Commit Graph
17 Commits
Author SHA1 Message Date
fdlamotte 4b71ed4498 Merge pull request #3613 from agessaman/feat/rak13302-auto-onboard-sleep
feat(rak3401): automatically sleep the RAK4631’s onboard SX1262 when paired with a RAK13302
2026-11-10 09:01:51 -04:00
Florent fa7ca3f418 rak_gps: simplify the rak driver, which now only handles i2c, for nmea use nmea driver directly 2026-11-08 08:47:34 -04:00
Florent df5a768c5d gps: add GpsDriver, handle the hardware and software switches in the drivers 2026-11-08 08:47:34 -04:00
agessaman d58042d8d2 fix(rak3401): sleep onboard SX1262 before boot voltage check
Move the onboard radio probe into RAK3401Board::begin() so a low-voltage
SYSTEMOFF at boot no longer leaves the RAK4631's onboard SX1262 in
standby. Add board startup tests and run them in CI.
2026-10-16 20:46:04 -07:00
agessaman de5d6697d1 feat(rak3401): auto-sleep optional onboard SX1262
Use the existing RAK3401 firmware roles for RAK4631 cores paired with a
RAK13302. Probe the optional onboard radio and put it into cold sleep
before handing SPI to the primary radio, removing seven duplicate build
environments.

Preserve BUSY startup readiness, release probe pulls before sleep, and
disconnect unused GPIO input buffers during cleanup. Add focused tests
for sequencing, missing signatures, timeouts, and failed sleep readback.

Validated with four native tests, seven firmware-role builds, and repeater
boot checks on RAK4631 + RAK13302. Supply current was not measured.
2026-10-16 19:02:23 -07:00
agessaman 51cbab5311 feat(rak3401): report onboard SX1262 sleep state via BUSY
BUSY is driven low in STDBY_RC and high while asleep, so reading it either
side of the sleep gives a non-invasive readback of the state the chip was
found in and the state it was left in. Confirmed on hardware.

This is what makes the sleep observable at all. The only other symptom of
a failed sleep is ~600 uA, which is below what an inline USB meter can
resolve, so without this a regression would be silent.

It immediately earned itself: busy_before reads 0 on every boot, showing
the cold sleep does not survive an MCU reset. GPIOs revert to input during
reset, NSS stops being driven high, and the falling edge wakes the chip.
The helper re-sleeps it, so this is self-healing, but it means the chip is
never found already asleep.
2026-08-17 22:19:49 -07:00
agessaman 61ae0920df feat(rak3401): cold-sleep RAK4631 onboard SX1262 on RAK13302 builds
A RAK4631 core paired with a RAK13302 leaves the core's own SX1262
powered but never initialized, idling in STDBY_RC for the life of the
board. Firmware cannot cut its supply -- P1.05 is the RF switch rail,
not the radio's -- so bring it up on its own pins just long enough to
issue a cold sleep, before std_init() repins SPI onto the RAK13302.

Gated behind RAK4631_ONBOARD_SX1262_SLEEP and exposed through seven
RAK_4631_13302_* envs, so RAK_3401_* artifacts are unchanged.

The sleep is issued regardless of what begin() returns: Module::init()
runs first, so SPI stays usable even if TCXO calibration fails. NSS is
then held high, since the SX1262 wakes on an NSS falling edge.

Verified on RAK19007 + RAK4631 + RAK13302: begin=0 sleep=0, RAK13302
init clean (device_errors=0x0000), TX and RX both confirmed. The
current saving itself is derived from the datasheet (600 uA STDBY_RC
-> 160 nA cold sleep) and is not measured.
2026-08-17 21:04:06 -07:00
Scott Powell 0a8a0a4904 * Refactor: removed duplicated radio_rng_seed(), radio_set_params(), radio_set_tx_power() 2026-05-01 14:47:07 +10:00
OverkillFPV 958204c7f1 Merge branch 'dev' into lora-longer-preamble 2026-04-16 20:43:46 +10:00
overkillfpv f0ec5d2ae7 changed to set the preamble on radio settings change 2026-03-29 21:45:16 +11:00
João Brázio 274e00df50 Merge remote-tracking branch 'upstream/dev' into 2026/remote-lna 2026-03-16 09:37:55 +00:00
João Brázio 9a95e25ef2 Remove unused RX boosted gain mode functions and related preprocessor directives across multiple variants 2026-03-05 18:38:57 +00:00
Wessel Nieboer 67d22401b1 Pass rtc_clock to all MicroNMEALocationProvider instances
Enable GPS time synchronization across all variants by passing
&rtc_clock to MicroNMEALocationProvider. When GPS gets a valid
fix, the RTC clock is now updated automatically every 30 minutes.

Updated 16 variants: rak4631, lilygo_tbeam_SX1262, rak_wismesh_tag,
lilygo_tbeam_supreme_SX1262, thinknode_m3, heltec_v4, thinknode_m1,
lilygo_tbeam_SX1276, meshadventurer, nano_g2_ultra, heltec_v3,
promicro, xiao_c3, heltec_tracker_v2, keepteen_lt1, heltec_mesh_solar.
2026-03-03 15:45:07 +01:00
João Brázio 71136671bd Implement remote lna toggle cli cmd 2026-02-10 15:02:23 +00:00
Wessel Nieboer d0720c63c2 Allow negative tx power
Like SX1262 allows -9 dBm lowest, some allow lower but that probably
isn't useful
2026-02-06 02:24:51 +01:00
chrisdavis2110 ed5d2909fc updated variant rak3401 2026-01-17 22:54:20 -08:00
chrisdavis2110 06c4ca19ab added variant rak3401 2026-01-13 10:06:50 -08:00