Commit Graph
3785 Commits
Author SHA1 Message Date
Martin BoissonneaultandClaude Opus 5.5 9bf8f92df5 gps: don't let the settle time close a periodic window before the time sync
In periodic mode a window closed after GPS_FIX_SETTLE_MS (10 s) from the
first fix even if the clock sync was still pending. The sync needs about
4 s of continuous valid fixes (time_valid > 2, reset on any pass without
a fix), so after a hot start, when the receiver reports a fix within
seconds but not yet steadily, the window could close unsynced. On a
board without an RTC the clock then stays at its default until the next
window, a whole period later.

Close the window only once the sync has been tried (done, not needed, or
refused by GPS_GUARD); the settle time and the satellite count apply
after that. The acquisition timeout still bounds the window.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 18:23:54 -05:00
Marcel Verdult 7f7512d94c rak: keep WB_IO2 driven HIGH after a failed RAK12500 probe (#3834)
The I2C probe left WB_IO2 as an input when no RAK12500 answered. WB_IO2
switches the 3V3_S slot rail, which also powers a serial GPS. On base
boards that pull this line low, the serial GPS lost power right after
detection and never got a fix (#3830). Before df5a768c the pin stayed
HIGH, so keep it driven HIGH again. WB_IO4 and WB_IO5 still go back to
inputs.
2026-11-14 08:13:08 -04:00
Liam Cottle a4c66307a8 Merge pull request #3032 from Quency-D/heltec-rc52
Add heltec rc52
2026-11-14 10:43:40 +13:00
fdlamotte 888c7ca083 Merge pull request #3821 from AlexandrTyshchenko/feature/gps-guard-3d-fix
GPS: keep the GPS on for a 3D fix, prefer a recent 3D fix over a 2D one
2026-11-13 14:48:56 -04:00
fdlamotte 65cae3bc1c Merge branch 'dev' into feature/gps-guard-3d-fix 2026-11-13 14:48:02 -04:00
fdlamotte 7a900cf1c8 Merge pull request #3823 from AlexandrTyshchenko/fix/gps-first-fix-timeout
Limit the first periodic GPS acquisition after boot
2026-11-13 14:47:17 -04:00
Olexandr Tyshchenko 402abb7dbd GPS: accept a 2D fix, but keep the GPS on for a 3D fix
Per review: a 2D fix is valid, only less precise, and in some places a
receiver never gets a 3D fix. So the guard no longer rejects it; instead
the fix mode decides when the GPS may sleep:

- the fix mode is read from GSA for every NMEA receiver, not only with
  GPS_GUARD (`fm:` in `gps diag`), and stored with the last fix;
- in periodic mode, and for `gps once`, the GPS sleeps only after a 3D
  fix (or a fix from a receiver that does not report the mode); after a
  2D fix it stays on up to the acquisition timeout;
- a 2D fix does not replace a 3D fix younger than 5 min
  (GPS_3D_FIX_PREFERRED_MS).
2026-11-13 14:30:24 +02:00
Olexandr Tyshchenko 069b9fdaf8 GPS: first fix timeout as a saved setting (gps firstfix), 1 h by default
A cold start can take up to ~30 min with a weak sky view, so the default
limit before the first fix since boot goes from 15 min to 1 h.

The limit is now a GPS preference, set with `gps firstfix <duration>`
(0 = no limit, at most 1 day) and saved with the other GPS settings, so
repeaters and companions can use different values without a rebuild.
GPS_FIRST_FIX_TIMEOUT_MS stays as the build default.
2026-11-13 14:29:02 +02:00
Olexandr Tyshchenko ac2bf9372a Limit the first periodic GPS acquisition after boot
Before the first fix since boot, a periodic acquisition had no timeout. If no
fix is accepted (no sky view, no antenna, or a guard rejecting spoofed fixes),
the receiver then stayed on until a fix was accepted.

Give that window its own limit, GPS_FIRST_FIX_TIMEOUT_MS (15 min by default,
enough for a full almanac; 0 keeps the old behaviour). It counts as a miss and
the next acquisition starts after the configured period.
2026-11-12 10:48:10 +02:00
Quency-D 242b5db7fa Fix RC52 unused SPI1 MISO pin mapping
Use pin index 0, which maps to NRFX_SPIM_PIN_NOT_USED, to avoid the nRF52 SPI constructor indexing g_ADigitalPinMap[255]. Remove the absent MISO shutdown reset so the sentinel cannot reset physical P0.00. Follows the variant-side fixes in #3188 and #3189.

Validated heltec_rc52_repeater and heltec_rc52_companion_radio_ble builds. ELF disassembly confirms the MISO lookup uses map[0]=0xFF instead of the +1020-byte read and shutdown has no P0.00 reset. No hardware testing performed.
2026-11-12 15:54:21 +08:00
Quency-D dd83853585 Fix RC52 companion radio builds 2026-11-12 14:20:08 +08:00
Quency-D 38d95975e8 Merge pull request #20 from meshcore-dev/dev
merge Dev
2026-11-12 14:03:11 +08:00
Liam Cottle bb870313e4 Merge pull request #3822 from liamcottle/fix/3811
fix for mdns string not compiling due to ambiguous overload
2026-11-12 16:10:48 +13:00
liamcottle e3c1c34828 fix for mdns string not compiling due to ambiguous overload 2026-11-12 16:08:30 +13:00
Olexandr Tyshchenko 172e9d4290 GPS guard: reject a fix the receiver reports as 2D (GSA)
The guard checked satellites and HDOP but not the fix type. When the
receiver sends GSA, a fix it reports as 2D or no-fix is now rejected
(`rej 2d`). Receivers without GSA are unchanged (fix mode unknown).
GPS_GUARD_REQUIRE_3D=0 turns the check off. `gps diag` shows the fix
mode as `fm`.
2026-11-12 00:34:05 +02:00
fdlamotte 7812ecaea6 Merge pull request #3819 from nullrouten0/fix/gps-nmea-buffer-tail
GPS: stop MicroNMEA reading past the NMEA buffer
2026-11-11 18:29:30 -04:00
nullrouten0andClaude Sonnet 5.5 e1c1d76c5f GPS: stop MicroNMEA reading past the NMEA buffer
Add a 16-byte zeroed tail behind the 100-byte NMEA buffer. MicroNMEA's
fixed-width field skips can read a few bytes past the end of a malformed
sentence; with the tail those reads land on NUL bytes.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-11-11 17:58:36 +00:00
fdlamotte 6e6b7b105f Merge pull request #3817 from AlexandrTyshchenko/docs/gps-guard-alert-telemetry
GPS guard: drop leftovers of the alert telemetry channel
2026-11-11 10:39:49 -04:00
Olexandr Tyshchenko b920e7d249 GPS guard: drop leftovers of the alert telemetry channel
#3813 removed the telemetry channel for the GPS time alert. Remove the
docs sentence that still described it and the now unused
GpsGuard::getAlertOffset().
2026-11-11 16:18:58 +02:00
fdlamotte c4258a5beb Merge pull request #3801 from AlexandrTyshchenko/feature/gps-guard-time-wait
GPS guard: show "time wait" instead of "rej nofix" between fixes
2026-11-11 10:13:11 -04:00
fdlamotte 0f51fd70e7 Merge pull request #3815 from fdlamotte/advert_loc_pref
CommonCLI: get/set loc to replace gps advert command
2026-11-11 10:11:49 -04:00
Florent bed7286192 CommonCLI: get/set loc to replace gps advert command 2026-11-11 09:52:03 -04:00
fdlamotte 1e384b109d Merge pull request #3813 from fdlamotte/gps_guard_telem_removal
gps_guard: remove time alert telemetry
2026-11-11 08:06:44 -04:00
fdlamotte d1d802717a Merge pull request #3811 from fdlamotte/mdns_using_char
companion_radio: rewrite mdns part removing String class
2026-11-11 07:58:59 -04:00
Florent 79e0f4eafe gps_guard: remove time alert telemetry 2026-11-11 07:58:39 -04:00
fdlamotte 5a762ad907 Merge pull request #3812 from fdlamotte/revert-3784
Revert "Merge pull request #3784 from Maxwell456/feature/repeater-his…
2026-11-11 07:52:27 -04:00
Florent 74f1f5a156 Revert "Merge pull request #3784 from Maxwell456/feature/repeater-history"
This reverts commit f678f6ac15, reversing
changes made to b8ae75d258.
2026-11-11 07:49:41 -04:00
Florent 85bba10742 companion_radio: rewrite mdns part removing String class 2026-11-11 07:37:24 -04:00
fdlamotte e7c6d079cc Merge pull request #3810 from fdlamotte/revert_rak13302_tests
tests: revert rak13302 tests
2026-11-11 07:30:25 -04:00
Florent 0147165b14 tests: revert rak13302 tests 2026-11-11 07:26:01 -04:00
Liam Cottle 09eac55bc3 Merge pull request #3807 from Valentin-Metz/fix/cli-reply-buffer-overflow
Fix stack-buffer overflow in CLI reply buffers
2026-11-11 17:37:42 +13:00
Valentin Metz 224658694f Fix stack-buffer overflow in CLI reply buffers
The remote-CLI reply buffers in onPeerDataRecv() (repeater, room server,
sensor) and BaseChatMesh were sized temp[166] for a 5-byte datagram
header plus 161 bytes of reply. But MyMesh::handleCommand() first
reflects a 3-byte correlation prefix (e.g. 'aa|') into the reply, after
which CommonCLI commands may write up to 160 chars + NUL into the
remaining 158 bytes -- overflowing the buffer by 2 bytes (e.g. a full
'regions' listing via exportTo(reply, 160)).

Triggering this remotely crashes the node (observed as an unresponsive
repeater after a prefixed 'regions' query); the 2 out-of-bounds bytes
are a printable region-name character and a NUL.

Size the buffers for the full worst case instead:
5 header + 3 prefix + 160 reply + 1 NUL = 169.

Verified with a host ASan harness reproducing the exact layout:
prefixed 'regions' with a 25-region listing overflowed temp[166]
(BufStream::write, RegionMap.cpp) and now passes clean with temp[169];
unprefixed (serial) path unaffected.
2026-11-11 05:30:54 +01:00
Olexandr Tyshchenko 196ca97751 GPS guard: show "time wait" instead of "rej nofix" between fixes
When the last GPS time check passed but there is no current trusted fix
(e.g. the GPS is asleep between periodic fixes), gps guard showed
"time rej nofix", which reads like a rejection although the clock is fine.
Show "time wait" instead. A real rejection without a trusted fix (GPS time
arriving while fixes are rejected) still shows "rej nofix".
2026-11-11 01:48:12 +02:00
fdlamotte ef4477b69d Merge pull request #3798 from AlexandrTyshchenko/feature/gps-baud-probe-list
GPS: GPS_BAUD_PROBE_LIST as a build flag for any NmeaGpsDriver; enable on Station G2/G3
2026-11-10 18:57:35 -04:00
Olexandr Tyshchenko ef6ef2e9d2 GPS: GPS_BAUD_PROBE_LIST as a build flag for any NmeaGpsDriver; enable on Station G2/G3
The probe list was wired only in variants/promicro/target.cpp. It is now the
default list of NmeaGpsDriver when GPS_BAUD_PROBE_LIST is set, so a variant
enables baud autodetection with a build flag alone.

Station G2 and G3 enable it: their Grove UART connector is used with M5Stack
Unit GPS modules, which default to 115200.
2026-11-10 23:51:29 +02:00
fdlamotte f678f6ac15 Merge pull request #3784 from Maxwell456/feature/repeater-history
Add min/max/avg history queries to repeaters
2026-11-10 12:42:53 -04:00
fdlamotte b8ae75d258 Merge pull request #3770 from lihardyextreme/feature-mdns
feat: mDNS ESP32 - enable local network discovery over mDNS
2026-11-10 12:07:18 -04:00
fdlamotte 44702f93a9 Merge pull request #3793 from fdlamotte/eink_hibernate_when_off
eink: some updates (busy loop + hibernate when screen off)
2026-11-10 12:00:43 -04:00
Florent 8d5bd2e2c7 eink: some updates (busy loop + hibernate when screen off) 2026-11-10 11:52:38 -04:00
fdlamotte be5efc242f Merge pull request #3778 from dahuib/rak16000-v1.18.0-clean
Support RAK16000 (INA219 at 0x41)
2026-11-10 11:45:43 -04:00
dahuib a655d1f785 Support RAK16000 (INA219 at 0x41) on dev 2026-11-10 15:57:32 +01:00
fdlamotte d495d2edf5 Merge pull request #3623 from BeGiBue/feature/wio-l1-eink-repeater
Add repeater environment for Wio Tracker L1 E-Ink
2026-11-10 09:06:45 -04:00
fdlamotte d1df7d2722 Merge pull request #3664 from Martin-hub1/dev
Add DFRobot LoRaWAN ESP32-S3 Companion BLE firmware
2026-11-10 09:06:07 -04:00
fdlamotte 4b71ed4498 Merge pull request #3613 from agessaman/feat/rak13302-auto-onboard-sleep
feat(rak3401): automatically sleep the RAK4631’s onboard SX1262 when paired with a RAK13302
2026-11-10 09:01:51 -04:00
fdlamotte 2367886a4c Merge pull request #3724 from akalinin-softvelum/feature/eink-busy-hook-v2
companion: keep mesh/BLE running during e-ink refresh
2026-11-10 08:40:43 -04:00
fdlamotte b7ab9fbc6f Merge pull request #3725 from Blake-Latchford/fix/espnow-no-lora-build
Fix Generic_ESPNOW_* builds on boards without a LoRa radio
2026-11-10 08:25:37 -04:00
fdlamotte 6f4cd39a6e Merge pull request #3648 from olimexsmart/feature/lilygo-t3-stm32
Add LilyGO T3 STM32 support
2026-11-10 08:23:03 -04:00
fdlamotte ad97616894 Merge branch 'dev' into feature/lilygo-t3-stm32 2026-11-10 08:22:52 -04:00
fdlamotte d6d51333c2 Merge pull request #3762 from wmacgreg/feature/nucleo-wl55jc
Add variant for ST Nucleo-WL55JC1 (STM32WL55JC) 🤖🤖
2026-11-10 08:14:51 -04:00
fdlamotte e6d141d6f7 Merge pull request #3785 from AlexandrTyshchenko/feature/companion-adc-multiplier
Companion: set/get adc.multiplier CLI command
2026-11-10 08:11:33 -04:00