Tesso M Costa
b3c638842e
Boot TX power was left at a conservative 10dBm (Heltec V4's pattern) with no way to raise it, unlike the T-Deck which boots straight at the chip's real 22dBm ceiling. On hardware this was silently degrading outbound range: adverts/DMs sent from the pager were unreliable while inbound reception was fine, since the far node's own TX power was unaffected. 22dBm is confirmed as this chip's actual sub-GHz HP-PA ceiling via RadioLib's LR1120::checkOutputPower() (LR1121 inherits it) and matches trail-mate's own working config for this board. Also widen the three RX-boosted-gain gates in MyMesh.cpp/DataStore.cpp that only checked USE_SX1262/USE_SX1268 to include USE_LR1121 -- CustomLR1121Wrapper already implements setRxBoostedGainMode/ getRxBoostedGainMode, so the setting was silently a no-op for this radio. Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
A real touchscreen UI for your mesh radio. · open source · GPL-3.0
Touch-UI MeshCore companion-radio firmware for the LilyGo T-Deck / T-Deck Plus and Heltec V4 + TFT (ESP32-S3).
An LVGL touch UI — map, chat, contacts, channels, settings — split out of
meshcomod. The app depends on a
MeshCore fork via PlatformIO lib_deps.
Boards
- LilyGo T-Deck / T-Deck Plus — env
LilyGo_TDeck_companion_radio_touch - Heltec V4 + TFT + CHSC6x touch — env
heltec_v4_tft_companion_radio_usb_tcp_touch
Architecture
This repo holds only the app: the companion_radio glue, the ui-touch
LVGL UI, the two boards' glue/variants, and platformio.ini. The MeshCore
core is not vendored here — it's pulled as a library via lib_deps from the
ALLFATHER-BV/meshcomod monorepo
(the same repo as the non-touch firmware), pinned by a lean source-only core-*
git tag. The touch-app files this repo owns (TouchPrefsStore, WifiRuntimeStore,
the transports, …) are dropped from the lib via -DMC_VENDORED_TOUCH_APP so they
aren't compiled twice. The build is byte-identical to the original in-tree
meshcomod firmware.
Build
PlatformIO pulls the core fork and all libraries automatically:
pio run -e heltec_v4_tft_companion_radio_usb_tcp_touch # Heltec V4 TFT
pio run -e LilyGo_TDeck_companion_radio_touch # LilyGo T-Deck
# or just `pio run` to build both
Flash with the NVS-preserving 4-component chain (bootloader / partitions /
boot_app0 / firmware at 0x0 / 0x8000 / 0xe000 / 0x10000) so saved Wi-Fi
credentials survive — not a merged image, which 0xFF-pads and wipes NVS.
Contributing
Contributions are welcome — see CONTRIBUTING.md. One topic per PR; inbound contributions are accepted under the project's GPL-3.0 license.
License
GPL-3.0-or-later — see LICENSE. wadamesh is copyleft: anyone who distributes a build or a fork must also make their source available under the GPL. This keeps the UI open and concentrates community effort instead of fragmenting it into closed forks.
wadamesh incorporates and depends on MeshCore (MIT, © Scott Powell / rippleradios.com) and other third-party components — see NOTICE for the full list and their licenses. MeshCore-derived files keep their MIT notices; the combined work is distributed under the GPL (MIT is GPL-compatible). The MeshCore fork that wadamesh builds against stays MIT on purpose, so its Wi-Fi/BLE hooks remain upstreamable to MeshCore.