windows VM:
|
|
|
|
proxspace usb: #db# USB Transfer Speed PM3 ⇒ Client = 233998 Bytes/s
|
|
|
|
Over USART:
|
|
|
|
(`common/usart.h`)
|
|
USART_BAUD_RATE defined there
|
|
|
|
9600: #db# USB Transfer Speed PM3 ⇒ Client = 934 Bytes/s
|
|
115200: #db# USB Transfer Speed PM3 ⇒ Client = 11137 Bytes/s
|
|
460800: #db# USB Transfer Speed PM3 ⇒ Client = 43119 Bytes/s
|
|
linux usb: #db# USB Transfer Speed PM3 ⇒ Client = 666624 Bytes/s (equiv. to ~7Mbaud)
|
|
|
|
|
|
(`pm3_cmd.h`)
|
|
|
|
Receiving from USART need more than 30ms as we used on USB
|
|
else we get errors about partial packet reception
|
|
|
|
FTDI 9600 hw status ⇒ we need 20ms
|
|
FTDI 115200 hw status ⇒ we need 50ms
|
|
FTDI 460800 hw status ⇒ we need 30ms
|
|
BT 115200 hf mf fchk --1k -f file.dic ⇒ we need 140ms
|
|
|
|
# define UART_FPC_CLIENT_RX_TIMEOUT_MS 200
|
|
# define UART_USB_CLIENT_RX_TIMEOUT_MS 20
|
|
# define UART_NET_CLIENT_RX_TIMEOUT_MS 500
|
|
# define UART_TCP_LOCAL_CLIENT_RX_TIMEOUT_MS 40
|
|
# define UART_UDP_LOCAL_CLIENT_RX_TIMEOUT_MS 20
|
|
|
|
This goes to `uart_posix.c` `timeval` struct
|
|
and `uart_win32.c` `serial_port_windows` struct
|
|
|
|
It starts at UART_FPC_CLIENT_RX_TIMEOUT_MS and once we detect we're working over USB
|
|
it's reduced to UART_USB_CLIENT_RX_TIMEOUT_MS.
|
|
|
|
The timeout is configurable by the `hw timeout` command (since v4.17140).
|
|
|
|
Add automatically some communication delay in the `WaitForResponseTimeout` & `dl_it` timeouts.
|
|
Only when using FPC, timeout = 2* empirically measured delay (FTDI cable).
|
|
Empirically measured delay (FTDI cable) with "hw ping -l 512" :
|
|
|
|
usb ⇒ 6.. 32ms
|
|
460800 ⇒ 40.. 70ms
|
|
9600 ⇒ 1100..1150ms
|
|
|
|
(`client/comms.c`)
|
|
|
|
static size_t communication_delay(void) {
|
|
if (conn.send_via_fpc_usart) // needed also for Windows USB USART??
|
|
return 2 * (12000000 / uart_speed);
|
|
return 100;
|
|
}
|
|
|
|
Because some commands send a lot of frames before finishing (hw status, lf read,...),
|
|
`WaitForResponseTimeout` & `dl_it` timeouts are reset at each packet reception,
|
|
so timeout is actually counted after latest received packet,
|
|
it doesn't depend anymore on the number of received packets.
|
|
|
|
It was needed to tune pm3 RX usart `maxtry` :
|
|
|
|
(`common/usart.c`)
|
|
|
|
uint32_t usart_read_ng(uint8_t *data, size_t len) {
|
|
// Empirical max try observed: 3000000 / USART_BAUD_RATE
|
|
// Let's take 10x
|
|
uint32_t tryconstant = 0;
|
|
#ifdef USART_SLOW_LINK
|
|
// Experienced up to 13200 tries on BT link even at 460800
|
|
tryconstant = 50000;
|
|
#endif
|
|
uint32_t maxtry = 10 * (3000000 / USART_BAUD_RATE) + tryconstant;
|
|
|
|
|
|
`DbpStringEx` using `reply_old`:
|
|
|
|
time client/proxmark3 -p /dev/ttyACM0 -c "hw status"
|
|
2.52s
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 460800 -c "hw status"
|
|
3.03s
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 115200 -c "hw status"
|
|
4.88s
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 9600 -c "hw status"
|
|
26.5s
|
|
|
|
`DbpStringEx` using `reply_mix`:
|
|
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 9600 -c "hw status"
|
|
7.08s
|
|
|
|
`DbpStringEx` using `reply_ng`:
|
|
|
|
time client/proxmark3 -p /dev/ttyACM0 -c "hw status"
|
|
2.10s
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 460800 -c "hw status"
|
|
2.22s
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 115200 -c "hw status"
|
|
2.43s
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 9600 -c "hw status"
|
|
5.75s
|
|
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 9600 -c "lf read"
|
|
50.38s
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 115200 -c "lf read"
|
|
6.28s
|
|
|
|
time client/proxmark3 -p /dev/ttyACM0 -c "mem dump -f foo_usb"
|
|
1.48s
|
|
time client/proxmark3 -p /dev/ttyUSB0 -b 115200 -c "mem dump -f foo_fpc"
|
|
25.34s
|
|
|
|
|
|
Sending multiple commands can still be slow because it waits regularly for incoming RX frames and the timings are quite conservative because of BT (see struct timeval timeout in uart_posix.c, now at 200ms). When one knows there is no response to wait before the next command, he can use the same trick as in the flasher:
|
|
|
|
// fast push mode
|
|
conn.block_after_ACK = true;
|
|
some loop {
|
|
if (sending_last_command)
|
|
// Disable fast mode
|
|
conn.block_after_ACK = false;
|
|
SendCommandOLD / SendCommandMix
|
|
if (WaitForResponseTimeout(CMD_ACK, &resp, some_timeout) == false) {
|
|
....
|
|
conn.block_after_ACK = false;
|
|
return PM3_ETIMEOUT;
|
|
}
|
|
}
|
|
return PM3_SUCCESS;
|
|
|
|
Or if it's too complex to determine when we're sending the last command:
|
|
|
|
// fast push mode
|
|
conn.block_after_ACK = true;
|
|
some loop {
|
|
SendCommandNG
|
|
if (WaitForResponseTimeout(CMD_FOOBAR, &resp, some_timeout) == false) {
|
|
....
|
|
conn.block_after_ACK = false;
|
|
return PM3_ETIMEOUT;
|
|
}
|
|
}
|
|
// Disable fast mode and send a dummy command to make it effective
|
|
conn.block_after_ACK = false;
|
|
SendCommandNG(CMD_PING, NULL, 0);
|
|
WaitForResponseTimeout(CMD_ACK, NULL, 1000);
|
|
return PM3_SUCCESS;
|
|
|
|
|
|
## Reference frames
|
|
^[Top](#top)
|
|
|
|
For helping debug...
|
|
|
|
* OLD command and reply packets are 544 bytes.
|
|
* NG & MIX command packets are between 10 and 522 bytes.
|
|
* NG & MIX reply packets are between 12 and 524 bytes.
|
|
|
|
On linux USB
|
|
* sent packets can be 544
|
|
* received packets are max 128, so 544 = 128+128+128+128+32
|
|
|
|
On linux UART (FTDI)
|
|
* sent packets are max 256, so 544 = 256+256+32
|
|
* received packets are max 512, so 544 = 512+32
|
|
|
|
`hw ping` (old version, mix reply)
|
|
|
|
TestProxmark: SendCommandOLD(CMD_PING, 0, 0, 0, NULL, 0);
|
|
->544=0901000000000000000000000000000000000000000000000000000000000000 -> OLD
|
|
CMD_PING: reply_mix(CMD_ACK, reply_via_fpc, 0, 0, 0, 0);
|
|
<-36=504d336218000000ff0000000000000000000000000000000000000000000000 <- MIX
|
|
|
|
`hw ping` (intermediate version using MIX)
|
|
|
|
CmdPing SendCommandMIX(CMD_PING, 0, 0, 0, NULL, 0);
|
|
->34=504d336118000901000000000000000000000000000000000000000000000000 -> MIX
|
|
CMD_PING reply_mix(CMD_ACK, reply_via_fpc, 0, 0, 0, 0);
|
|
<-36=504d336218000000ff0000000000000000000000000000000000000000000000 <- MIX
|
|
|
|
`hw ping` (current NG version)
|
|
|
|
CmdPing SendCommandNG(CMD_PING, data, len);
|
|
->10=504d3361008009016133 -> NG
|
|
CMD_PING reply_ng(CMD_PING, PM3_SUCCESS, packet->data.asBytes, packet->length);
|
|
<-12=504d33620080000009016233 <- NG
|
|
|
|
`hw ping -l 512` (NG)
|
|
|
|
CmdPing SendCommandNG(CMD_PING, data, len);
|
|
->522=504d336100820901000102030405060708090a0b0c0d0e0f1011121314151617 -> NG
|
|
CMD_PING reply_ng(CMD_PING, PM3_SUCCESS, packet->data.asBytes, packet->length);
|
|
<-128=504d3362008200000901000102030405060708090a0b0c0d0e0f101112131415 <- NG
|
|
<-128=767778797a7b7c7d7e7f808182838485868788898a8b8c8d8e8f909192939495
|
|
<-128=f6f7f8f9fafbfcfdfeff000102030405060708090a0b0c0d0e0f101112131415
|
|
<-128=767778797a7b7c7d7e7f808182838485868788898a8b8c8d8e8f909192939495
|
|
<-12=f6f7f8f9fafbfcfdfeff6233
|
|
|