* room server: added RegionMap, and new CommonCLI wiring, default_scope handling
* sensor: only minimal RegionMap wiring. Still needs work to handle default-scope
Resolve conflicts: keep both Ethernet CLI and SenseCAP power-off
button code in repeater, keep both Ethernet docs and power management
CLI docs.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
The Ethernet retry loop in repeater and room server checked
hardwareStatus() and linkStatus() before calling Ethernet.begin(),
which always returned EthernetNoHardware since hardware detection
only happens during begin(). Extract shared Ethernet CLI code into
EthernetCLI.h to prevent future divergence. Also fix time_t type
mismatch in companion radio Ethernet init.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Rename eth command to eth.status for consistency with other commands
- Rename generateDeviceMac to generateEthernetMac for clarity
- Refactor ethernet_handle_command to return false by default
- Allow new TCP clients to replace existing connections (repeater, room server, SerialEthernetInterface)
- Boot companion radio without Ethernet on init failure (LoRa-only recovery mode)
- Remove > prompt from ethernet CLI for consistency with serial interface
- Fix variable redeclaration compile error in SerialEthernetInterface when ETHERNET_STATIC_IP is defined
- Fix TCP socket leak when duplicate client detection fires
- Remove dead recv_queue and adv_restart_time members from SerialEthernetInterface
- Fix port numbers in docs (port 23 for repeater/room server CLI, port 5000 for companion radio)
- Clarify eth.status command is only available in repeater and room server firmware
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add W5100S Ethernet adapter support for RAK4631-based firmware, enabling
TCP CLI access on port 23 as an alternative to BLE/Serial connections.
- New SerialEthernetInterface for nRF52 with DHCP, reconnection handling,
and shared WB_IO2 power pin management with GPS module
- Ethernet build targets for repeater, room server, and companion firmware
- Prevent GPS from toggling WB_IO2 when Ethernet module is active
- CI build check for all three ETH firmware targets
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Instead of overloading getOutboundCount() with a magic sentinel value,
add a dedicated getOutboundTotal() method to the PacketManager interface
that returns the total queue size without time filtering.
This eliminates the fragile convention that caused the regression and
makes the two operations — time-filtered count vs total count —
explicitly separate in the API.
This change addresses two issues. The first is that the
LilyGo_TLora_V2_1_1_6_terminal_chat build would try to compile
simple_repeater/MyMesh.cpp. All other examples of terminal chat
targets are instead building simple_secure_chat/main.cpp . This
change would align this build to the rest of the builds.
The second issue, found during the course of investigating the
first, stems from simple_repeater/MyMesh.cpp using the
MAX_NEIGHBOURS #define to control whether the neighbor list is kept.
Repeaters that keep this list must define this value, and if the
value is not defined, then all neighbor-related functionality is
compiled out. However, the code that replies to
REQ_TYPE_GET_NEIGHBOURS did not properly check for this #define,
and thus any target that compiles simple_repeater/MyMesh.cpp
without defining MAX_NEIGHBOURS would get an undefined variable
compilation error.
As a practical matter though, there are no targets that compile
simple_repeater/MyMesh.cpp AND do not define MAX_NEIGHBOURS,
except this build due to the first issue. As a result, the
second issue is addressed only as a matter of completeness. The
expected behavior with this change is that such a repeater would
send a valid reply indicating zero known neighbors.
Ryan Gregg