* WIP
* check using protocol version
* revert
* clean up
* sdp cid argument
* WIP
* WIP
* test
* clean up
* clean up
* fixes
* clean up
* clean up
* clean up
* conditional checks
* tests for both dual and single peer connection
* test
* test
* test
* type check
* test
* todo
* munges
* combined config
* populate mid
* limit to receive only
* clean up
* clean up
* clean up
* older test
* clean up
* alternative audio codec
* dtx
* don't need to copy
* Anunay feedback
* use the available peer connection
* publisher check
* WIP
* WIP
* WIP
* no mid
* media sections requirement
* mage generate
* WIP
* WIP
* set data channel receive size for test
* handle early media better
* WIP
* do not do ICERestart if no subscriber
* WIP
* WIP
* WIP
* WIP
* WIP
* WIP
* start up subscriber RTCP worker
* WIP
* WIP
* clean up
* clean up
* flag to indicate use of single peer connection
* remove unused interface method
* clean up
* clean up
* Jie feedback #1
* deps
* do not access subscriber in one shot mode
* more places for one shot mode
* more one shot fixes
* deps
* deps
* test
* Thottle the publisher data channel sending when subscriber is slow
Avoid the publisher overwhelm the sfu data channel buffer when
the subscriber has lower receive bitrates. It will drop message
if the subscriber is considered too slow to block the entire room.
* Enable nack in mediaengine and disable it in transceiver as need
pion doesn't support per transciver codec configuration, so the nack of this session will be disabled
forever once it is first disabled by a transceiver.
https://github.com/pion/webrtc/pull/2972
* file output
* wake under lock
* keep track of RTX bytes separately
* packet group
* Packet group of 50ms
* Minor refactoring
* rate calculator
* send bit rate
* WIP
* comment
* reduce packet infos size
* extended twcc seq num
* fix packet info
* WIP
* queuing delay
* refactor
* config
* callbacks
* fixes
* clean up
* remove debug file, fix rate calculation
* fmt
* fix probes
* format
* notes
* check loss
* tweak detection settings
* 24-bit wrap
* clean up a bit
* limit symbol list to number of packets
* fmt
* clean up
* lost
* fixes
* fmt
* rename
* fixes
* fmt
* use min/max
* hold on early warning of congestion
* make note about need for all optimal allocation on hold release
* estimate trend in congested state
* tweaks
* quantized
* fmt
* TrendDetector generics
* CTR trend
* tweaks
* config
* config
* comments
* clean up
* consistent naming
* pariticpant level setting
* log usage mode
* feedback
* Add support for "abs-capture-time" extension.
Currently, it is just passed through from publisher -> subscriber side.
TODO: Need to store in sequencer and restore for retransmission.
* abs-capture-time in retransmissions
* clean up
* fix test
* more test fixes
* more test fixes
* more test fixes
* log only when size is non-zero
* log on both sides for debugging
* add marshal/unmarshal
* normalize abs capture time to SFU clock
* comment out adding abs-capture-time from registered extensions
* Buffer size config for video and audio.
There was only one buffer size in config.
In upstream, config value was used for video.
Audio used a hard coded value of 200 packets.
But, in the down stream sequencer, the config value was used for both
video and audio. So, if video was set up for high bit rate (deep
buffers), audio sequencer ended up using a lot of memory too in
sequencer.
Split config to be able to control that and also not hard code audio.
Another optimisation here would be to not instantiate sequencer unkess
NACK is negotiated.
* deprecate packet_buffer_size
* Add control of playout delay
Add config to enable playout delay. The delay will be limited by
[min,max] in the config option and calculated by upstream & downstream
RTT.
* check protocol version to enable playout delay
* Move config to room, limit playout-delay update interval, solve comments
* Remove adaptive playout-delay
* Remove unused config
* Add interface and ipfilter to udpmux option
* validate external ip is accessable by client
* add context
* use external ip only for firefox
* fix mapping error
* Update pion/ice and use external ip only for firefox
* Use single external ip for NAT1To1Ips if validate failed
* update pion/ice
- ticker.Stop always
- clean up timer func (if they are added) on participant close
- sequencer test enhancement to add a real packet after a pdding packet
Now only set mapping when user_external_ip enabled or node_ip is
explicitly set. If multiple local address resolved to same external
ip, only the first one will be mapped to external, avoid candidate
conflict between different clients.
It's my understanding that the nodeIP config can be set to ensure that a
specific IP is provided for the host candidate. The code being changed
here was added as a convenience so that:
| By giving it STUN servers, it should be
| connectable even without passing in --node-ip explicitly
We'd prefer to be able to specify a nodeIP and then as a side effect
have a STUN server added.
When deployed via Docker and without using host networking, we'll be
assigned an IP behind NAT. By giving it STUN servers, it should be
connectable even without passing in `--node-ip` explicitly
Raja Subramanian